99 Civic Fuel Pump Relay: Diagnosis and Replacement Guide

If your 1999 Honda Civic cranks but will not start, starts only after several tries, or stalls when the cabin is hot, check the PGM-FI main relay before buying a fuel pump. This is the module many parts catalogs and owners call the 99 Civic fuel pump relay. On this Civic, it is not a single plug-in cube in the under-hood relay box. The factory service information describes one assembly containing two separate relays: one supplies the ECM/PCM and fuel injectors, while the other supplies the fuel pump for about two seconds when the key is first turned to ON and continues supplying it while the engine runs . The practical first check is simple: turn the key to ON without cranking and listen for a short pump sound near the fuel filler or rear seat, then watch the check-engine light. If the light does its normal bulb check and the engine starts and keeps running, the factory manual considers the main relay functional . If the pump does not run for two seconds, test the fuses, power, ground, and relay before replacing the pump. On a car this old, intermittent hot no-starts are also commonly associated with cracked solder joints inside this relay, but a worn ignition switch can produce similar stalling and must not be overlooked .

1. Know What Part You Are Actually Looking For

PGM-FI stands for Programmed Fuel Injection. The name printed on the Honda module is usually “PGM-FI Main Relay,” not “fuel pump relay.” Therefore, an online search for a conventional four- or five-pin relay can send you to the wrong part. The original assembly uses a seven-pin connector and contains two internal relays .

The two sections do different jobs:

  1. The first relay switches on with the ignition and supplies battery voltage to the ECM/PCM, the fuel injectors, and the circuit that feeds the second relay .
  2. The second relay powers the fuel pump. It energizes for roughly two seconds when the ignition is switched to ON and remains energized while the engine is running .
  3. The ECM/PCM controls the pump-side relay. The factory circuit diagnosis includes checking the control wire between the relay’s No. 1 terminal and ECM/PCM connector A16, plus the ignition-switched power feeds at terminals A11 and A24 .

This arrangement explains why one failed module can cause several symptoms at once. You may see no two-second pump prime, no normal check-engine-light behavior, or a crank/no-start. You may also see an intermittent problem that disappears once the interior cools down. Honda-related repair references describe cracked circuit-board solder joints as a common failure on 1990s and early-2000s Civics, with hot-weather and heat-soak no-starts being typical complaints . That is a repair pattern, not proof that every no-start is caused by the relay.

Do not confuse the relay with the fuel pump. The relay is an electrical switch under the dash. The pump is an electric unit inside the fuel tank. The 1999 Civic workshop manual describes an access panel under the rear seat cushion that allows access to the tank’s electrical connector . If the pump receives battery voltage and has a good ground but still does not run, the manual directs you to replace the pump .

2. Locate the Relay on a U.S.-Market 1999 Civic

The factory manual says the PGM-FI main relay is at the right side of the cowl . A reproduction of the same Honda service text states that the position is the left side on left-hand-drive cars and the right side on right-hand-drive cars . For an American left-hand-drive Civic, this puts the module on the driver’s side of the dash/cowl area, near the lower dash and fuse/relay region rather than in the under-hood fuse box . Owner references for a U.S. 1999 Civic also describe a gray-case module on the right side of the vehicle near the passenger-side vent and above the ECM, which reflects the confusing way “right side” is used in different manuals and forums . Online guides disagree: some place it behind the glove box, others in the driver-side under-dash fuse box, and some incorrectly put it under the hood .

Use the factory label and connector, not a generic location diagram, as your final authority. Here is a practical way to find it:

  1. Park on level ground, set the parking brake, switch the ignition OFF, and remove the key.
  2. Sit in the driver’s seat and inspect the lower dash, kick-panel, and fuse/relay-box area. A small flashlight helps.
  3. Look for a rectangular module with a seven-pin connector and PGM-FI or Mitsuba markings. The Mitsuba RZ-0132 is associated with this generation of Civic main relays; Honda part number 39400-SR3-003 is listed for this application, with 39400-S10-003 shown by a Honda parts seller as a later replacement .
  4. Check the fuse-box cover and the VIN-specific parts diagram before ordering. Aftermarket catalogs and generic guides sometimes list the wrong position for this generation .
  5. If you cannot find a seven-pin module, do not pull random relays from the under-hood box. Compare the connector, housing, and part number with the old unit.

