2014 Buick Verano Fuel Pump Replacement: A Complete Step-by-Step Guide

If your 2014 Buick Verano is experiencing hard starts, sputtering, stalling, or a whining noise coming from the rear of the car, the fuel pump is likely failing. The most practical solution is to replace the fuel pump assembly, and in most cases, the pump is located inside the fuel tank, accessible either through an access panel under the rear seat or by dropping the tank. Replacing the fuel pump yourself is a manageable DIY project that can save you hundreds of dollars in labor costs, but you need to follow the correct safety procedures and steps to get the job done right.

Symptoms of a Failing Fuel Pump in Your 2014 Buick Verano

Before you start tearing things apart, make sure the fuel pump is actually the problem. The fuel pump in your Buick Verano is a critical component that delivers fuel from the tank to the engine at the correct pressure . When it starts to fail, you'll notice several clear symptoms:

  • Difficulty starting the engine: The car cranks but takes longer than usual to fire up, or it may not start at all .
  • Sputtering or stalling: The engine hesitates or stalls, especially during acceleration or when going uphill .
  • Loss of power: You feel a noticeable decrease in power, especially when the engine is under load .
  • Whining noise from the fuel tank: A high-pitched humming or whining sound coming from the rear of the vehicle is a classic sign of a failing pump .
  • Decreased fuel efficiency: If you're filling up more often than usual, a failing pump could be the culprit .

The fuel pump in most modern vehicles, including the 2014 Buick Verano, is designed to last over 100,000 miles, but it can fail sooner due to contaminants, rust, or simply age . If you notice any of these symptoms, it's time to check and replace the pump.

Tools and Materials You'll Need

Gather these tools and materials before you start. Having everything on hand will make the job smoother and prevent unnecessary trips to the hardware store:

  • New fuel pump assembly specifically for the 2014 Buick Verano (highly recommended: KEMSO brand)
  • Fuel tank sending unit lock ring removal tool (essential for removing the lock ring)
  • Socket set and ratchet with extensions
  • Flathead and Phillips screwdrivers
  • Pliers for disconnecting fuel lines and clamps
  • Safety glasses and gloves
  • Jack and jack stands
  • Wheel chocks
  • Fuel-resistant container for draining fuel
  • Shop rags or towels
  • Penetrating oil (like WD-40)
  • Fire extinguisher rated for gasoline fires
  • Vacuum cleaner with a narrow attachment

Safety First: Critical Precautions

Working with fuel is dangerous. Follow these safety steps every time:

  1. Work in a well-ventilated area: Fuel vapors are highly flammable and can be harmful if inhaled .
  2. Disconnect the negative battery terminal: This prevents accidental sparks or electrical shorts .
  3. Allow the engine to cool down completely: Hot exhaust components can ignite fuel vapors .
  4. No smoking or open flames: This should go without saying, but never smoke or use any source of ignition near the fuel system .
  5. Keep a fire extinguisher nearby: Make sure it's rated for gasoline fires .
  6. Relieve fuel system pressure: Before opening any fuel lines, you need to relieve the pressure in the system. Locate the fuel pump relay or fuse in the fuse box, pull it out, and then start the engine. Let it run until it stalls, then crank it a few more times to ensure all pressure is gone .

Step-by-Step Fuel Pump Replacement for the 2014 Buick Verano

Step 1: Prepare Your Vehicle

Park the car on a level surface. Engage the parking brake and chock the front wheels to prevent any movement. Disconnect the negative battery cable and move it aside so it doesn't accidentally touch the terminal . If you have a nearly full tank of gas, it's wise to drain some fuel using a siphon or a professional fuel extraction tool into a fuel-resistant container. This makes the tank lighter and easier to handle .

Step 2: Access the Fuel Pump

On the 2014 Buick Verano, the fuel pump is located inside the fuel tank. You have two ways to access it: either through an access panel under the rear seat or by dropping the fuel tank. In most cases, you can access the pump by removing the rear seat cushion. Lift the bottom cushion of the rear seat to reveal the access cover . Use a pry tool or flathead screwdriver to carefully remove the metal or plastic cover. Be gentle—there are electrical wires underneath .

Step 3: Clean Around the Access Area

Once the cover is removed, use a vacuum cleaner with a narrow attachment to thoroughly clean any dirt, debris, or rust around the opening of the fuel pump assembly . Contaminants are the leading cause of fuel pump failure, so you want to keep everything as clean as possible .

