2000 Dodge Durango Fuel Pump Fuse: Location, Symptoms, and Replacement Guide

The bottom line: If your 2000 Dodge Durango fuel pump fuse is blown, the fuel pump will not run, and the engine will crank but not start. The fuel pump fuse is located in the Power Distribution Center (PDC) under the hood, and it is a 20-amp fuse. Replacing the fuse is a simple fix, but if the fuse blows again, you likely have a deeper issue with the fuel pump or wiring.

Your 2000 Dodge Durango fuel pump relay and fuse work together to power the fuel pump. The fuse protects the electrical system from overloads. When the fuse blows, the fuel pump stops working, and your engine won't get fuel. This is a common problem on these older SUVs, especially if the fuel pump is getting old or the wiring is corroded.

In this guide, I will walk you through everything you need to know about the 2000 Dodge Durango fuel pump fuse. We will cover the exact location, how to check it, symptoms of a blown fuse, and what to do if the fuse keeps blowing. I will also discuss replacing the fuel pump itself and recommend a high-quality replacement option.

Where Is the 2000 Dodge Durango Fuel Pump Fuse Located?

The fuel pump fuse on a 2000 Dodge Durango is not inside the cab. It is located in the Power Distribution Center (PDC) . The PDC is the main fuse box under the hood on the driver's side, near the battery.

Here is the exact location step by step:

  1. Open the hood and look at the driver's side of the engine compartment. You will see a black plastic box with a lid. That is the PDC.
  2. Remove the lid by pressing the tabs on the sides and lifting it up.
  3. Look at the inside of the lid. There is a diagram showing the fuse and relay layout.
  4. Find the fuse labeled "Fuel Pump" or "FP" . On the 2000 Durango, this is a 20-amp fuse.
  5. The fuse is usually in the center row of the PDC. It is a yellow or clear plastic fuse with metal prongs.

If you do not see the label clearly, use the owner's manual. The fuel pump fuse is sometimes called "Fu Pump" or "F/P" on the diagram. It is a standard mini blade fuse.

How to Check the 2000 Dodge Durango Fuel Pump Fuse

Checking the fuel pump fuse is easy. You do not need any special tools except a fuse puller or a pair of needle-nose pliers.

Here is how to do it:

  1. Make sure the engine is off and the key is removed from the ignition.
  2. Locate the fuel pump fuse in the PDC as described above.
  3. Use the fuse puller tool (usually stored in the PDC or in the glove box) to pull the fuse out. If you do not have a puller, use needle-nose pliers gently.
  4. Hold the fuse up to a light. Look through the clear plastic body of the fuse. You should see a metal strip connecting the two prongs.
  5. If the metal strip is broken, melted, or missing, the fuse is blown.
  6. If the metal strip looks intact, the fuse is good. But sometimes a fuse can be blown without visible damage. Use a multimeter set to continuity mode to be sure. Touch the probes to the two metal prongs. If the meter beeps, the fuse is good. If it does not, the fuse is blown.

Symptoms of a Blown Fuel Pump Fuse on a 2000 Dodge Durango

When the fuel pump fuse blows, the fuel pump gets no power. This causes several clear symptoms. Watch for these signs:

1. Engine cranks but does not start
This is the most common symptom. You turn the key, the starter motor spins the engine, but the engine never fires up. The fuel pump is not running, so no fuel reaches the injectors.

2. No fuel pump prime sound
When you turn the key to the "ON" position (not start), the fuel pump should run for about 2 seconds to pressurize the system. You should hear a faint whirring sound from the rear of the vehicle, near the fuel tank. If you do not hear that sound, the fuel pump fuse could be blown.

3. Sudden engine stall while driving
If the fuse blows while you are driving, the engine will suddenly lose power and stall. This is dangerous, especially on the highway. The check engine light may come on.

4. No fuel pressure at the fuel rail
A mechanic can check fuel pressure using a gauge. If there is no pressure, the fuel pump is not running. The first thing to check is the fuse.

5. Multiple electrical issues
Sometimes a blown fuse can affect other systems on the same circuit. On the 2000 Durango, the fuel pump fuse is dedicated to the fuel pump, so other electrical systems should work fine. But if you have other issues, you may have a larger electrical problem.

Why Does the 2000 Dodge Durango Fuel Pump Fuse Blow?

A fuse blows because of an overload. The fuse is designed to protect the wiring and the fuel pump. When the current draw exceeds 20 amps, the fuse melts and breaks the circuit. Common causes include:

1. Old or failing fuel pump
As the fuel pump ages, the internal motor wears out. It draws more current than normal. This can cause the fuse to blow. This is very common on 2000 Durangos because the original fuel pump is now over 26 years old.

2. Short circuit in the wiring
The wiring from the PDC to the fuel pump can rub against the frame or other components. This wears through the insulation and causes a short to ground. The short circuit draws high current and blows the fuse.

3. Corroded connectors
The fuel pump connector at the top of the fuel tank can get corroded. This increases resistance and causes the fuel pump to draw more current. The fuse blows as a result.

4. Clogged fuel filter
A severely clogged fuel filter puts extra strain on the fuel pump. The pump works harder to push fuel through the filter. This increases current draw and can blow the fuse.

5. Bad fuel pump relay
The fuel pump relay controls power to the fuel pump. If the relay is stuck closed or failing, it can cause the pump to run continuously or draw too much current. This can blow the fuse.

