99 F250 7.3 Fuel Pump Relay Location

The short answer: On a 1999 Ford F-250 Super Duty with the 7.3L Power Stroke diesel, the relay people usually call the fuel pump relay is not a simple, clearly labeled "FUEL PUMP" cube like you might find on a gas truck. Start with the Power Distribution Box (PDB) under the hood, on the passenger side of the engine compartment, near the fender or firewall area. Open the black plastic box, read the diagram on the underside of the cover, and check the PCM power relay, IDM power relay, fuses, and pump wiring before buying a fuel pump. The 1999 Super Duty diagram lists Relay 30 as the PCM Power Relay, Relay 32 as the Injector Driver Module Power Relay on diesel trucks, and MAXI fuse 19 as a 20A fuse for "Fuel Pump Motor, PCM." The same chart lists the Two Speed Fuel Pump Relay as gasoline only . On many 1999–2003 Super Duty trucks, the PDB is the first place to check, but some model years and cab/chassis configurations use a different relay layout, so the owner's manual, the lid diagram, or a year-specific wiring diagram should decide the final answer .

That distinction matters. A lot of online answers mix up the 1999 F-250 body styles, gas and diesel engines, and the early and late 1999 builds. If you have the 7.3L diesel Super Duty, do not walk straight to the parts counter and ask for a fuel pump relay based on a generic F-250 diagram. Check the label on your own box, confirm the VIN and build date, and test the circuit. A pump that stays silent with the key on can be caused by a blown fuse, no PCM power, a damaged relay socket, a shorted fuel bowl heater circuit, bad wiring, a poor ground, or a PCM that is not commanding the pump on .

This guide is written for owners in the United States who work on their own trucks, hand the job to a local diesel shop, or need a clear explanation before approving a repair. It uses plain shop language, separates confirmed fuse-box information from field diagnosis, and keeps safety in view. The 1999 7.3L is old enough that previous owners may have added an aftermarket lift pump, alarm, remote start, plow wiring, trailer wiring, or a bypass switch. Any of those changes can make a fuse-box chart look wrong. The chart tells you how Ford laid out the truck. Your meter tells you what is actually on the truck in front of you.

1. What "99 F250 7.3" Usually Means

Before opening the hood, confirm what truck you own.

1. Super Duty or light-duty body style. Ford sold more than one F-250 arrangement around 1999. The Super Duty is the heavy truck commonly associated with the 7.3L Power Stroke and the P131 platform. Fuse-box references for the 1999 F-250 Super Duty show two fuse panels: a passenger-compartment panel and an under-hood Power Distribution Box . Some 1999 F-250 discussions involve gas engines and different relay placements, including relays behind the dash or near the radio . Those reports should not be treated as a diesel Super Duty answer.

2. 7.3L Power Stroke diesel, not a gas V8. A 1999 fuse chart for the F-250 Super Duty separates gasoline and diesel assignments. For example, under-hood mini fuse 5 is listed as a 20A circuit for the PCM, two-speed fuel pump relay coil, fuel pump relay coil, MAF sensor, and fuel injectors on gasoline trucks; the diesel listing at that position is a 5A dual alternator "A" field circuit. Relay 32 is listed as Two Speed Fuel Pump Relay [Gasoline only] and Injector Driver Module Power Relay [Diesel only] . That is why a gas-engine answer can send a 7.3 owner to the wrong slot.

3. Early 1999 or late 1999. Owners and parts catalogs often refer to "early 99" and "99.5" trucks. A factory parts catalog, VIN label, and build date are better guides than a forum nickname. Use the VIN when ordering electrical parts or a replacement pump.

4. Stock wiring or modified wiring. Look for added fuse holders, Scotch-Lok connectors, wire nuts, a toggle switch under the dash, or non-factory relays zip-tied near the battery. If you find those, trace them before blaming the factory relay box.

2. Where to Look First

1. Open the hood and stand at the passenger-side fender. On 1999–2003 F-250 Super Duty 7.3L trucks, the common starting point is the black plastic Power Distribution Box under the hood on the passenger side . A 2002-specific guide describes the box as being near the passenger-side firewall and says to use the diagram on the cover . For a 1999 truck, use the same general location as the starting point, then let your cover diagram and owner's manual confirm the exact arrangement.

