99 Chrysler 300M Fuel Pump: Replacement Guide

For a 1999 Chrysler 300M, the fuel pump is an electric, in-tank module assembly that includes the pump, sending unit, strainer, regulator, seal, and float. The engine is a 3.5L V6, and the correct replacement is a complete module matched to that engine and model year, not a universal pump alone. A failing pump usually causes hard starting, loss of power under load, stalling, whining from the tank, or a no-start condition. Before buying a 99 Chrysler 300M fuel pump, check fuel pressure, power and ground at the connector, the fuel pump relay, fuses, and the condition of the wiring. If those check out and pressure is low, replacing the complete module is the practical repair. On this car, the fuel filter and pressure regulator are integrated into the module inside the tank, so there is no separate serviceable inline filter to replace as a quick fix . The job usually requires lowering the fuel tank, which is why many owners choose a quality complete assembly rather than a cheap pump insert .

This guide is written for U.S. owners who want to diagnose the problem correctly, order the right part, understand the labor, and avoid replacing parts that are not bad. It also covers what to expect from the fuel gauge, how to confirm fitment, what a shop may charge, and how to protect the new pump after installation .

1. What the Fuel Pump Does on a 1999 Chrysler 300M

The 1999 Chrysler 300M uses a returnless-style fuel system with the pump mounted inside the fuel tank. The module pushes gasoline from the tank to the fuel rail at controlled pressure so the injectors can supply the 3.5L V6. Replacement modules for this application are commonly listed as 12V electric turbine-style in-tank assemblies with a quick-connect outlet, internal strainer, regulator, and fuel level sending unit .

Common fitment listings for the 1999 300M include part numbers such as E7137M, SP7137M, P74819M, FG0232, 67663, and F3148A, along with Mopar references including 5003958AA through 5003958AE and 4581046AB . These numbers matter because the same LH-platform cars were sold with different engines, and a listing for a 2.7L Concorde or Intrepid is not automatically the right match for a 3.5L 300M.

Key parts included in most complete module assemblies:

  1. Fuel pump motor that supplies flow and pressure.
  2. Fuel level sending unit and float that control the dash gauge.
  3. Strainer or pre-filter that screens fuel before it enters the pump.
  4. Fuel pressure regulator built into the module on these applications.
  5. Tank seal, gasket, or O-ring needed to prevent fuel vapor leaks.
  6. Electrical connector and outlet matched to the factory harness and fuel line .

A complete module is the safer choice for most DIY repairs. The pump, reservoir, regulator, sender, and strainer live together inside the tank. Reusing old brittle plastic, a worn float, or a tired sending unit can send you back under the car later.

2. Symptoms of a Bad 99 Chrysler 300M Fuel Pump

A weak pump does not always fail all at once. Many owners notice driveability problems for weeks before the car finally refuses to start. Low fuel pressure can feel like a ignition problem, a clogged injector, or a transmission issue, so testing matters.

The most common warning signs are:

  1. Long cranking before start. The engine turns over normally but needs extra time because pressure has bled down or the pump is slow to build pressure.
  2. No start with a healthy battery and starter. If the pump does not run at key-on, the engine may crank but never fire.
  3. Loss of power at highway speed or uphill. The engine may stumble, surge, or fall flat when fuel demand is highest.
  4. Stalling when hot, then restarting after cooldown. A worn pump motor can draw more current as it heats up and temporarily stop working.
  5. Whining or buzzing from the rear seat or fuel tank area. A louder-than-normal pump noise often points to a worn pump or restricted strainer.
  6. Fuel gauge that reads wrong or drops suddenly. The sending unit is part of the module, so gauge faults can occur with the same assembly .
  7. Check engine light with lean or misfire codes. Low pressure can cause lean operation and misfires, but codes alone do not prove the pump is bad.

Do not skip simple checks. A blown fuse, weak relay, corroded connector, damaged ground, or low battery voltage can look like a dead pump. A professional diagnosis normally includes a scan for codes, fuel pressure reading, and a check for voltage at the pump circuit. If the pump has power and ground but cannot make specified pressure, the module is the likely failure.

3. Confirm the Correct Part Before Ordering

The phrase “99 Chrysler 300M fuel pump” should always be matched with the exact vehicle details. The 300M was part of the Chrysler LH family, and parts catalogs often group it with the Concorde, LHS, Dodge Intrepid, and several V6 engines from 1998–1999 . That wide coverage is useful, but it also creates confusion.

