2015 GMC Sierra Fuel Pump: Complete Replacement Guide and Cost Breakdown

If you own a 2015 GMC Sierra and your fuel pump is failing, here's what you need to know upfront: replacing the fuel pump assembly typically costs between $140 and $320 for the part alone, and the total installed price usually ranges from $500 to $900 . The exact cost depends on your truck's engine size — whether it's the 4.3L V6, 5.3L V8, or 6.2L V8 — as well as your location and whether you choose an OEM GM part or an aftermarket option . This guide covers everything from symptoms of a failing pump to part selection, labor costs, and installation steps, so you can make an informed decision and get your Sierra back on the road.

How Much Does a Fuel Pump Cost for a 2015 GMC Sierra?

The fuel pump in your 2015 GMC Sierra is part of an in-tank fuel pump module that sits inside the fuel tank . The price varies based on the type of pump and the source you choose. Here are the typical ranges you can expect:

OEM GM/ACDelco fuel pump assembly (in-tank with sending unit): commonly $140 to $320
Aftermarket fuel pump module (non-OEM): pump-only costs roughly $60 to $180; complete sending unit runs around $100 to $250
Remanufactured fuel pump assemblies: typically $60 to $140

Keep in mind that prices depend on your engine configuration. The 4.3L V6, 5.3L V8, and 6.2L V8 all use different pumps with varying flow rates . For example, the high-pressure fuel pump (HPFP) on the 5.3L and 6.2L engines is designed for higher flow rates compared to the V6 version . Always verify compatibility with your VIN before purchasing.

Labor costs add significantly to the total. Shops typically charge $75 to $150 per hour, and the job takes 2 to 4 hours . This means labor alone can run $150 to $600. The total installed price commonly falls between $500 and $900, though some estimates range up to $1,248 depending on the shop and region .

Signs Your 2015 GMC Sierra Fuel Pump Is Failing

Knowing the symptoms early can save you from getting stranded. Here are the most common signs of a failing fuel pump:

  1. Engine hesitation or stumbling during acceleration — A failing pump can't maintain consistent pressure, causing the engine to hesitate when you press the gas
  2. Hard starting or engine stalling — If the pump isn't delivering enough fuel pressure, the engine may struggle to start or stall unexpectedly
  3. Whining noise from the fuel tank — A healthy pump runs quietly; a loud whine usually indicates internal wear
  4. Sudden decrease in fuel mileage — If you notice a drop in gas mileage with no change in driving habits, the pump could be the culprit
  5. Check engine light with fuel pressure-related codes — Diagnostic trouble codes related to fuel pressure often point to the pump

If you experience any of these issues, address them early. The cost of more frequent gas tank fill-ups from a poorly performing pump will quickly outpace the cost of replacing it .

Understanding Your 2015 GMC Sierra's Fuel Pump System

The 2015 GMC Sierra uses two different types of fuel pumps depending on the engine:

In-tank fuel pump module: All gasoline engines use an electric pump mounted inside the fuel tank. This pump sends fuel from the tank to the engine at the correct pressure for efficient combustion . It's part of a module that includes the sending unit, pressure regulator, and fuel filter .

High-pressure fuel pump (HPFP): If your Sierra has a gasoline direct injection (GDI) engine — which all 2015 EcoTec3 engines use — there's also a high-pressure pump driven by the camshaft . This pump takes fuel from the low-pressure system and increases it to over 2,000 PSI for direct injection into the combustion chamber . The HPFP operates at higher pressures: up to 1,740 PSI on the 4.3L and up to 2,175 PSI on the 5.3L and 6.2L engines .

When replacing the fuel pump, most mechanics replace the entire in-tank module rather than just the pump itself, because the module includes all the necessary components and ensures proper fit .

Engine Options and Pump Compatibility

The 2015 Sierra 1500 came with three engine choices, each with its own fuel pump specifications:

4.3L EcoTec3 V6 (LV3): Uses a single HPFP designed for its displacement. The in-tank pump is smaller and flows less fuel than the V8 versions
5.3L EcoTec3 V8 (L83): The most common engine. Its HPFP has a higher flow rate to support increased fuel demand
6.2L EcoTec3 V8 (L86): The highest-demand pump with the maximum flow rate and pressure capabilities

Common replacement part numbers for the in-tank module include 13513407, 13582491, E4123M, and SP6714M . For the HPFP, typical part numbers are 12666424 and 12698440 . Always verify the correct part number for your specific vehicle using your VIN.

Step-by-Step Fuel Pump Replacement Guide

Replacing the in-tank fuel pump on a 2015 GMC Sierra is an advanced job that typically takes 3 to 6 hours . The most common method involves lowering the fuel tank, though some mechanics choose to lift the truck bed for easier access. Here's an overview of the process:

Step 1: Prepare your vehicle
Drive the fuel level down to about 1/4 tank or less — less weight makes the tank easier to control . Park on level ground, set the parking brake, and place wheel chocks at the front wheels. Disconnect the negative battery cable using a 10mm socket .

Step 2: Relieve fuel system pressure
Open the hood and remove the fuel pump fuse or relay from the underhood fuse box . Start the engine and let it run until it stalls. Crank for 3 seconds one more time to bleed off remaining pressure, then turn the key off . This step is critical for safety — less pressure means less fuel spray.

