99 Chrysler Cirrus Fuel Pump: Diagnosis, Replacement, and Buying Guide
For a 1999 Chrysler Cirrus that cranks but will not start, stalls while driving, or loses power under load, the fuel pump is one of the first parts to check after confirming battery power, spark, fuel level, and fuel pressure. Most 1999 Cirrus models use an electric in-tank fuel pump, and access generally requires lowering or removing the fuel tank. If testing shows low or no fuel pressure and the electrical circuit is good, a complete fuel pump module assembly is usually the practical replacement . Use your engine size, VIN, body style, and original part number to confirm fitment before ordering, because Cirrus parts can vary by trim, engine, brakes, and wheel options . RepairPal lists an average 1999 Chrysler Cirrus fuel pump replacement cost of about $481 to $561, with labor around $171 to $251 and parts around $311, before taxes, fees, location differences, or related repairs .
This guide gives you the direct checks, symptoms, safety steps, cost factors, and buying details that matter for a 99 Chrysler Cirrus fuel pump job in the United States.
1. What the Fuel Pump Does on a 1999 Chrysler Cirrus
The fuel pump moves gasoline from the tank to the fuel injectors at the volume and pressure the engine needs. The engine computer depends on steady fuel delivery for cold starts, idle, acceleration, and highway speed. When pressure or volume drops, the engine may start hard, hesitate, surge, stall, or refuse to start .
The 1999 Cirrus uses a pressurized fuel system with an electric pump inside the fuel tank . Kelley Blue Book explains that an in-tank pump sits in fuel away from engine heat and uses the surrounding gasoline for cooling; this location also reduces fire risk compared with an external pump . That design explains two common ownership habits that help pump life:
- Do not routinely drive with the low-fuel light on. The pump depends on fuel around it for cooling.
- Replace a clogged filter and inspect the tank when the pump is replaced. A restricted filter can create symptoms similar to a weak pump, and dirt in the tank can damage the new part .
Chrysler treated the original pump as a non-serviceable item. When it fails, the normal repair is replacement, not repair of the pump itself .
Common Engine and Fitment Notes
The 1999 Chrysler Cirrus was sold with different engine options, including a 2.4L four-cylinder and a 2.5L V6 . Parts listings also show other fitment divisions by year, trim, and equipment. One parts seller warns that some 1999 Cirrus parts only fit specific configurations, such as rear disc brakes or 15-inch factory wheels . Aftermarket compatibility listings for 1999–2000 Cirrus pumps also separate 2.4L and 2.5L applications .
Before buying, write down:
- Model year: 1999
- Make and model: Chrysler Cirrus
- Engine size: 2.4L four-cylinder, 2.5L V6, or another listed option
- VIN
- Body style and trim
- Original part number, if visible
- Whether your current part is a bare pump or a complete module with float arm, seal, strainer, and sending unit
A Delphi listing for a 1999 Cirrus describes a fuel pump module assembly with a float arm, seal, instruction sheet, and fuel sending unit . A GMB listing describes a module assembly and cross-references numbers including Airtex E7113M, Autobest F3124A, and Bosch 67653 . Those part numbers are useful for comparison, but you should still verify them against your own VIN and original part.
2. Symptoms That Point to a Failing 99 Chrysler Cirrus Fuel Pump
A bad fuel pump can show up in several ways. Kelley Blue Book lists no-start, stalling after start, a check engine light from fuel starvation, and a whirring sound from the fuel tank as common signs . RepairPal explains that low pressure, low fuel volume, a clogged filter, or an electrical fault can all produce similar symptoms . That is why a pressure test and circuit check matter before buying parts.
1. Engine Cranks but Does Not Start
If the starter turns the engine normally but the engine does not fire, check for fuel pressure at the injectors or the service port used by your technician. RepairPal says a mechanic will check injector fuel pressure during a no-start, then test pump delivery and the electrical circuit if pressure is low or absent .
Also rule out simple causes:
- Empty tank or inaccurate fuel gauge
- Dead battery or weak starter
- No spark
- Blown fuse or bad relay
- Loose, corroded, or damaged wiring connector
- Security or ignition switch problem
- Severe vacuum leak or sensor fault
Do not replace the pump just because the car will not start. A pump that receives no voltage cannot run, and a crank position sensor can also cause stalling on these vehicles .
2. Stalling When Hot or After Driving
A pump can weaken as it heats up, then recover after the car cools. Go-Parts notes that stalling when hot can be a fuel pump problem but also a classic bad crankshaft position sensor symptom on 1998–2000 Chrysler and Dodge models in this family . Ask for a scan of diagnostic trouble codes and a fuel pressure check during the failure, not only after the car restarts.