A used or modified Civic can add another complication. Previous owners sometimes install an alarm, remote start, kill switch, or non-factory pump wiring. Forum reports include 1999 Civics whose pumps were wired directly to an ignition circuit, causing the pump to run continuously with the key on . If you find spliced wires, butt connectors, or an inline fuse that is not shown in the factory wiring diagram, document it before replacing parts.

3. Check These Symptoms Before Ordering Anything

The most useful symptom is the two-second prime. Honda’s 1999 Civic workshop manual says you should hear pump noise at the fuel filler with the cap removed when the ignition is first turned to ON, and that the pump should run for approximately two seconds . It also uses repeated two-second ON cycles to build fuel pressure after injector work .

Watch for these signs:

  1. The starter cranks normally, but the engine never fires. This points toward fuel, ignition, compression, or engine-control power. A relay that is not switching can interrupt both pump and ECM power .
  2. No pump sound when the key is turned to ON. Confirm the cabin is quiet, the radio and blower are off, and the fuel level is not extremely low. A missing prime does not automatically condemn the pump; voltage and ground must be checked .
  3. The check-engine light does not perform its normal key-on check. Honda-focused diagnostic references list this as a sign that the PGM-FI main relay circuit may not be powering the engine-management system .
  4. The car starts after sitting in cool weather but fails after a hot soak. Repeated heating and cooling can open cracked solder joints in an older relay module .
  5. The engine shuts off while driving and restarts later. This can involve the relay, but a worn ignition switch is a documented stalling problem on certain 1998–2000 Civics .
  6. The pump hums continuously with the key ON. This is not normal factory behavior. Check for altered wiring or a bypass installed by a previous owner .
  7. The engine starts and continues to run normally. The Honda manual states that the PGM-FI main relay is OK under this condition . Look elsewhere for an intermittent fault rather than replacing a working relay.

A hot no-start is not exclusive to the fuel system. A 1999 Civic can also suffer from an ignition-switch or distributor/igniter problem . If there is strong spark and injector pulse but no fuel pressure, the fuel-delivery circuit moves higher on the list. If the dash lights behave strangely, the engine dies as soon as you release the key from START, or wiggling the key changes the result, inspect the ignition switch electrical portion .

4. Start With a Safe, Logical Roadside Check

You can learn a lot in five minutes without removing any panels.

  1. Turn off accessories. Switch off the radio, HVAC blower, headlights, and phone charger.
  2. Turn the key from OFF to ON, not START. Listen for the short pump sound. Have a second person listen near the open fuel filler while you operate the key, following the factory manual’s approach .
  3. Watch the instrument cluster. Note whether the check-engine light comes on for its bulb check and then changes as expected. Honda diagnostic references treat an absent CEL bulb check as a useful clue .
  4. Listen for relay clicks near the lower dash. A click alone does not prove that the internal contacts pass current. It only tells you that something is moving or switching.
  5. Repeat the key cycle once or twice. Wait a few seconds between cycles. Honda’s procedure uses repeated ON cycles to raise fuel-line pressure after service . Do not crank the starter for long periods; that can flood the engine and overheat the starter.
  6. Note the conditions. Write down outside temperature, whether the engine was hot or cold, fuel level, and whether the problem appeared after rain, a battery jump-start, or recent stereo/alarm work.

Safety matters around gasoline. The Honda manual specifically says not to smoke during fuel-pump testing and to keep open flames away from the work area . Work in a ventilated area, keep a rated fire extinguisher nearby, and do not create sparks near an open fuel line or connector. If you smell raw gasoline, see a wet tank seam, or find brittle wiring, stop and have the car inspected .