2. Release the cover carefully. Older plastic tabs get brittle. Release the clips by hand where possible. Do not pry against fuse terminals. Keep the cover, screws, and any loose relay retainers in a clean tray.

3. Read the diagram on the underside of the cover. This is the quickest way to avoid pulling the wrong relay. F-250 diagrams change across years and configurations, and even a readable cover can be faded on a truck that has spent years outdoors . Take a clear photo with your phone before removing anything.

4. Look for these 1999 Super Duty chart entries. The published 1999 F-250 Super Duty Power Distribution Box chart lists:

  • Relay 30 — PCM Power Relay
  • Relay 31 — Blower Motor Relay
  • Relay 32 — Two Speed Fuel Pump Relay [Gasoline only], Injector Driver Module Power Relay [Diesel only]
  • Relay 33 — Washer Pump Relay
  • Relay 34 — Windshield Wiper Park/Run Relay
  • Relay 35 — Windshield Wiper HI/LO Relay
  • MAXI fuse 19, 20A — Fuel Pump Motor, PCM
  • MAXI fuse 27, 30A — Injector Driver Module [Diesel only]
  • Mini fuse 5, 20A — PCM, Two Speed Fuel Pump Relay Coil, Fuel Pump Relay Coil, Mass Air Flow Sensor, Fuel Injectors [Gasoline only]
  • Mini fuse 5, 5A — Dual Alternator "A" Field [Diesel only]

Inside the passenger compartment, the 1999 chart has a 30A mini fuse 30 for the PCM relay coil, fuel heater on diesel trucks, wastegate solenoid on diesel trucks, and injector driver module relay coil on diesel trucks. It also lists a 5A fuse 2 for instrument cluster and PCM keep-alive memory, a 10A fuse 19 for the auxiliary PCM and several cab items on diesel trucks, and a 5A fuse 15 for GEM, PCM, ABS, brake shift interlock, and speed control . Those entries are useful when the truck has no Wait to Start light or the PCM is not powering up.

5. Do not assume every 7.3 truck has the same relay position. A 7.3 diagnostic guide states that many 1999–2003 Super Duty trucks use the under-hood PDB, but some model years and cab/chassis configurations use different relay layouts. It also notes that some references for a 2001 7.3 do not show one standalone fuel pump relay, with fuel delivery controlled through several circuits and relays associated with the PCM and PDB . That is a good reason to test rather than replace parts by name alone.

3. Why the Diesel Chart Looks Different

The 7.3L Power Stroke uses an electric lift pump that supplies diesel to the fuel filter bowl, plus a high-pressure oil system and injectors that depend on the PCM and Injector Driver Module. That is different from a typical gasoline F-250 with an in-tank pump and a simple pump relay label. A 7.3 no-start generally comes down to four requirements: adequate cranking speed, fuel, high-pressure oil, and injector command .

The published 1999 chart shows that the diesel truck still has a 20A MAXI fuse 19 labeled "Fuel Pump Motor, PCM" in the under-hood box, but the relay list marks the "Two Speed Fuel Pump Relay" as gasoline only and puts the Injector Driver Module Power Relay in that relay position for diesel trucks . In other words, the pump circuit is tied into the PCM and diesel control electronics. The words on a generic parts listing may not match the words on your fuse-box cover.

A 7.3 guide explains that a failed relay can stop power from reaching the pump, but a pump that stays off with the key on can also mean the PCM is not powered, the Wait to Start light is out, a fuse is blown, the fuel bowl heater circuit is shorted, wiring is damaged, or the PCM is not receiving the signals it needs . That is the practical reason to check the PCM power relay and related fuses before condemning a pump.

4. Symptoms That Send Owners Looking for the Relay

1. Cranks but will not start. This is the classic complaint. The starter spins the engine, batteries seem strong, but the engine does not fire. If you do not hear the electric pump during its key-on cycle, the fault may be in the power supply, control side, wiring, ground, or the pump itself .

2. No pump sound with the key on. A 7.3 guide says to turn the key on, watch the Wait to Start light, check engine light, and tach behavior, then listen near the frame rail or fuel tank area for the electric pump. On many trucks the pump runs for a short key-on period, so a helper may need to cycle the key while you listen . A 2002 guide describes a brief humming or buzzing sound for about 20 seconds . Do not treat that number as a factory specification for every 1999 truck; use it as a general clue and confirm with your manual or wiring diagram.