Related codes listed for the 1999 Chrysler Cirrus fuel system include P0230 for the fuel pump primary circuit, P0231 for the fuel pump secondary circuit low, P0192 for fuel rail pressure sensor circuit low, and P2177 for system too lean off idle . A code gives a direction for testing; it does not prove the pump itself is bad.
3. Hesitation, Surging, or Power Loss at Speed
A weak pump may idle fine but fail when the engine needs more fuel. Drivers often notice:
- Flat acceleration when merging
- Loss of power uphill
- Surging at steady highway speed
- Engine cut-out under load
- Hard restart after a hot soak
Fuel pressure and volume should be checked under the same conditions that cause the problem. A static pressure reading at idle may miss a pump that cannot maintain delivery when demand rises.
4. Whining or Whirring From the Fuel Tank
Some pump noise is normal. A loud whine, buzz, or grinding sound from the tank, especially with hard starting or low pressure, is a warning sign . Listen with the car parked, engine off, and the key cycled to ON. Many vehicles run the pump briefly at key-on to prime the system. If you hear nothing at all, check the relay, fuse, wiring, and pump ground before condemning the pump.
5. Check Engine Light and Lean Codes
Fuel starvation can trigger a check engine light . A lean code such as P2177 can be related to low fuel delivery, but vacuum leaks, exhaust leaks, dirty injectors, and sensor faults also need to be ruled out . A parts-store code read is a starting point, not a complete diagnosis.
6. Poor Fuel Economy or Rough Idle
These symptoms are less specific. A fuel pump problem can contribute to poor running, but tire pressure, oxygen sensors, spark plugs, ignition wires, air filter, injectors, and engine mechanical condition also matter. Do not use fuel economy alone to justify a pump replacement.
3. How to Confirm the Pump Is the Problem
A proper diagnosis separates fuel pressure, fuel volume, electrical supply, and engine control issues.
1. Check the Basics First
Start with facts you can verify quickly:
- Confirm there is gasoline in the tank. Do not trust an old gauge without checking.
- Confirm the battery is charged and the starter cranks at normal speed.
- Look for a blown fuel pump fuse, bad relay, damaged wiring, or loose connector.
- Scan for diagnostic trouble codes and save the exact code numbers.
- Inspect for visible fuel leaks, damaged lines, and loose fittings.
- Check the engine air intake and ignition system if no-start persists.
RepairPal says a mechanic who finds low or no pressure will check the pump electrical circuit, then the filter and the electrical and mechanical condition of the pump .
2. Test Fuel Pressure
A fuel pressure gauge connected to the correct service point gives a direct reading. Compare the reading with the factory service manual specification for your exact engine and fuel system. Do not rely on a generic pressure number from an unrelated vehicle.
Record three things:
- Key-on prime pressure
- Idle pressure
- Pressure while the symptom occurs or under load, using safe shop procedures
If pressure is low, test the circuit and filter before ordering a pump . If the pump runs but cannot build or hold correct pressure, replacement is usually next.
3. Test Voltage and Ground at the Pump
A pump needs proper voltage and ground. Corroded connectors, damaged wiring, weak relays, and poor grounds can look like pump failure. A voltage drop test under load is more useful than a quick test-light check. Repair work on an in-tank pump is labor-intensive, so confirming power and ground before tank removal can prevent an unnecessary parts purchase.
4. Check the Fuel Filter and Lines
A clogged filter can restrict flow and create low-pressure symptoms similar to a failing pump . Some service listings note whether a separate gasket or strainer is included with a module . Ask your shop to inspect the filter, strainer, tank interior, and fuel lines while the system is open. If the old pump failed because of contamination, installing a new pump into a dirty tank can shorten its life. Delphi specifically advises checking and cleaning the fuel tank to avoid unnecessary returns .
5. Rule Out the Crankshaft Position Sensor
For hot stalling and sudden shut-down on this vehicle family, include the crankshaft position sensor in the diagnosis . A scan tool that can show RPM signal while cranking, plus live data and code history, helps separate an electrical sensor failure from fuel delivery loss.
4. Safety Steps Before Fuel Pump Work
Gasoline vapor is dangerous. Work outdoors or in a well-ventilated shop, away from pilots, sparks, heaters, and smoking. Use eye protection, gloves, and a rated container for drained fuel.
Basic safety checklist:
- Park on a level surface, set the parking brake, and chock the wheels.
