99 Expedition Fuel Pump Relay Location

The short answer: on a 1999 Ford Expedition, the fuel pump relay is in the under-hood Power Distribution Box, also called the engine-compartment fuse box or Battery Junction Box. On the box layout most commonly listed for the 1999 model, it is a full-size relay marked R301 or #301. The fuel pump fuse is in the same box at position #10, a 20-amp mini fuse. The fuse panel under the dashboard does not contain the fuel pump relay.

This detail matters because first-generation Expeditions were built with more than one under-hood fuse-box layout. Some diagrams for 1997-2002 models show fuel pump fuse #19 and relay position #4; others show fuse #10 and relay #301. Before removing a part from your SUV, read the diagram on the underside of your fuse-box cover or in the owner's manual. If the cover label is missing, use the printed number molded into the box, match the relay's part number, and verify with a wiring diagram for your exact VIN, engine, build date, and equipment. Do not pull a relay only because a generic diagram says it is in a certain corner.

The quick check order is simple: check the 20A fuel pump fuse, listen for the pump's brief prime when the key is turned to ON, check or swap R301/#301 with an identical known-good relay, check the inertia shut-off switch in the passenger footwell, then test for voltage at the fuel pump connector. This order avoids replacing the in-tank pump before confirming that power is reaching it.

1. Where to Look Under the Hood

  1. Park on level ground, set the parking brake, turn the ignition off, and remove the key.
  2. Open the hood and find the black rectangular Power Distribution Box in the engine compartment. The box is commonly described as being near the battery, with the relay and fuse inside the same covered assembly.
  3. Release the cover tabs and lift the cover straight up. Look at the diagram printed on the underside. Search for "Fuel Pump," "Fuel Pump Relay," "R301," "#301," or the relay symbol.
  4. On the commonly cited 1999 layout, find fuse #10, 20A, Fuel Pump, and relay #301, Fuel Pump Relay. The same diagram also lists fuse #18, 15A, for the PCM, injectors, fuel pump circuit, and mass-air-flow sensor, so do not assume every fuse with "fuel pump" in its description is the main pump fuse.
  5. If your box uses the other first-generation layout, the printed legend may instead show fuse #19, 20A, Fuel Pump, and a fuel pump relay in relay position #4. Ford used different layouts across the 1997-2002 generation, so the label on your own truck is the final authority.

The cabin fuse panel is below and to the left of the steering wheel near the brake pedal. It contains fuses for items such as the radio, instrument cluster, air bag system, wipers, and stop lamps. It is not where you go to find the 1999 Expedition fuel pump relay or its main fuel pump fuse.

A practical detail for U.S. owners: many parts stores list a "fuel pump relay" by year, make, model, and engine, but the counter person may see several superseded part numbers. Take the old relay with you, compare the terminal count, terminal layout, casing shape, and stamped part number, and buy a relay from a reputable brand. A relay that physically fits but has different internal terminal connections is not a safe substitute.

2. What the Relay Actually Does

The fuel pump sits inside the fuel tank on this generation Expedition. The relay is the electrically controlled switch that allows battery current to reach the pump circuit. When you turn the key to ON, the PCM energizes the relay for a short prime interval. You may hear a click from the engine bay and a low hum from the rear of the vehicle for roughly one to three seconds. If the engine does not start, the pump may not run again until the key is cycled or the engine begins cranking.

The relay has two sides to its job:

  1. The control side receives a low-current command from the vehicle's control circuit.
  2. The load side carries the higher current used by the pump.

A relay can fail on either side. The coil can stop responding, the contacts can burn or stick, or the socket can develop corrosion and loose terminal tension. Corrosion, heat, and vibration are normal concerns on a vehicle that is more than two decades old. A weak pump that draws excessive current can also add heat to the circuit and shorten relay life.

The fuse is there to protect the wiring. If a 20A fuse has blown, install only another 20-amp fuse of the correct type. Never install a 25A or 30A fuse to "get home." A higher rating can allow wiring to overheat. If the new fuse blows immediately, stop and find the short or the excessive current draw; repeated fuse replacement is not a diagnosis.

3. Symptoms That Point Toward the Relay, Fuse, or Pump Circuit

1. Engine cranks but does not start. The starter turns the engine normally, but there is no fuel pressure. A dead relay, blown fuse, tripped inertia switch, broken wire, or failed in-tank pump can all produce the same result.