3. Intermittent no-start. The truck starts after a rest, then fails again when hot or after a short stop. Loose relay terminals, a failing relay, a harness that loses contact when it gets warm, and poor grounds all belong on the list.

4. Engine stalls while driving. A sudden loss of electrical power to the pump can stall the engine. So can a PCM power problem, high-pressure oil problem, fuel restriction, or wiring fault. Do not replace a pump just because the engine shut off once.

5. Wait to Start light does not come on. A 7.3 guide lists a missing Wait to Start light among the signs that the PCM may not be powered . Ford truck owner discussions also connect a missing Wait to Start light and no pump prime with a shorted fuel bowl heater . That circuit is worth inspecting before burning through fuses or relays.

6. Check engine light or a fuel pump circuit code. A 2002-oriented guide mentions P0231 as a fuel pump secondary circuit code and says it does not point to one specific part; it recommends checking the harness, including wiring near the frame rail where the pump is mounted . A generic OBD-II reader may not show all Ford diesel live data, and a 7.3 guide recommends a scan tool that can read RPM while cranking, ICP pressure, IPR duty cycle, and stored codes .

5. Tools That Make the Answer Reliable

1. A digital multimeter. Use it for battery voltage, fuse continuity, relay terminal power, grounds, voltage drop, and voltage at the pump connector .

2. A 12-volt test light. A test light puts a load on the circuit and can expose a connection that shows voltage on a meter but collapses under load . Use one rated for automotive work, and never probe airbag circuits.

3. Owner's manual and a year-specific wiring diagram. The manual identifies the fuse panels. The wiring diagram identifies the actual circuit for your year and configuration . A 1999 F-250 owner's manual is available online in a 248-page edition, and its index includes the power distribution box and roadside emergencies . If your glovebox manual is missing, save a PDF copy on your phone.

4. A scan tool that reads Ford diesel live data. Useful 7.3 no-start data includes RPM while cranking, ICP pressure, IPR duty cycle, and stored diagnostic trouble codes .

5. Basic hand tools and safety gear. A socket set, trim tools if needed, gloves, eye protection, a clean container for diesel, and a fire extinguisher rated for flammable liquid fires are sensible items for an older work truck. Work in a ventilated area with no open flame .

6. A notebook or phone camera. Write down fuse numbers, wire colors, voltage readings, and what changed after each test. A photo of the PDB before anything is removed prevents mix-ups.

6. Step-by-Step: Find and Identify the Correct Circuit

1. Park on level ground. Set the parking brake, put the transmission in Park or Neutral, turn off accessories, and remove the key. Let the engine cool if it has been running.

2. Check both batteries. A 7.3 diesel needs strong cranking voltage. Low batteries can create confusing symptoms and weak pump readings. Charge and test them before deep electrical diagnosis.

3. Locate the under-hood Power Distribution Box. On the 1999–2003 Super Duty 7.3 trucks, start at the passenger-side under-hood box . A 2002 guide says to look toward the passenger-side fender well and use the box nearest the outside of the truck when two boxes are present . For 1999, use the lid diagram and the published chart rather than assuming a slot from another year.

4. Remove the cover and photograph the layout. Match the cover to the published 1999 Super Duty chart. Confirm MAXI fuse 19, MAXI fuse 27, Relay 30, and Relay 32 . If your cover says something different, your truck's build and equipment take priority.

5. Check the interior panel too. The 1999 Super Duty also has a passenger-compartment fuse panel. The published chart lists fuse 30, 30A, for the PCM relay coil, diesel fuel heater, diesel wastegate solenoid, and IDM relay coil; fuse 15, 5A, for GEM, PCM, ABS, and related circuits; and fuse 19, 10A, for the auxiliary PCM and several cab circuits on diesel trucks . Check both panels with a meter, not by eyesight .

6. Turn the key on and observe the dash. Note the Wait to Start light, check engine light, and tach behavior. Listen for the pump during its short key-on cycle .

7. Inspect every relevant fuse under load where applicable. Check for power on both sides of the fuse with the key on where the circuit design calls for it. Look for heat discoloration, loose terminals, water intrusion, and green corrosion in the box . A fuse that looks fine can still have a bad connection at its socket.