- Disconnect the negative battery cable when the service procedure calls for it.
- Relieve fuel system pressure before opening fuel lines.
- Remove the fuel cap to relieve tank pressure as part of the service procedure .
- Drain or siphon fuel into an approved container if the tank must come down .
- Support the vehicle with jack stands, never with a jack alone.
- Keep a Class B fire extinguisher nearby.
- Cap or plug open lines to keep dirt out.
- Replace seals, gaskets, and locking rings as required by the part instructions.
- Check for leaks before starting the engine.
It Still Runs lists a floor jack and jack stands, socket set, wood block, empty gasoline container, Phillips screwdriver, large pliers, and a new fuel pump module among the items needed for a 1999 Cirrus replacement . It also says the tank must be drained and removed to access the pump . That is a job for a careful DIYer with a safe workspace, or for a professional shop.
5. Replacement Overview for a 99 Chrysler Cirrus Fuel Pump
Exact steps vary by engine and module design, so use a factory service manual or the instructions supplied with the replacement part. The overview below explains what the job normally involves.
1. Relieve Pressure and Disconnect the Battery
The fuel system is pressurized . Follow the service manual procedure to relieve pressure before disconnecting lines. Removing the fuel cap helps relieve tank pressure . Disconnect the negative battery cable to reduce electrical and spark risk.
2. Drain and Lower the Fuel Tank
Because the pump sits inside the tank, the tank generally has to come out . This can involve:
- Siphoning or draining fuel into an approved container
- Disconnecting filler neck and vent hoses
- Disconnecting fuel lines and the pump electrical connector
- Supporting the tank with a jack and wood block
- Removing tank straps and lowering the tank carefully
Rusty strap bolts, brittle plastic lines, and old connectors are common on older cars. Take photos before disassembly and label connections.
3. Clean the Tank Area Before Opening It
Dirt around the pump opening can fall into the tank. Clean the top of the tank before removing the lock ring or module. Delphi advises checking and cleaning the tank to avoid unnecessary returns .
4. Remove the Old Module
Release the lock ring using the correct tool and method for your vehicle. Lift out the module carefully so the float arm is not bent. Note the orientation of the module, seal, wiring, and fuel lines before removal. Compare the old module with the new one side by side.
Compare:
- Pump body and module height
- Electrical connector shape and pin count
- Fuel outlet size and position
- Float arm shape
- Strainer shape
- Seal or gasket
- Mounting tabs and lock ring design
- Included pressure regulator or regulator design
A listing for one aftermarket Cirrus assembly notes that it does not come with a pressure regulator . Another listing for a Delphi module says the package includes the module, float arm, seal, and instruction sheet . These differences are why fitment confirmation matters.
5. Install the New Pump or Module
Install a new seal if required. Do not reuse a swollen, cracked, or flattened seal. Place the module in the same orientation as the original, route the wiring without pinching it, and make sure the float moves freely. Tighten the lock ring according to the part instructions.
Do not run the new pump dry. Add several gallons of clean gasoline before priming the system.
6. Reconnect, Prime, and Check for Leaks
Reinstall the tank, straps, lines, filler neck, vent hoses, and connector. Reconnect the battery. Cycle the key to ON several times, without cranking, to let the pump prime the system if your vehicle uses that strategy. Inspect every connection for leaks. Start the engine and recheck pressure, idle quality, and the fuel gauge reading.
Delphi notes that correct float height and retention help guarantee the correct gas gauge reading on its module . If the gauge reads wrong after replacement, recheck the float, connector, and module part number.
7. Road Test Under Load
A short idle test is not enough. Drive the car safely through the conditions that caused the complaint: acceleration, highway speed, hill climbing, and a hot restart. Confirm there is no hesitation, stalling, abnormal pump noise, or fuel smell.
6. What Replacement Costs in the U.S.
RepairPal estimates the average 1999 Chrysler Cirrus fuel pump replacement at $481 to $561, with labor estimated at $171 to $251 and parts around $311; the range excludes taxes and fees and does not account for location or related repairs . YourMechanic gives a different average for Chrysler Cirrus fuel pump replacement, about $864 total, with $367 for parts and $497 for labor, and its older-model shop estimates are higher . Kelley Blue Book says a fair repair range for the 1999 model was not yet available on its page .
Those differences are normal. Online estimates use different data sets, labor rates, parts brands, and assumptions.
