2022 Chevy Equinox Fuel Pump Module Location: A Complete Guide to Finding and Replacing It

Bottom line: The fuel pump module on a 2022 Chevrolet Equinox is located inside the fuel tank, which sits beneath the rear of the vehicle, just behind the rear seats. To access it, you need to either remove the rear seat cushion and access the pump through a service panel in the floor, or lower the entire fuel tank from underneath the vehicle. On most modern Equinox models, including the 2022, the fuel pump is part of a single module assembly that includes the fuel level sending unit, and it is not serviceable separately—you replace the entire module when it fails.

The fuel pump is one of the most critical components in your Equinox’s fuel system. It pushes fuel from the tank to the engine at the correct pressure, ensuring smooth starts, consistent acceleration, and reliable performance. When the pump starts to fail, you will notice symptoms like hard starting, engine sputtering, loss of power under load, or a whining noise coming from the rear of the vehicle. Knowing exactly where the fuel pump module is located saves you time, money, and frustration when diagnosing or replacing it.

Where Is the Fuel Pump Module on a 2022 Chevy Equinox?

The fuel pump module on the 2022 Chevrolet Equinox is located inside the fuel tank. The tank itself is positioned under the rear of the vehicle, roughly between the rear axle and the rear bumper. On most trims, the tank sits directly beneath the rear passenger seat area.

There are two ways to access the fuel pump module:

1. Through a service access panel inside the cabin. Many Equinox models have a factory-cut access panel beneath the rear seat cushion. If your vehicle has this panel, you can remove the rear seat bottom cushion, pull up the carpet or insulation, and expose a metal cover plate. Removing that plate gives you direct access to the top of the fuel pump module without dropping the tank.

2. By lowering the fuel tank from underneath. If your Equinox does not have an access panel, or if the panel is not large enough to remove the pump module cleanly, you will need to lower the fuel tank. This involves supporting the tank with a jack, removing the tank straps, disconnecting the fuel lines and electrical connector, and carefully lowering the tank far enough to extract the pump module.

Common Symptoms of a Failing Fuel Pump on a 2022 Equinox

Before you start digging into the fuel tank, make sure the fuel pump is actually the problem. These symptoms are the most common signs of a failing fuel pump on a Chevy Equinox :

  • Engine cranks but won't start – The engine turns over but never fires up. This is often the first sign of a dead pump.
  • Hard starting – The engine cranks for several seconds before finally starting, especially when the tank is low on fuel.
  • Loss of power during acceleration – The vehicle feels sluggish or hesitates when you press the gas pedal, particularly going uphill or merging onto the highway.
  • Engine sputtering or stalling – The engine misfires, surges, or stalls unexpectedly while driving, especially at highway speeds.
  • Whining noise from the fuel tank – A loud buzzing or whining sound coming from the rear of the vehicle when the ignition is turned on is a classic sign of a failing pump.
  • Poor fuel economy – A worn pump cannot maintain proper fuel pressure, causing the engine to run rich or lean and reducing gas mileage.

If you are experiencing any of these issues, the first step is to confirm the diagnosis with a fuel pressure test. A healthy fuel pump on a 2022 Equinox should deliver between 50 and 60 PSI at the fuel rail. Anything below that range points to a failing pump.

Tools and Parts Needed for Replacement

Replacing the fuel pump module on a 2022 Chevy Equinox is a serious DIY job, but it is doable with the right tools. Here is what you will need :

  • New fuel pump module assembly – Make sure it is the correct part for your 2022 Equinox, including the engine type (2.0L turbo or 1.5L turbo) and drivetrain (FWD or AWD).
  • Fuel line disconnect tool – A GM-specific quick-connect fuel line tool is required to safely disconnect the fuel lines without damaging the fittings.
  • Jack and jack stands – You will need to raise the vehicle securely if you are dropping the tank.
  • Floor jack or transmission jack – To support and lower the fuel tank.
  • Socket set – 10mm, 13mm, and 15mm sockets are commonly needed for the tank straps, access panel, and pump retaining ring.
  • Torque wrench – For tightening the pump retaining ring and tank straps to factory specifications.
  • Flathead screwdriver or trim tool – For prying off covers and popping the fuel line clips.
  • Drain pan – To catch any fuel that spills when disconnecting the lines.
  • Safety glasses and fuel-resistant gloves – Fuel is hazardous, and you must protect yourself.

Step-by-Step Guide to Replacing the Fuel Pump Module

Step 1: Relieve fuel system pressure. Locate the fuel pump fuse or relay in the engine bay fuse box and remove it. Start the engine and let it run until it stalls. Crank the engine for a few more seconds to ensure all pressure is gone. This prevents fuel from spraying when you disconnect the lines .