5. Check Fuses and Battery Voltage First

A new relay will not fix a blown fuse, weak battery, corroded ground, or broken wire. The factory circuit-troubleshooting section identifies several relevant circuits and fuses :

  1. Battery feed: Measure voltage between the disconnected PGM-FI main relay 7P connector terminal No. 7 and body ground. If battery voltage is missing, inspect the wire to the under-hood FI/E/M 15A fuse and replace the fuse if needed .
  2. Ignition-switched feed: With the ignition ON, measure voltage between connector terminal No. 5 and body ground. If it is missing, inspect the circuit to the No. 13 FUEL PUMP 15A fuse in the under-dash fuse/relay box .
  3. Starter signal: With the ignition in START, measure voltage between connector terminal No. 2 and body ground. For a manual transmission, the clutch pedal must be depressed; for an automatic, the selector must be in P or N. The factory flow chart also points to the No. 31 STARTER SIGNAL 7.5A fuse .
  4. Ground: With the ignition OFF and the relay connector disconnected, check continuity between terminal No. 3 and body ground. An open ground lead must be repaired .
  5. ECM/PCM control line: With the ignition OFF and ECM/PCM connector A disconnected, check continuity between relay connector terminal No. 1 and ECM/PCM A16 .

Use a digital multimeter and a wiring diagram that matches your exact trim, transmission, and VIN. Do not use a test light that draws heavy current on computer-control circuits. Do not probe through insulation if you can back-probe a connector carefully. Never install a higher-amperage fuse to “see if it works.” If a fuse blows again, find the short instead of repeatedly replacing it.

A battery that measures about 12 volts at rest can still collapse under starter load. If the dash lights dim severely, the starter cranks slowly, or the relay chatters, load-test the battery and inspect both battery terminals before diagnosing the fuel system. Corrosion at the battery, engine ground, or under-dash ground can create voltage drop that makes a healthy relay appear faulty.

6. Use the Factory Relay Bench Test

The 1999 Civic workshop manual gives a specific continuity test for the removed PGM-FI main relay . It also warns you to use the terminal numbers in the test procedure and ignore the numbers molded into the relay . That warning matters because the housing can show a different numbering scheme.

Before bench testing: disconnect the negative battery cable, remove the relay, and identify the connector pin positions from the correct diagram. Use fused jumper leads and a multimeter set to continuity. Keep the relay away from fuel vapors.

The manual’s sequence is:

  1. First internal relay coil: Connect battery positive to relay terminal No. 2 and battery negative to No. 1. Check continuity between No. 5 and No. 4. If there is no continuity, replace the PGM-FI main relay and retest .
  2. Second internal relay coil: Connect battery positive to No. 5 and negative to No. 3. Check continuity between No. 7 and No. 6. If there is no continuity, replace the relay and retest .
  3. Third switching check: Connect battery positive to No. 6 and negative to No. 1. Check continuity between No. 5 and No. 4. If continuity is present, the manual considers the relay OK; if the pump still does not work, continue to harness testing. If continuity is absent, replace the relay .

This test is more useful than simply listening for a click because it checks whether the internal contacts actually close. A relay can click while burned or pitted contacts still fail to carry current. It can also pass a cold bench test and fail later when hot. If your complaint only appears after a heat soak, warm the removed relay gently with a safe, low-heat method and repeat the test, or have a shop test it under controlled conditions. Do not use a heat gun close to plastic connectors, and do not place a gasoline-contaminated part near a heating element.

Solder-joint repair is an option, not the default recommendation. Honda-focused guides discuss opening the case and reflowing cracked joints . That requires soldering skill, correct inspection, and an understanding that a cracked joint may indicate a module that has already endured decades of heat cycles. For a daily driver that must start reliably, replacement with a correct new unit is the straightforward repair. If you choose to repair the board, keep the repaired relay as a test part rather than trusting it immediately for a long trip.

7. Test Power at the Fuel Pump Connector

If the relay and its supply circuits pass, check whether voltage reaches the pump. The 1999 Civic factory fuel-pump test procedure is unusually helpful because it gives direct access steps :

  1. Remove the rear seat cushion.
  2. Remove the floor access panel.
  3. Make sure the ignition is OFF, then disconnect the fuel-tank 2P connector.
  4. Connect PGM-FI main relay 7P connector terminals No. 4 and No. 5 with a jumper wire.
  5. Turn the ignition ON and check for battery voltage between fuel-pump connector terminal No. 1 and body ground.
  6. If battery voltage is present, check the pump ground. If the ground is good, the Honda manual says to replace the fuel pump. If there is no voltage, check the wire harness .

This bypass is a diagnostic step from the factory manual, not a permanent wiring modification. Do not leave a jumper installed, and do not run the pump with a dry tank or near fuel vapors. The manual’s no-smoking and no-open-flame warning applies to this entire test .