Use this 5-step fitment check:

  1. Confirm the year: 1999.
  2. Confirm the model: Chrysler 300M, not the later 300, 300C, or 300S.
  3. Confirm the engine: 3.5L V6 SOHC, commonly listed as VIN G on parts sites .
  4. Confirm the assembly type: complete in-tank fuel pump module, not an external pump and not just a bare pump cartridge unless you are deliberately rebuilding the module.
  5. Cross-check the interchange number: E7137M, SP7137M, P74819M, FG0232, Bosch 67663, Autobest F3148A, or the Mopar numbers listed for this application .

Ask the seller these questions before buying:

  1. Does the module include the fuel level sending unit?
  2. Is the tank seal or O-ring included?
  3. Is the pressure regulator included?
  4. Is the outlet the correct quick-connect size and style?
  5. Does the listing cover the 1999 300M 3.5L V6 specifically?
  6. What warranty applies, and is it parts-only or parts-and-labor?

Some listings show a sending unit resistance range around 1050–60 ohms for this application, while others list maximum pressure around 44 PSI and 12V operation . Treat catalog specifications as fitment data, not as a pressure test result for your car. For a repair decision, use a service manual specification and an actual gauge reading.

4. Diagnosis: Test Before You Replace

Replacing the module on this car takes real labor. A careful test sequence can save hundreds of dollars.

1. Listen for pump priming. Turn the key to ON without cranking. Many vehicles run the pump briefly to prime the system. A quiet tank does not prove failure by itself, but a clear hum for a second or two is a good sign.

2. Check fuses and relay. Inspect the fuel pump fuse, ASD/relay circuit, and related power distribution points. Swap a known-good relay only if the part numbers match. Look for heat damage or corrosion in the socket.

3. Check voltage and ground at the module. With the circuit commanded on, a test light or multimeter should show battery voltage and a solid ground. Low voltage from a corroded connector can burn out a new pump early.

4. Measure fuel pressure. Connect a gauge rated for gasoline to the proper service point and compare the reading with the factory service specification. Pressure that is low, drops fast after shutdown, or falls during acceleration supports a fuel delivery fault.

5. Inspect live data and codes. Lean codes, misfires, and crankshaft or camshaft sensor codes can appear alongside fuel problems. Codes point to a direction; they do not replace pressure and electrical testing.

6. Rule out contaminated fuel. Water, dirt, or old gasoline can damage a pump and clog the strainer. If the tank is rusty or contaminated, clean or replace the tank before installing a new module.

7. Consider the fuel gauge separately. If the car runs well but the gauge is wrong, the sending unit, float, wiring, or instrument cluster may be the problem. Because the sender is part of the module, a complete assembly often fixes both fuel delivery and gauge faults .

5. Why the Whole Module Is Usually the Right Repair

On many older cars, owners replaced only the pump motor inside the module. On the 1998–1999 LH-platform cars, the filter and regulator are integrated into the in-tank module, and catalogs describe the replacement as a complete assembly that includes the pump, sender, float, reservoir, strainer, regulator, and seal .

Reasons to choose a complete module:

  1. The regulator and filter are inside the tank. You cannot service the external filter as a separate maintenance item .
  2. The sending unit is old. A 1999 float and resistor card may already be inaccurate.
  3. The plastic reservoir and seals age. Heat, fuel, and mileage make them brittle.
  4. Labor dominates the job. Paying to lower the tank twice costs more than buying a complete assembly once.
  5. Fitment is cleaner. A direct-fit module keeps the factory connector, outlet, lock ring area, and tank opening .

A bare pump can still make sense for an experienced builder who is upgrading a specific pump insert and has already inspected the module. For a daily driver, original-style repair, or first-time DIY job, the complete unit is easier to stand behind.

6. Is There an Access Panel Under the Rear Seat?

Owners often ask whether the pump can be reached from inside the trunk or under the back seat. For this platform, parts guidance states that the fuel tank must be lowered to replace the module, and that is the main reason professional labor is high . Some owners in online forums describe cutting an access hole, but that is not a factory service procedure and can create safety, corrosion, and structural concerns around the fuel tank and body.

Do not cut the floor unless you fully understand the risks. Fuel vapor, sharp metal near hoses and wiring, and an unsealed panel are serious problems. For most owners, the correct method is to support the vehicle, relieve fuel pressure, disconnect the battery, drain or lower the fuel level, disconnect lines and wiring, support the tank, remove the straps, lower the tank, clean the opening, release the lock ring, and lift the module out.