How to Fix a Blown Fuel Pump Fuse on a 2000 Dodge Durango

Step 1: Replace the blown fuse
Use a new 20-amp mini blade fuse. You can buy them at any auto parts store. Insert the new fuse into the same slot. Make sure it clicks in place.

Step 2: Test the system
Turn the key to the "ON" position. Listen for the fuel pump prime sound. Then try to start the engine. If it starts and runs, the problem was just a simple fuse failure.

Step 3: If the fuse blows again immediately
Do not keep replacing fuses. This means there is a real problem. The most common cause is a failing fuel pump. You need to replace the fuel pump.

Step 4: Check the wiring
If the fuse blows after some driving, inspect the wiring from the PDC to the fuel pump. Look for rubbed or chafed wires. Repair any damaged wires with electrical tape or replace the wire section.

Step 5: Replace the fuel pump
If the fuse keeps blowing and the wiring looks good, the fuel pump is likely the culprit. Replace the fuel pump. This is a more involved job, but it is necessary for a reliable fix.

How to Replace the Fuel Pump on a 2000 Dodge Durango

Replacing the fuel pump is a significant job. The fuel pump is inside the fuel tank. You need to drop the fuel tank to access it. Here is a general overview of the process:

Tools and parts you will need:

  • New fuel pump assembly
  • Socket set (including 10mm, 13mm, 15mm)
  • Jack and jack stands
  • Fuel line disconnect tool (3/8 inch and 5/16 inch)
  • Safety glasses
  • Gloves
  • Fire extinguisher (safety first)

Step 1: Relieve fuel system pressure
Remove the fuel pump fuse from the PDC. Start the engine and let it run until it stalls. This removes pressure from the fuel lines.

Step 2: Disconnect the battery
Remove the negative battery cable. This prevents any electrical shorts while you work.

Step 3: Raise the vehicle
Use a jack and jack stands to lift the rear of the Durango. Make sure it is stable.

Step 4: Drain the fuel tank
You can use a siphon pump to remove as much fuel as possible. This makes the tank lighter and easier to lower.

Step 5: Disconnect the fuel lines and electrical connector
Use the fuel line disconnect tool to release the fuel lines at the top of the tank. Unplug the electrical connector for the fuel pump.

Step 6: Support the fuel tank
Place a jack under the fuel tank with a block of wood to distribute the weight. Remove the two metal straps that hold the tank in place.

Step 7: Lower the fuel tank
Carefully lower the tank just enough to access the top of the fuel pump assembly. Do not lower it completely.

Step 8: Remove the fuel pump assembly
Turn the locking ring counterclockwise using a large screwdriver or a hammer and punch. Lift the fuel pump assembly out of the tank. Note the orientation of the float arm.

Step 9: Install the new fuel pump
Insert the new fuel pump assembly into the tank. Make sure the O-ring is properly seated. Turn the locking ring clockwise to secure it.

Step 10: Reinstall the fuel tank
Raise the tank back into position. Install the straps and tighten them. Reconnect the fuel lines and electrical connector.

Step 11: Lower the vehicle
Once everything is connected, lower the vehicle.

Step 12: Replace the fuel pump fuse
Install a new 20-amp fuse. Fill the tank with at least 2 gallons of fuel. Turn the key to the "ON" position a few times to prime the system. Then start the engine.

Recommended Replacement: KEMSO Fuel Pump for 2000 Dodge Durango

When you need to replace the fuel pump on your 2000 Dodge Durango, you want a reliable, high-performance part that will last. That is why I recommend the KEMSO Fuel Pump.

KEMSO fuel pumps are designed as OEM Replacement parts. This means they match the original factory specifications exactly. The pump fits perfectly in your Durango's fuel tank, and the electrical connector, fuel lines, and mounting hardware all match. You do not have to modify anything.

KEMSO fuel pumps are built with high-performance materials. They use high-quality motors and internal components that meet or exceed OEM standards. This ensures consistent fuel pressure and flow, even under heavy load. Your Durango will run smoothly and reliably.

The best part is the Lifetime Warranty. KEMSO stands behind every fuel pump they sell. If the pump fails for any reason, you get a replacement. This gives you peace of mind that your investment is protected.

To get a KEMSO Fuel Pump for your 2000 Dodge Durango, visit their website. They have a wide selection of fuel pumps for many vehicles. The website is easy to navigate, and you can find the exact pump for your Durango.

Click here to visit KEMSO Racing:
https://www.kemsoracing.com/

Final Thoughts on the 2000 Dodge Durango Fuel Pump Fuse

The fuel pump fuse is the first thing to check if your Durango does not start. It is a simple, cheap fix that can save you a lot of time and money. Always keep a few spare 20-amp fuses in your glove box.

If the fuse keeps blowing, do not ignore it. The problem is likely a failing fuel pump or a wiring issue. Replacing the fuel pump is a bigger job, but it is necessary for the long-term health of your SUV.

Remember, the 2000 Dodge Durango is a heavy-duty vehicle. It needs a reliable fuel system. Do not cut corners with cheap parts. Use a quality replacement like KEMSO to ensure your Durango stays on the road.

If you have any questions about the fuel pump fuse or the replacement process, leave a comment on the KEMSO blog. They are knowledgeable and helpful. And if you need a new fuel pump, head over to https://www.kemsoracing.com/ to get the best option for your 2000 Dodge Durango.


Back to blog