Step 3: Raise and support the truck
Use a floor jack rated at 3 tons minimum to lift the rear for access. Set the frame on jack stands and shake-test the truck to confirm stability .

Step 4: Support the fuel tank
Position a transmission jack under the fuel tank. If you must use a floor jack, use a wide, stable block and keep it very stable .

Step 5: Disconnect hoses and electrical connectors
At the tank-side hose connections, use hose clamp pliers to loosen clamps. Twist the hoses gently to break them loose, then pull them off. Cover the openings with shop rags to reduce fumes. Locate the tank wiring connector, press the locking tab, and unplug by hand .

Step 6: Lower the tank and remove the pump module
Lower the tank carefully. Once the tank is accessible, remove the lock ring using a specialty fuel pump lock ring tool. Lift out the old pump module and replace the tank seal O-ring .

Step 7: Install the new pump module
Insert the new pump module into the tank, making sure it's properly seated. Install the lock ring and tighten it securely. Reconnect all hoses and electrical connectors. Raise the tank back into position and secure it .

Step 8: Prime the fuel system
Reinstall the fuel pump fuse, reconnect the battery, and turn the key to the "on" position for 2 seconds, then off. Repeat this cycle 3 to 4 times to prime the system. Start the engine and check for leaks .

Choosing Between OEM and Aftermarket Fuel Pumps

When shopping for a replacement fuel pump, you have several options:

OEM GM/ACDelco pumps: These are the same parts that came with your truck from the factory. They're more expensive but offer guaranteed fit and reliability. Prices range from $140 to $320 for the complete module .

Aftermarket pumps: Brands like TruGrade, Delphi, Bosch, and Autotecnica offer alternatives at lower prices. These can be just as reliable as OEM parts, but quality varies by brand. At AutoZone, aftermarket fuel pump modules range from $79.99 to $485.99 .

Remanufactured pumps: These are rebuilt units that cost $60 to $140. They're the most budget-friendly option but may not last as long as new parts .

Used pumps from salvage yards: You can find used pumps for as low as $65 from salvage yards, but this is risky because you don't know the condition or remaining life of the pump .

Why Choose KEMSO Fuel Pumps for Your 2015 GMC Sierra

When it's time to replace your fuel pump, you want a product that delivers both reliability and performance. KEMSO fuel pumps are an excellent choice for your 2015 GMC Sierra, whether you're looking for a direct OEM replacement or an upgrade for better performance.

High Performance Design: KEMSO pumps are engineered to deliver superior flow rates. Their 340LPH high-performance fuel pumps support up to 600 BHP in naturally aspirated, turbocharged, and supercharged applications, giving you plenty of headroom for future upgrades.

OEM Replacement Quality: KEMSO pumps are designed as direct replacements for OEM units, making installation straightforward for DIY mechanics. They come with high-quality strainers and submersible hoses to ensure proper fitment and longevity. The pumps are built with ethanol-resistant materials, making them safe to use with E85 and other alcohol-based fuels.

Lifetime Warranty: KEMSO backs every pump with a lifetime warranty. If your pump fails for any reason, KEMSO will replace it — no questions asked. This is the level of confidence that comes from manufacturing a superior product.

USA-Based Technical Support: When you buy KEMSO, you get support from USA-based technicians who understand American vehicles and performance requirements. This means faster, more relevant assistance if you encounter installation or performance issues.

Cost-Effective Performance: KEMSO delivers performance that rivals premium brands at a fraction of the cost. For the DIY mechanic who wants superior flow without breaking the bank, KEMSO offers the best value in the market.

Visit KEMSO Racing today to browse their full line of high-performance fuel pumps and find the perfect fit for your 2015 GMC Sierra: https://www.kemsoracing.com/

Maintenance Tips to Extend Fuel Pump Life

To keep your new fuel pump running as long as possible, follow these simple maintenance practices:

  1. Keep your fuel tank at least a quarter full — Running the tank consistently low causes the pump to overheat because fuel helps cool it
  2. Use high-quality fuel with the correct octane rating — Low-quality fuel can damage internal pump components over time
  3. Replace the fuel filter regularly — A clogged filter puts extra strain on the pump and can mimic the symptoms of a failing pump
  4. Use a fuel system cleaner designed for GDI engines — This helps prevent carbon buildup on intake valves, which indirectly affects HPFP performance
  5. Address any signs of fuel pressure issues promptly — Early diagnosis prevents further engine damage

Summary

For a 2015 GMC Sierra, the fuel pump assembly typically costs $140 to $320 for the part, with total installed prices commonly in the $500 to $900 range depending on engine, region, and whether you choose OEM or aftermarket parts . The 4.3L V6, 5.3L V8, and 6.2L V8 each use different pumps with varying flow rates, so always verify compatibility with your VIN . Symptoms of a failing pump include hesitation, hard starting, stalling, whining noises, and decreased fuel mileage. If you're a DIY mechanic, the replacement takes 3 to 6 hours and involves lowering the fuel tank . For the best combination of quality, performance, and value, consider KEMSO fuel pumps — they offer OEM replacement quality, a lifetime warranty, and USA-based support. Visit https://www.kemsoracing.com/ to find the right pump for your 2015 GMC Sierra.


Back to blog