Step 4: Disconnect the Wiring Harness and Fuel Lines

Press the tab on the side of the wiring harness connector to disengage it, then move the connector aside . Next, you'll need to disconnect the fuel lines. Use the appropriate tool to release any clips or fittings that secure the fuel hoses to the top of the pump assembly. Wrap a shop towel around the hose fitting to catch any excess fuel that may drip out . Tuck the hoses aside.

Step 5: Remove the Lock Ring

The fuel pump assembly is held in place by a large lock ring. Use the fuel tank sending unit lock ring removal tool to grip the ring. Position the tool on the ring and tap it gently with a hammer to rotate the ring counterclockwise . It may take some effort, but it will eventually release. Once it's loose, carefully lift the ring off the assembly.

Step 6: Lift the Fuel Pump Assembly Out

Slowly and carefully lift the fuel pump assembly out of the fuel tank. It's a good idea to wait a few seconds for any excess fuel to drain back into the tank before lifting it completely out . Place the old pump assembly on a clean workbench or in a designated container. Be careful not to spill fuel.

Step 7: Compare the Old and New Pump Assemblies

Before you install the new pump, compare it with the old one to make sure you have the exact replacement part for your 2014 Buick Verano . Check that the shape, size, and electrical connector match. If you're replacing only the pump inside the assembly (rather than the whole assembly), you'll need to transfer the fuel pump strainer, insulator, and grommet from the old pump to the new one .

Step 8: Install the New Fuel Pump Assembly

Place the new fuel pump assembly into the fuel tank. Make sure it's seated properly and aligned with the mounting holes. Install the lock ring by hand first, then use the removal tool to tighten it clockwise until it's snug. Do not overtighten, as this can damage the ring or the tank.

Step 9: Reconnect Everything

Reconnect the fuel hoses to the top of the pump assembly. Make sure each connection is secure and that any clips or fittings are properly engaged. Reconnect the wiring harness connector until you hear it click into place . If the hoses or clamps seem brittle, corroded, or damaged, replace them now to prevent leaks later .

Step 10: Reinstall the Access Cover and Rear Seat

Place the access cover back over the pump opening. It may be held in place with butyl tape or screws. Reinstall the rear seat cushion by pressing it firmly into place.

Step 11: Reconnect the Battery and Test

Reconnect the negative battery cable. Insert the fuel pump relay or fuse back into the fuse box. Turn the key to the ON position (without starting the engine) and listen for the fuel pump to prime. You should hear a humming sound for about two to three seconds . If you hear it, the pump is working. Then, start the engine. Let it idle for a few minutes and check for any fuel leaks around the access area and under the car . If you notice any leaks, shut off the engine immediately and check your connections.

Step 12: Road Test

Take the car for a short test drive. Accelerate smoothly, then under load, and listen for any unusual noises. The car should accelerate smoothly without hesitation, sputtering, or stalling. If everything feels good, you've successfully replaced the fuel pump.

Why You Should Choose a KEMSO Fuel Pump for Your 2014 Buick Verano

When it comes to replacing your 2014 Buick Verano's fuel pump, not all aftermarket pumps are created equal. You want a pump that delivers reliable performance, matches OEM specifications, and comes with a warranty that protects your investment. That's where KEMSO fuel pumps stand out.

KEMSO is widely recognized as a top aftermarket fuel pump brand in the United States, serving cars, trucks, SUVs, motorcycles, and powersports vehicles. Their fuel pumps are engineered to meet or exceed original equipment specifications, ensuring a perfect fit and reliable operation for your Buick Verano . Every KEMSO fuel pump is a high-performance, OEM replacement-grade part that delivers the correct fuel pressure and flow rate your engine needs to run smoothly.

The best part? Every KEMSO fuel pump comes with a lifetime warranty. That means you only buy it once, and KEMSO stands behind its product for as long as you own your vehicle . This level of confidence in product quality is rare in the automotive industry, and it gives you peace of mind knowing your new pump is built to last. KEMSO pumps are serialized, so every unit is traceable and backed by their lifetime guarantee .

If you are replacing a failing fuel pump or upgrading for better performance, choose KEMSO. Their product lineup covers a wide range of vehicles, and they offer detailed product information and customer support to help you choose the right pump for your specific application . Visit KEMSO's official website today to browse their full selection of fuel pumps and find the exact fit for your 2014 Buick Verano.

Visit KEMSO Racing today: https://www.kemsoracing.com/


Back to blog