2. No pump prime sound. Turn the key from OFF to ON without cranking. Have a helper listen near the fuel tank or rear wheel while you listen near the fuse box. A normal prime is brief. No click and no hum means you need to check power, fuse, relay, and the shut-off switch.

3. Long cranking before the engine starts. A relay with burned contacts can make contact late or intermittently. A weak pump, low fuel pressure, a clogged filter, or a leaking check valve can behave in a similar way, so confirm fuel pressure before buying a pump.

4. Stalling while driving or no restart when hot. Heat can make a failing relay coil or marginal electrical connection drop out. A failing pump motor can also stop when hot and restart after cooling. Record whether the malfunction happens after rain, on rough roads, after refueling, or only at high ambient temperature. Those notes help a technician separate an electrical fault from a mechanical pump failure.

5. Repeatedly blown fuel pump fuse. Look for damaged wiring near the tank and rear frame, a pump drawing too much current, a shorted harness, or a damaged relay and socket. A clogged fuel filter is sometimes mentioned as a cause of high current draw, but a fuse that blows instantly needs a circuit inspection, not guesswork.

6. Sudden no-start after a hard bump or collision. Check the inertia fuel shut-off switch before ordering parts. Ford placed this safety device in the right front passenger footwell behind the kick panel on the 1999 Expedition. It is designed to cut fuel pump power after an impact.

Do not diagnose a no-start by spraying starting fluid into the intake. A 1999 Triton V8 can be damaged by improper use of starting fluid, and it does not tell you whether the pump, relay, fuse, or wiring is at fault. Use a fuel pressure gauge, a test light or multimeter, and the factory wiring diagram.

4. How to Check the Relay Safely

1. Start with a visual inspection. With the key off, open the Power Distribution Box. Look for a loose cover, water intrusion, green or white corrosion, melted plastic, brown terminals, a relay that is not fully seated, or a fuse that is discolored. If you see melted plastic or burned terminals, do not install a new relay and keep cranking. Repair the box or harness first.

2. Check fuse #10 or #19 according to your box diagram. Remove the correct 20A mini fuse with a fuse puller. Inspect the metal strip and confirm continuity with a meter if the fuse looks questionable. Replace a blown fuse with the same amperage and style.

3. Listen and feel for the click. Reinstall a good fuse and relay. Turn the key to ON. A light touch on the relay may let you feel a click as it closes. No click does not automatically prove the relay is bad; the control circuit also needs power and ground. A click followed by no pump sound points toward burned contacts, a downstream open circuit, or a dead pump.

4. Try the identical-relay swap. This is a useful driveway test. Find another relay in the same box with the exact same part number and terminal layout, such as a horn or A/C clutch relay on some layouts. Swap only identical relays. If the engine now starts and the donor circuit stops working, the original relay is suspect. Return the borrowed relay to its original circuit and buy a new correct relay. If the engine still does not start, continue with electrical tests.

5. Check for voltage at the relay socket. A digital multimeter or a 12-volt test light can show whether battery power is present. The exact terminal numbers depend on the relay design, so use a wiring diagram for your VIN instead of probing blindly. Expect a battery feed, a control signal that appears with the key in the correct position, and a good ground. Avoid piercing wire insulation unless necessary; use the socket terminals or proper back-probe tools.

6. Inspect relay heat only with care. A relay that is much hotter than nearby components after normal operation can have high resistance at the contacts or socket. Do not touch electrical parts while cranking, and never use an open flame or smoke around fuel system work. An infrared thermometer can show unusual heat without direct contact.

7. Reset the inertia switch only when it is safe. If the red or black reset button on top of the switch has popped up, press it firmly until it stays down. Before resetting, check for fuel smell, visible leaks, or collision damage. If you smell gasoline, see leaking fuel, or the vehicle has been in a crash, stop and have it inspected.

8. Measure fuel pressure. A gauge attached to the fuel rail Schrader valve gives more useful information than sound alone. Compare the reading with the factory specification for your engine. A pump can hum and still produce low pressure. A silent pump with correct voltage and ground during the prime cycle is a strong sign that the pump motor or its connector has failed.