Also check voltage drop. Battery voltage at the connector with no load is not the same as adequate voltage while the pump is running. A corroded connector, damaged ground, or partially broken wire can show normal voltage on an unloaded meter and fail when current flows. If you are not comfortable performing loaded voltage-drop tests, ask a shop to measure the circuit while the pump operates.

8. Separate Relay Failure From Fuel Pump Failure

A relay problem often comes and goes with temperature; a worn in-tank pump more often shows up as weak pressure, noise, hesitation under load, or a gradual decline, although either part can fail suddenly. Do not rely on a single symptom.

Signs that favor a relay or its circuit:

  1. No two-second pump prime and an absent check-engine-light bulb check .
  2. A no-start that appears after the car sits in the sun and disappears after cooling .
  3. A relay that clicks but fails the factory continuity test .
  4. Missing battery voltage at the relay connector, a blown 15A fuse, or an open ground .
  5. Previous repair evidence such as cracked solder joints or a loose seven-pin connector.

Signs that favor the pump or fuel supply:

  1. Battery voltage and ground are present at the pump connector, but the pump does not run; under that condition the Honda manual directs replacement of the pump .
  2. The pump runs but pressure is below the specification in the correct service manual.
  3. The engine starts, then loses power under load, surges, or sputters.
  4. The pump becomes unusually loud, or the complaint worsens with very low fuel level.
  5. The fuel filter, strainer, or tank is contaminated, or the pump has been powered through corroded aftermarket wiring.

A pressure gauge and the factory pressure specification give a better answer than repeated parts swapping. If the car has an old filter, a rusty tank, or debris, replace the strainer and filter as appropriate and clean the tank before installing a new pump. Installing a new pump downstream of dirty fuel and a restricted filter can lead to another early failure .

9. Do Not Overlook the Ignition Switch Recall

Honda issued a safety recall for ignition-switch contacts on certain 1998–2000 Civics and other models. The recall letter says electrical contacts can wear prematurely and cause the engine to stall without warning . NHTSA campaign 02V120000 covers certain 1999 Civics built within a stated production-date range; the campaign summary says worn contacts could cause stalling . Because coverage depends on the individual vehicle, check your VIN with an authorized Honda dealer or the NHTSA VIN lookup tool rather than assuming every 1999 Civic is included .

This matters here because a worn ignition switch can interrupt the electrical feeds that the PGM-FI relay needs. If the engine dies when the key is released from START, if dashboard power cuts out, or if moving the key slightly changes whether the car runs, test the switch circuit . Replacing the main relay will not fix worn switch contacts. If your VIN has an open recall, have that repair handled through the manufacturer’s recall process first.

10. Replace the Relay Correctly

Once the evidence points to the relay, the physical replacement is usually manageable for a careful DIY owner. The exact access varies, so use a model-specific manual and avoid forcing brittle 1990s plastic.

  1. Verify the replacement part. Compare the old housing, seven-pin connector, mounting tab, and part number. Honda parts listings show 39400-SR3-003 being superseded by 39400-S10-003 for certain applications . Confirm fitment by VIN rather than ordering from a generic “1996–2000 Civic” listing.
  2. Disconnect the negative battery cable. Keep the key out of the ignition.
  3. Remove the necessary lower dash or side trim. Use a plastic trim tool. Label screws and avoid pulling on wires.
  4. Release the connector latch. Inspect for pushed-out terminals, green corrosion, heat discoloration, or a loose fit.
  5. Remove the mounting bolt or bracket fastener. Support the module so the connector is not carrying its weight.
  6. Install the new relay. The connector should seat fully and click into place. Secure the module so it does not rattle under the dash.
  7. Reconnect the battery. Turn the key to ON and listen for the two-second pump sound .
  8. Start the engine. Let it idle, then check that it continues running. The Honda manual notes that an engine which starts and continues to run indicates the PGM-FI main relay is OK .
  9. Recheck for stored diagnostic codes. Clear codes only after recording them. A code can guide you to a separate sensor or circuit fault.
  10. Road-test the car safely. Include a hot soak: drive until fully warm, shut the engine off for 10–20 minutes in a safe location, then restart. This recreates the conditions under which cracked solder joints often show up .