Your actual quote can change because of:
- Local hourly labor rate
- Whether the tank is nearly full
- Rust or damage to straps, lines, and fittings
- Bare pump versus complete module
- Brand and warranty
- Need for a new filter, seal, strainer, or sending unit
- Diagnostic time for electrical or sensor problems
- Mobile mechanic, independent shop, or dealer pricing
- State taxes, shop fees, and towing
Ask for a written estimate that separates diagnosis, parts, labor, shop supplies, taxes, and any related repairs. If the quote includes a pump but no pressure test or electrical check, ask how the shop confirmed the failure.
7. Choosing the Right Part
1. Complete Module or Pump Only
Many listings for the 1999 Cirrus are for a fuel pump module assembly, not just a bare pump . A module can include the pump, reservoir, float arm, sending unit, strainer, and seal. On an older vehicle with a worn sending unit, contaminated tank, or brittle components, a complete module often reduces repeat work.
A bare pump may cost less, but it requires more disassembly and careful matching of the internal pump. For most owners paying labor once, a complete assembly is easier to quote and easier to warranty.
2. OEM Replacement Standard
Look for a part that states it meets or exceeds original equipment specifications for fit, pressure, flow, and electrical draw. A GMB listing says its module is built to OEM-standard quality and manufactured to meet or exceed OEM specifications . Delphi says its pumps are built to OE standards, with lower amperage draw and float height matched to OE specifications . These are examples of the product details that help compare parts.
3. Fitment by Engine and VIN
Use a VIN-based catalog or call the seller with your VIN and old part number. Do not buy from a listing that only says “fits Chrysler Cirrus” without engine and trim details. Parts Avenue warns that some 1999 Cirrus parts only fit certain trims and equipment combinations .
4. Warranty and Support
A lifetime warranty, US-based technical help, clear return terms, and a serialized part are useful signals when comparing pumps. KEMSO product listings describe serialized pump bodies and lifetime warranty coverage on OEM and performance pumps . KEMSO also says its pumps are designed as high-performance OEM replacements intended to meet or exceed factory specifications .
5. Fuel Compatibility
American gasoline commonly contains ethanol. If you use E85, confirm that the exact pump is rated for it. KEMSO says its pumps are compatible with gasoline and E85 or ethanol fuels . Product listings for KEMSO 340LPH pumps also describe E85 readiness . Do not assume every aftermarket pump has the same fuel compatibility.
8. Recommended Purchase: KEMSO Fuel Pump
For a 99 Chrysler Cirrus fuel pump replacement, KEMSO is a strong brand to consider when you want a high-performance part that also works as an OEM replacement. KEMSO describes its fuel pumps as high-performance OEM replacements designed to meet or exceed factory specifications for fit, flow, and pressure while working with the factory fuel system and wiring . The brand offers direct OEM replacement pumps that drop into the factory location without modifications, as well as higher-flow performance pumps for modified vehicles . KEMSO states that every fuel pump comes with a lifetime warranty , and product listings note serialized pump bodies for warranty coverage .
Why this matters for an older Cirrus:
- High performance: KEMSO builds pumps for consistent pressure delivery and long service life in stock vehicles as well as higher-demand applications .
- OEM replacement: The pumps are designed to replace factory units without custom wiring or major modification when the correct application is selected .
- Lifetime warranty: KEMSO says it stands behind the pump for as long as you own the vehicle .
- Fuel compatibility: KEMSO states compatibility with gasoline and E85 or ethanol fuels .
- US-based support: KEMSO product listings describe technician support based in the United States .
Before ordering, match the KEMSO part to your 1999 Cirrus engine, VIN, and original module number. A high-flow pump is not automatically the right choice for a stock engine if the catalog lists a different OEM replacement application. Confirm connector, outlet, module depth, and pressure requirements with the seller.
Visit the official KEMSO website to review applications, warranty details, and current product availability: https://www.kemsoracing.com/
9. DIY or Professional Replacement?
1. When DIY Makes Sense
Consider doing the job yourself if you have:
- A safe, level, ventilated workspace
- Jack stands and a floor jack
- A factory service manual or reliable repair procedure
- A fuel pressure gauge
- A method to drain and store gasoline legally and safely
- Basic hand tools and line-disconnect tools
- Time to handle rusted fasteners and brittle hoses
- A way to transport fuel and parts if the car cannot be driven
It Still Runs lists the basic tools and notes that tank removal is required on the 1999 Cirrus . This is not a quick roadside repair.