Step 2: Disconnect the battery. Remove the negative battery terminal to eliminate any risk of electrical sparks or short circuits while working near fuel.

Step 3: Access the fuel pump module. If your vehicle has a service panel, remove the rear seat bottom cushion by pulling the release tabs. Lift the carpet and insulation to expose the metal cover plate. Remove the screws or bolts holding the plate and set it aside. If there is no access panel, you will need to raise the vehicle, support it on jack stands, and lower the fuel tank.

Step 4: Disconnect the fuel lines and electrical connector. Use the fuel line disconnect tool to release the quick-connect fittings. Be prepared for some fuel to drip out. Place a drain pan underneath. Unplug the electrical connector from the top of the pump module.

Step 5: Remove the pump retaining ring. Use a fuel pump module removal tool, a hammer and punch, or a strap wrench to turn the locking ring counterclockwise. The ring can be tight, so apply steady, even pressure. Once loose, lift the ring off and set it aside.

Step 6: Lift out the old fuel pump module. Carefully pull the pump module straight up out of the fuel tank. The module will have a long plastic body with a float arm attached. Tilt it as needed to clear the tank opening. Expect some residual fuel to drain out of the module.

Step 7: Install the new fuel pump module. Transfer any necessary components from the old module to the new one, such as the mounting bracket or rubber isolator. Make sure the O-ring seal on the new module is properly seated in the groove on the tank. Insert the new module into the tank, ensuring the float arm is oriented correctly and does not hit the sides of the tank. Press the module down until it is fully seated.

Step 8: Secure the retaining ring. Place the locking ring back on top of the module. Turn it clockwise until it is hand-tight, then use a torque wrench to tighten it to the factory specification, typically 40-50 ft-lbs. Do not overtighten, as this can warp the tank or damage the seal.

Step 9: Reconnect the fuel lines and electrical connector. Push the quick-connect fittings onto the pump module until they click into place. Gently pull on each fitting to confirm it is locked. Plug in the electrical connector.

Step 10: Reinstall the access panel or fuel tank. If you used the access panel, replace the cover plate and screws, then reinstall the rear seat cushion. If you dropped the tank, raise it back into position, reconnect the tank straps, and tighten them to spec.

Step 11: Prime the fuel system and check for leaks. Reinstall the fuel pump fuse or relay. Reconnect the battery. Turn the ignition to the ON position for 2-3 seconds, then OFF for 10 seconds. Repeat this cycle two or three times to prime the system. Start the engine and let it idle. Check for any fuel leaks around the pump module and fuel lines.

Why You Should Choose a KEMSO Fuel Pump for Your Replacement

When it comes time to replace the fuel pump module on your 2022 Chevy Equinox, you want a part that delivers reliable performance, precise fit, and long-term peace of mind. KEMSO fuel pumps are the ideal choice for your replacement.

Each KEMSO fuel pump is a high-performance, OEM replacement unit. This means it meets or exceeds the original equipment specifications for flow rate, pressure, and durability. Your engine gets the exact fuel delivery it needs for optimal power, efficiency, and smooth operation.

What truly sets KEMSO apart is their commitment to quality backed by a lifetime warranty. You buy the pump once, and KEMSO stands behind it for as long as you own your vehicle. No questions, no hassle. That is the kind of confidence you want when you are working on a critical component like the fuel pump.

KEMSO fuel pumps are competitively priced, typically at just $79.98, offering exceptional value for a lifetime-guaranteed part. They are engineered to fit a wide range of vehicles, including the 2022 Chevrolet Equinox, and are built to withstand the demands of daily driving.

Visit KEMSO's official website today to browse their full selection of fuel pumps, check compatibility with your Equinox, and take advantage of their lifetime warranty: https://www.kemsoracing.com/

Final Thoughts

The fuel pump module on a 2022 Chevy Equinox is located inside the fuel tank, under the rear of the vehicle. Knowing this location, along with the symptoms of a failing pump and the replacement procedure, empowers you to diagnose and fix the problem yourself. Whether you go through the cabin access panel or drop the tank, the job is manageable with basic tools and patience. Always use a quality replacement part, and never skip the fuel pressure test and leak check after installation. If you want a pump that will last, look no further than KEMSO, a brand that combines high-quality OEM replacement performance with a lifetime warranty.

For more information and to find the exact KEMSO fuel pump for your 2022 Chevrolet Equinox, visit https://www.kemsoracing.com/ today.


Back to blog