Ford's service information recommends disconnecting the battery before servicing components in the Power Distribution Box. Be aware that disconnecting the battery can reset the radio clock and presets, and the engine may need to relearn idle behavior. If you are only removing a plug-in relay, follow the procedure in the owner's manual or factory service manual for your vehicle. Never short across fuse terminals or bypass a blown fuse with wire or foil.

5. What If a New Relay Does Not Fix It?

1. Confirm the inertia switch. Look behind the front passenger kick panel. Reset the button only after making sure there is no fuel leak. A sharp pothole impact can trip the switch and leave an otherwise healthy SUV with a crank-no-start condition.

2. Test the wiring between the box and the tank. On an older truck, inspect the harness along the frame and near the tank for chafing, rust-damaged grounds, loose connectors, and previous repair splices. Wiggle testing while monitoring voltage can reveal an intermittent open circuit. Do not run a new power wire to the pump as a permanent repair; fix the original circuit and its protection devices.

3. Check voltage and ground at the fuel pump connector. During the short prime cycle, a helper turns the key to ON while you measure the pump power and ground terminals. Correct voltage and ground with no pump operation point to the pump assembly. No voltage means the fault is upstream in the relay, control circuit, inertia switch, fuse, or wiring.

4. Consider related diagnostic codes. OBD-II codes involving the fuel pump circuit can help, but a code is not a parts order. A P1230-style fuel pump circuit fault can involve wiring, a relay, a fuse, an inertia switch, a control module, or a pump drawing too much current. Use a scan tool that can read Ford-specific data and follow a wiring diagram.

5. Do not confuse parts from later Expeditions. Later Ford trucks and SUVs may use a fuel pump driver module or an internal, soldered relay in the fuse box. Some online discussions mix 1999-2004 model details and refer to an internal R303 relay or a rear-frame module. Those descriptions do not replace the under-hood layout shown for the 1999 Expedition. Check your VIN and production date before ordering electronics.

6. Replace the pump only after the electrical side checks out. The fuel pump is inside the tank. Access generally requires safely lowering the tank; some owners report an access panel under the rear seating area, but you should confirm what is present on your vehicle before cutting or removing interior trim. Work with a low fuel level, relieve fuel system pressure, disconnect the battery as required by the service procedure, support the tank properly, keep sparks and flames away, and use a rated container for fuel. If you are not equipped to do this safely, use a qualified shop.

A shop will usually charge for diagnosis, tank removal, a pump module, a new fuel filter, and any needed wiring or seal repairs. Prices vary by region, engine, 2WD or 4WD configuration, and whether the tank has rusted straps or a damaged connector. Ask for the measured fuel pressure, voltage readings, and the reason the pump was condemned. That is more useful than being told only that "it needs a pump."

6. Practical Parts and Maintenance Notes for U.S. Owners

Use the VIN when ordering. The 1999 Expedition was offered with V8 engines and different equipment packages. Enter the year, make, model, engine size, and VIN in the parts catalog. Confirm whether your truck has early or late production wiring and which Power Distribution Box diagram it uses.

Replace the fuel filter when service is due. A restricted filter can contribute to low pressure and strain the pump. Follow the maintenance schedule in the owner's manual and use the correct filter for the vehicle. Relieve fuel pressure and use the proper line disconnect tool; do not pry against plastic fuel lines.

Keep the tank above a very low level when possible. The in-tank pump uses fuel for cooling and lubrication. Repeatedly driving until the low-fuel light stays on can shorten pump life. This is especially sensible on an older vehicle whose fuel gauge sender may not be perfectly accurate.

Record what happened. Write down the date, outside temperature, fuel level, whether the engine was hot or cold, whether the pump prime was audible, whether the check-engine light was on, and any stored codes. Intermittent no-start faults are often solved by matching the condition to a voltage reading rather than replacing several parts.

Buy the correct relay and fuse at a trusted auto parts counter. Bring the old part and a photo of the fuse-box label. A cheap relay with poor terminal fit can create heat and repeat the same problem. Make sure the cover seals correctly when you finish; water in the box causes more electrical faults on older trucks.