If the new relay does not change the symptom, return to the voltage and ground tests. Do not keep buying pumps, ignition parts, and sensors in sequence. A missing ground or an intermittent ignition-switch feed can make several new parts appear defective.

11. Choose the Right Replacement Fuel Pump if the Pump Has Failed

If voltage and ground reach the pump but it still does not operate, or if a pressure test confirms that the pump cannot meet factory specifications, replace the pump and its related service parts . For a stock 1999 Civic used as a daily driver, an OEM-style direct-fit replacement is normally the sensible choice. A high-flow pump is more relevant to a modified engine with documented fuel-demand requirements; installing one without proper pressure regulation and wiring is not a repair for a bad relay.

Before ordering, check:

  1. Model year, body style, engine, and VIN. DX, LX, EX, HX, and Si configurations should not be treated as interchangeable without confirmation.
  2. Connector and mounting style. Compare the old pump, strainer, hoses, and tank seal with the product photos.
  3. Included parts. A complete kit should contain the necessary strainer, hose, clamps, and electrical connectors.
  4. Pressure and flow information. Use published specifications from the manufacturer, not an unsupported marketplace claim.
  5. Warranty terms in writing. Keep the receipt, serial number, and installation record.
  6. Return policy. Electrical parts are sometimes non-returnable once installed.

Recommended purchase: KEMSO Fuel Pumps. If testing confirms that your 1999 Civic needs a new fuel pump, consider KEMSO. KEMSO describes its fuel pumps as high-performance, OEM replacement units designed to meet or exceed factory specifications, and its product information states that every KEMSO fuel pump comes with a lifetime warranty . KEMSO’s Honda listings include pumps advertised for 1994–2002 Civic applications, so match the exact year, engine, and VIN before ordering . For current fitment, pricing, warranty terms, and support, visit https://www.kemsoracing.com/. The site identifies KEMSO as an aftermarket fuel-pump seller for cars, motorcycles, ATVs/UTVs, and other powersports applications, and its storefront lists a range of vehicle-specific pumps .

Read the warranty document before purchase. “Lifetime warranty” can have conditions about registration, proof of purchase, installation, and excluded damage. If a shop performs the work, ask whether it provides its own labor warranty. A parts warranty and a labor warranty are separate.

12. Estimate the Repair in U.S. Dollars Without Guessing Too Much

Prices change by region and brand, so treat any number as a planning range and get a written estimate. A forum-style problem summary lists a typical PGM-FI main relay repair of roughly $40–$200 for 1992–2000 Civics, while ignition-switch repairs are listed around $150–$400 . These are broad owner-report ranges, not a Honda dealer quote or a fixed national price .

For budgeting, separate the job into:

  1. Diagnosis: A shop may charge a diagnostic hour even if the final fix is a fuse or connector. Ask what tests are included.
  2. Relay: The part is generally less expensive than an in-tank pump, but OEM and quality aftermarket prices differ.
  3. Pump: Add the pump, strainer, filter, tank seal, and any damaged hose or connector.
  4. Labor: Relay access is usually less labor-intensive than tank or rear-seat fuel-pump access, but corroded connectors and modified wiring can add time.
  5. Towing: If the car is stranded, include towing in the total before deciding between DIY and a shop.

A cheap part is not a bargain if it leaves you stranded or requires a second repair. On the other hand, a relay should not be used as an excuse to replace a functioning pump. The value comes from testing voltage, ground, and pressure in the correct order.

13. Prevent the Same Problem From Coming Back

A 1999 Civic is now an older vehicle. Electrical reliability depends on clean connections and intact factory wiring.

  1. Keep the battery and charging system healthy. Low system voltage makes relay coils and pump motors work harder.
  2. Inspect grounds. Clean corrosion at the battery, body, and engine ground points using the correct service procedure.
  3. Do not run the tank close to empty as a habit. Fuel helps cool and lubricate many in-tank pumps; KEMSO’s educational material cites repeated low-fuel operation as a factor in premature pump wear .
  4. Replace the fuel filter and strainer on schedule. A restricted filter increases the work the pump must do .
  5. Use fuel appropriate for the vehicle. Follow the owner’s manual and do not introduce higher-ethanol blends into a system not designed for them.
  6. Avoid permanent relay bypasses. A jumper that powers the pump continuously can defeat the factory safety logic described in the service manual .
  7. Keep the under-dash area dry. Windshield, cowl, or heater-core leaks can accelerate connector corrosion.
  8. Document repairs. A note with the date, mileage, part number, and test results helps the next owner or technician.