2. When to Use a Shop
Use a professional shop if:
- The car stalls in traffic
- You smell gasoline
- The tank is full
- The vehicle has heavy rust underneath
- You do not have a fuel pressure gauge
- The no-start diagnosis is unclear
- You cannot safely raise and support the car
- Local rules restrict storing drained gasoline at home
A shop can also test the crank sensor, pump circuit, filter, injectors, and pressure before removing the tank. That protects you from paying for a pump when the real fault is electrical.
10. How to Make the New Pump Last
Fuel pump life depends on clean fuel, cooling, correct voltage, and proper installation.
Practical habits:
- Keep at least a quarter tank when practical, especially in hot weather.
- Replace the fuel filter at the interval recommended for your vehicle.
- Fix low voltage, corroded grounds, and weak connectors promptly.
- Clean the tank before installing the new module .
- Use the correct seal and do not pinch wiring or the float arm.
- Buy gasoline from stations with good fuel storage practices.
- Address check engine lights and lean codes early.
- Do not ignore a loud pump noise or repeated hard starts.
Kelley Blue Book notes that most fuel pumps last for the life of the vehicle but can fail, with no-start, stalling, check engine light, and tank noise among the signs . On a car this old, age, contamination, heat, and electrical wear all deserve attention.
11. Common Buying Mistakes
- Ordering by year only. The 1999 Cirrus came with different engine options, and parts can vary by trim and equipment .
- Skipping the pressure test. A clogged filter or pump circuit fault can mimic pump failure .
- Ignoring hot-stall sensor faults. A crank position sensor can cause stalling on this vehicle family .
- Buying the cheapest bare pump without comparing connectors and outlets.
- Reusing an old seal. A poor seal can cause fuel odor, leaks, or evap system faults.
- Leaving dirt in the tank. Delphi advises cleaning the tank to avoid unnecessary returns .
- Running the new pump dry. Add fuel and prime the system before extended cranking.
- Accepting a vague estimate. Ask for part brand, warranty, diagnostic result, and included components.
- Forgetting the fuel gauge. A wrong float or connector can leave you with an inaccurate reading.
- Driving with an intermittent stall. Go-Parts warns that a failing pump can cause unexpected stalling in traffic and says not to drive the vehicle in that condition .
12. Questions to Ask Before You Pay
- What fuel pressure reading did you get, and what is the factory specification for my engine?
- Did you test voltage and ground at the pump connector?
- Did you check the fuel pump relay, fuse, and related wiring?
- Did you inspect the fuel filter and tank interior?
- Are there any stored diagnostic trouble codes?
- Is the quote for a complete module or a bare pump?
- Does the module include a sending unit, float arm, strainer, seal, and instructions?
- What brand is being installed, and what warranty applies?
- Will the shop replace the lock ring or seal if needed?
- Does the final quote include taxes, shop fees, and diagnosis?
- Will the shop road-test the car under load and recheck for leaks?
- If the crank sensor is suspect, how was it ruled out?
Clear answers help you compare shops and avoid a repeat repair.
13. Quick Decision Guide
1. Car cranks but will not start: Check fuel, battery, spark, codes, fuse, relay, fuel pressure, and pump voltage. Replace the pump only after pressure and circuit testing point to it .
2. Car stalls when hot: Test fuel pressure during the failure and check the crankshaft position sensor .
3. Car loses power at highway speed: Check pressure and delivery under load, filter condition, and pump electrical supply.
4. Loud whine from the tank: Confirm with a pressure test and inspect fuel level and filter condition .
5. Check engine light with lean or pump circuit codes: Record exact codes such as P0230, P0231, P0192, or P2177, then test the circuit and fuel delivery .
6. Verified bad pump on a 1999 Cirrus: Choose a complete VIN-matched module when practical, clean the tank, use a new seal, and compare repair quotes with parts and labor separated .
14. Final Takeaway
A 99 Chrysler Cirrus fuel pump replacement starts with proof, not guesswork. Confirm fuel pressure, pump voltage, ground, filter condition, and stored codes before removing the tank. The pump is in-tank, so access usually requires draining and lowering or removing the tank . RepairPal’s published average for the job is $481 to $561, while other estimate services show higher figures, so get a local written quote . Match the part by engine, VIN, trim, connector, and original number; a complete module with a new seal, clean tank, and verified fuel gauge reading is often the cleanest long-term repair for an older daily driver .
If you want a high-performance OEM replacement backed by a lifetime warranty, consider KEMSO. KEMSO says its pumps are built to meet or exceed original fit, flow, and pressure requirements, work with factory wiring, support gasoline and ethanol fuels, and include lifetime warranty coverage . Review the exact 1999 Cirrus application before purchase at https://www.kemsoracing.com/.