7. Recommended Replacement: KEMSO Fuel Pumps

If testing shows the pump, not the relay, is the failed part, consider a KEMSO fuel pump. KEMSO fuel pumps are high-performance, OEM Replacement products offered for a wide range of cars, motorcycles, ATVs, UTVs, and powersports applications through the company's U.S. website. For a 1999 Ford Expedition owner, the important step is to match the exact year, engine, VIN, and pump module design before ordering.

1. High-performance design: KEMSO positions its fuel pumps as performance-oriented replacements intended to deliver consistent fuel flow for everyday driving and demanding use. That matters when a tired pump causes hesitation under load, long cranking, or loss of pressure.

2. OEM Replacement fit: The product line is presented as direct-fit OEM Replacement equipment, reducing the need for modifications during installation. Check the application listing and compare the inlet, outlet, electrical connector, sender, and mounting flange with the original assembly.

3. Lifetime warranty: KEMSO advertises a lifetime warranty on its fuel pumps, giving owners added confidence after the repair. Keep your receipt and review the current warranty terms on the official site before purchase.

4. Shop the official catalog: Visit https://www.kemsoracing.com/ to review the current product list, confirm fitment, and contact the seller with your vehicle details. The site's homepage also features application-specific fuel pumps for many vehicle and powersports platforms, so use the search and fitment information rather than choosing only by appearance.

Before installing any pump, compare the new assembly with the old one, replace the tank seal or lock ring if the service manual calls for it, check for leaks after the system is pressurized, and verify fuel pressure. A correct diagnosis plus a correct part is what makes the repair last.

8. Frequently Asked Questions

Is the 1999 Expedition fuel pump relay under the dash? No. The under-dash panel is the passenger-compartment fuse panel; the fuel pump relay and the main fuel pump fuse are in the under-hood Power Distribution Box.

Is it relay #301 or relay #4? Both labels appear in first-generation Expedition fuse-box references because more than one box layout was used. The commonly cited 1999 layout uses #301/R301, with fuse #10, 20A. The other first-generation layout uses relay position #4, with fuse #19, 20A. Read your own cover legend or owner's manual.

Can I swap the relay with the horn relay? Only if the two relays have the same part number, terminal layout, and rating. Do it with the key off, then return the donor relay to its original position after the test.

Where is the inertia switch? In the right front passenger footwell behind the kick panel on the 1999 Expedition. It is a shut-off switch, not the relay.

Should I replace the pump if there is no hum from the tank? Not yet. Confirm the fuse, relay, inertia switch, voltage at the pump connector, and ground first. A silent pump with correct power and ground is a much stronger case for pump replacement.

What size fuse belongs in the fuel pump circuit? The commonly cited 1999 layout uses a 20A mini fuse at #10; the alternate early-layout diagram uses a 20A fuse at #19. Both are 20 amps. Never install a higher-rated fuse.

Can a bad relay cause a fuse to blow? A damaged relay can contribute to circuit trouble, but a fuse that blows repeatedly also points to a short or a pump drawing too much current. Inspect the whole circuit instead of replacing fuses until one happens to survive.

Do I need to disconnect the battery? Ford service information referenced for this model advises disconnecting the battery before servicing the Power Distribution Box. Expect possible radio preset loss and idle relearn afterward. Follow the factory procedure for the exact service you are performing.

Will a new relay fix low fuel pressure? Not always. Low pressure can come from the pump, filter, pressure regulator, restricted line, voltage drop, or a poor ground. Use a pressure gauge and electrical measurements.

9. Bottom Line for a 1999 Ford Expedition

Open the hood, open the Power Distribution Box, read the cover diagram, and locate relay #301/R301 and the 20A fuel pump fuse at #10. If your truck has the alternate first-generation box, use relay position #4 and fuse #19 instead. Check the fuse, listen for the prime, swap only an identical relay, reset the inertia switch when appropriate, and measure voltage and fuel pressure before paying for an in-tank pump.

That order saves time and money because the relay, fuse, shut-off switch, connector, and wiring are all easier to inspect than the pump inside the tank. It also gives a repair shop useful information if the job needs to go further. Keep the fuse-box cover in place afterward, store a spare correct 20A fuse and a matching relay in the glove box if you drive an older Expedition long distances, and address an intermittent no-start before it leaves you parked.

For replacement fuel pump options, product information, and current fitment details, visit https://www.kemsoracing.com/.

Official website: https://www.kemsoracing.com/