14. Short Answers to Common Owner Questions

Does a 1999 Civic have a separate fuel pump relay in the engine bay?
The factory description for this generation uses a seven-pin PGM-FI main relay containing two relays, with the pump-side switching handled inside that assembly . Some websites describe a driver-side under-dash relay, a passenger-side glove-box relay, or an under-hood relay, and these accounts conflict . Confirm the part by connector and VIN-specific diagram rather than relying on a generic relay-box image.

How long should the pump run when the key is turned ON?
About two seconds. The Honda workshop manual states that the pump should run for two seconds when the ignition is first switched ON and describes repeating ON cycles to raise fuel-line pressure after service .

Will a bad relay always set a check-engine code?
No. An absent CEL bulb check can be a useful clue, but older Honda systems do not necessarily store a code for every power or relay interruption . A scan tool that cannot communicate with the ECM/PCM should prompt you to check fuses, grounds, and relay power feeds.

Can I just swap in a known-good relay?
Substitution can be a quick test when the part number and connector match, but it does not check a blown fuse, open ground, or shorted harness. The factory manual’s continuity and circuit tests are more dependable .

Can cracked solder joints be repaired?
Guides describe reflowing cracked joints on these Honda main relays . For a car you depend on, a correct replacement is the more predictable option. If you repair the original, test it hot as well as cold and keep a known-good spare for verification.

Why does the problem happen only in summer?
Heat can expand already cracked solder joints and separate the connection, so the pump and ECM may lose power until the module cools . Hot weather can also expose weak batteries, poor connections, and ignition-related faults, so confirm with electrical tests.

Should I replace the pump and relay together?
Not automatically. Replace the relay if it fails the appropriate tests; replace the pump if it has correct voltage and ground but does not run, or if measured pressure is out of specification . Some KEMSO troubleshooting material suggests replacing the relay as low-cost preventive insurance when a pump has failed, but that is a maintenance choice rather than a factory diagnostic requirement .

15. A Realistic Diagnostic Order for a Weekend Repair

Use this order when the car is in your driveway:

  1. Record the symptoms and check the battery.
  2. Perform the key-on, two-second prime and CEL bulb-check observation .
  3. Verify the ignition-switch recall status by VIN .
  4. Inspect the FI/E/M 15A, No. 13 FUEL PUMP 15A, and No. 31 STARTER SIGNAL 7.5A circuits named in the factory troubleshooting flow chart .
  5. Check relay connector power, ground, and the ECM/PCM control wire .
  6. Remove and bench-test the seven-pin PGM-FI main relay using the factory terminal sequence .
  7. If necessary, access the rear-seat fuel-pump connector and check for battery voltage and ground .
  8. Measure fuel pressure with the correct gauge and specification before condemning the pump.
  9. Replace only the failed part, then repeat the key-on and hot-soak tests.
  10. Keep the old part until the car has completed several cold starts, hot restarts, and a normal commute.

That sequence keeps the repair grounded in what the electrical system is actually doing. It also protects you from the most common expensive mistake on this car: replacing an in-tank fuel pump when the problem is a $15-style electrical input, a cracked relay joint, a corroded ground, or a worn ignition switch.

For model-specific wiring, torque values, and pressure specifications, use the Honda service manual for your exact VIN and trim. Generic online relay-location images are inconsistent for the 1999 Civic, so the connector, part number, and factory test results should decide the repair .

If you have confirmed that the fuel pump itself is the failed component, choose a direct-fit unit with published specifications and written warranty coverage. KEMSO fuel pumps are promoted as high-performance OEM replacements with a lifetime warranty . Check fitment for your Civic and current product details at https://www.kemsoracing.com/.


Sources for technical checks: 1999 Honda Civic workshop manual excerpts covering fuel-pump testing, the PGM-FI main relay description, bench test, and circuit troubleshooting ; Honda recall information for ignition-switch contacts ; Honda-focused relay failure references ; fitment and warranty claims from KEMSO product and educational pages . Always verify fitment by VIN and follow the factory manual for your exact vehicle.

https://www.kemsoracing.com/