If you do not have a safe lift, jack stands, a transmission jack or tank support, line disconnect tools, and a well-ventilated workspace, this is a job for a shop.

7. Replacement Overview for a Shop or Experienced DIY Owner

The outline below is not a substitute for a factory service manual. It shows the order of work so you can talk intelligently with a mechanic and plan the parts, tools, and time.

1. Reduce fuel level. A full tank is heavy and increases spill risk. Siphon or drive the car down to a low level before the repair.

2. Relieve fuel pressure. Follow the service procedure for the fuel system. Wear eye protection and keep a rated fire extinguisher nearby.

3. Disconnect the negative battery cable. Prevent sparks and accidental priming.

4. Raise and support the car securely. Use jack stands on a level surface. Never rely on a jack alone.

5. Disconnect the fuel lines, vapor lines, and electrical connector. Quick-connect fittings may need the correct release tool. Note the routing before removal .

6. Support the tank and remove the straps. Lower the tank slowly. Watch for hoses or wires still attached.

7. Clean the top of the tank. Dirt must not fall into the tank when the module is removed.

8. Release the lock ring and remove the old module. Avoid bending the float arm. Compare the old and new modules side by side before installation.

9. Install a new seal. Lubricate only as directed by the part maker. A pinched O-ring can cause a fuel smell or evaporative emissions fault.

10. Refit the tank, reconnect all lines, and reinstall straps. Make sure each connector clicks and each line is fully seated.

11. Reconnect the battery and prime the system. Cycle the key several times, then check for leaks before starting.

12. Verify pressure, gauge operation, and road behavior. Recheck for leaks after the first drive and again the next day.

8. Cost, Time, and Parts Choices in the U.S. Market

Replacement cost varies by region, brand, and whether the tank is rusty. One U.S. parts guide estimates $450–$600+ for a new OEM Mopar module, $150–$300 for aftermarket modules from established brands, and $400–$700+ in shop labor, for a typical professional total of $700–$1,100+ . Used OEM modules appear for less, but a used in-tank pump with unknown history is a poor bet when labor is the largest part of the bill.

Typical buying options:

  1. Mopar/OEM: Highest price, original specification, often preferred for a collector car.
  2. Established OE-supplier aftermarket: Delphi, Bosch, Carter, Spectra Premium, Autobest, and similar brands are widely listed for this application .
  3. Budget marketplace assembly: Lowest price, but warranty length, materials, and fitment notes vary. Read the listing closely.
  4. Pump-only insert: Lower part cost, more work, and old sender, regulator, and reservoir remain in the tank.

For a car that is more than 25 years old, also budget for a new lock ring, tank strap hardware, fuel line clips, or a tank cleaning if rust is present. A cheap module installed into a contaminated tank will not last.

9. Brand Recommendation: KEMSO Fuel Pumps

If you are replacing a 99 Chrysler 300M fuel pump and want a part built for dependable fuel delivery, KEMSO is a brand worth considering. KEMSO fuel pumps are designed as high-performance OEM replacement units that meet or exceed factory specifications for fit, flow, and pressure while offering additional flow capacity for upgraded vehicles . The lineup includes direct OEM replacement pumps that drop into the factory location without modification, as well as high-performance options for demanding builds .

Why KEMSO stands out for U.S. buyers:

  1. High-performance construction. KEMSO uses materials intended for the harsh environment inside a fuel tank and motors engineered for consistent pressure delivery and long service life .
  2. OEM replacement fit. The pumps are designed to work with factory mounting, factory wiring, and factory fuel system layouts .
  3. Lifetime warranty. KEMSO states that every fuel pump comes with a lifetime warranty, with serialized pump bodies used on many listings to support the warranty .
  4. Fuel compatibility. KEMSO publishes gasoline, ethanol, and E85 compatibility across parts of its range, which matters in markets where ethanol blends are common .
  5. U.S.-based support. Product information highlights U.S.-based technical support for buyers who need help confirming fitment before installation .

Before ordering, use the site’s fitment tools or contact support with your 1999 Chrysler 300M, 3.5L V6, VIN, and current part number. Confirm that the listing includes the complete module, sending unit, seal, and correct connector for your car. Lifetime warranty coverage is a strong reason to buy once, but the exact application still has to match.

Visit https://www.kemsoracing.com/ to review KEMSO fuel pump options, check fitment details, and contact the brand about the right replacement for your vehicle.

10. How to Make the New Pump Last

A new fuel pump can fail early if the rest of the system is ignored. These habits are simple and practical for an older 300M.

1. Keep the tank above a quarter full when possible. Fuel cools and lubricates the in-tank pump. Repeated low-fuel driving adds heat and makes the pump draw from the bottom of the tank where debris collects. Delphi notes that a larger reservoir helps handle low-fuel situations, but that is not a reason to run the car dry every week .

2. Replace or clean a contaminated tank. Rust, sediment, and water destroy strainers and pump motors.

3. Fix electrical faults. A corroded connector or weak ground causes low voltage and heat at the motor.

4. Use fresh gasoline. If the car sits for months, use a fuel stabilizer approved for your fuel type and follow the product directions.

5. Install a new tank seal. Reusing a flattened O-ring can cause fuel odor and EVAP faults.

6. Verify pressure after installation. A proper reading confirms that the regulator, line, and pump all work together.

7. Keep records. Write down the part number, mileage, date, warranty receipt, and pressure reading. That record helps if a warranty claim or future diagnosis is needed.

11. Frequently Asked Questions

1. Will a 1998 Dodge Intrepid fuel pump fit a 1999 Chrysler 300M?
Some module numbers cover both cars, but the engine and connector must match. The 1999 300M 3.5L V6 appears on cross-reference lists with E7137M, SP7137M, P74819M, FG0232, Bosch 67663, and Autobest F3148A . Always verify by VIN and engine, not by platform name alone.

2. Can I replace just the fuel filter?
On these models, the filter and pressure regulator are integrated into the fuel pump module inside the tank. Parts guidance states there is no separate serviceable filter to replace on its own .

3. How do I know it is not the crank sensor?
A failing crank sensor can cause a no-start, but it will not cause low fuel pressure. Check for spark, injector pulse, RPM signal, and codes. If pressure is out of specification and the pump has correct power and ground, the fuel module is the stronger suspect.

4. Should I buy used?
A used module from a 1990s car has an unknown sender, strainer, regulator, and motor history. With tank-down labor, a new warrantied assembly is usually the better value.

5. Why does my fuel gauge act strange after replacement?
Check the connector, float arm movement, and the resistance range of the sending unit. A wrong module for a different LH-car engine or trim can read incorrectly. Compare the old and new part numbers before closing the tank.

6. What if the car starts but loses power at 60 mph?
That can be low pressure, a restricted strainer, a weak pump motor, a failing regulator, or a dirty tank. A pressure gauge observed under load, not only at idle, is the useful test.

7. Is a lifetime warranty really important on an older car?
Yes, if you plan to keep the vehicle. It reduces the cost of a repeat failure, though you should still read the warranty terms and keep your receipt.

8. Can I drive with a noisy pump?
You may be able to drive short distances, but a noisy or intermittent pump can leave you stranded. If the car stalls, surges, or fails to restart when hot, arrange the repair before a long trip.

12. Final Buying Checklist

Before you pay for a 99 Chrysler 300M fuel pump, make sure you have:

  1. Correct vehicle: 1999 Chrysler 300M, 3.5L V6.
  2. Correct assembly: complete in-tank module with sender, regulator, strainer, and seal.
  3. Verified interchange number: E7137M, SP7137M, P74819M, FG0232, 67663, F3148A, or the matching Mopar reference.
  4. Pressure test result: low or unstable pressure with confirmed power and ground.
  5. Clean tank plan: no rust, water, or heavy sediment left behind.
  6. New seal and any damaged hardware: lock ring, clips, straps, or line fittings as needed.
  7. Written warranty: keep the receipt, part number, and installation record.
  8. Safe installation plan: proper lift support, ventilation, fuel handling, and leak checks.

The bottom line is simple: a 99 Chrysler 300M fuel pump replacement is not a guess-and-swap repair. Confirm the 3.5L V6 fitment, test pressure and electrical supply, replace the complete module with a new seal, and verify the repair before driving. Because the tank has to come down, choose a dependable, warrantied part the first time. For high-performance OEM replacement fuel pumps backed by a lifetime warranty, review the KEMSO lineup at https://www.kemsoracing.com/.

https://www.kemsoracing.com/