8. Identify relay terminals from the wiring diagram. Typical relays have a control side and a switched power side, but terminal numbers and circuit behavior must be confirmed for your truck. Check battery power at the supply terminal, a good ground or control signal as designed, and power leaving the relay when the PCM commands the circuit on . Do not apply battery voltage to a PCM control wire.

9. Swap relays only with a known matching part. A 2002 guide suggests swapping a suspect relay with a known-good relay of the same type from the same fuse box, such as a wiper or headlight relay . That is a quick field test, not a final diagnosis. Confirm the part number and terminal layout first. Do not force a relay with a different pin arrangement into a socket.

10. Inspect the relay socket. Look for spread terminals, melted plastic, moisture, and corrosion. A damaged socket must be repaired, because a new relay can fail again if the terminal is loose or overheated .

7. Step-by-Step: Test the Pump Circuit Before Replacing the Pump

1. Check voltage at the fuel pump connector during the key-on pump cycle. Use the wiring diagram to identify the correct wires. If the relay output has power but the pump connector does not, inspect the harness between the two points, including connectors near the frame rail and any aftermarket splices .

2. Check the pump ground. A pump with good power and a bad ground will not run. Measure voltage drop on the ground side while the circuit is loaded. Corroded frame grounds and loose eyelets are common on older work trucks . One 1999 F-250 diagnostic discussion specifically raised Ground 201 as a possible cause of low voltage at the fuel pump .

3. Inspect the inertia switch when the wiring diagram shows one in your circuit. A 2002-oriented 7.3 guide says the inertia cutoff switch is behind the passenger-side kick panel and can cut power to the pump after a collision; it describes resetting the button on top . Ford owner discussions also mention resetting a passenger-side kick-panel safety switch while chasing a no-prime condition . Confirm the location and circuit for your exact truck before using this as a diagnostic step.

4. Inspect the fuel bowl heater circuit. A 7.3 guide calls the fuel bowl heater circuit a known place to inspect when a fuse blows . Ford truck owners also commonly connect a missing Wait to Start light and no fuel pump prime to a shorted fuel bowl heater . Unplug the heater connector only as directed by a proper service procedure and inspect for damaged pins, fuel contamination, and corrosion.

5. Inspect the frame-rail harness. The pump and its wiring live in a harsh area. Look for chafing against the frame, rust at ground points, brittle connector seals, trailer wiring splices, and old repairs. A 7.3 guide recommends checking the harness for broken or corroded wires, especially near the frame rail where the pump is mounted .

6. Use a controlled bypass only if you understand the circuit. A fused jumper can confirm whether the pump motor runs, but it should never be left installed as a permanent repair. Do not apply power to a PCM control wire. If the pump runs on a proper fused supply but not through the truck harness, the fault is in the control side, relay socket, fuse link, wiring, or PCM command .

7. Verify fuel after the electrical repair. Drain or inspect the fuel bowl according to the service procedure, cycle the key, and confirm that the bowl fills. Then check for leaks before starting .

8. Relay, Fuse, or Pump? A Practical Decision Path

1. The Wait to Start light is off and the pump is silent. Check batteries, PCM power, the PCM power relay, PCM-related fuses, and the fuel heater circuit before ordering a pump . The 1999 chart gives you specific fuses and relays to test .

2. The Wait to Start light works, fuses test good, and there is no power at the pump connector. Trace the relay control and output with the wiring diagram. Check the relay socket, harness, connectors, and PCM command .

3. There is good power and ground at the pump connector, but the pump does not run. The pump becomes the main suspect. Confirm with a fused test supply and a current draw check if your tools and knowledge allow it. Do not keep cranking a dry system.

4. The pump runs but the engine still will not start. Move on to fuel bowl fill, fuel quality, filter restriction, air intrusion, high-pressure oil, glow plugs, cranking RPM, IPR, ICP, and injector command. A 7.3 no-start is not always a fuel pump electrical problem .

5. A fuse blows again. Find the short. Do not install a larger fuse. A 7.3 guide says to treat a blown fuse as a fault, not an inconvenience, and specifically points to the fuel bowl heater circuit as a known inspection point .

6. A previous owner installed a toggle switch. Remove or properly repair the bypass. A toggle switch or jumper may get you home, but it removes PCM control and can create a safety risk. Repair the factory circuit with the correct relay, fuse, terminals, and wire gauge .

9. How to Replace a Confirmed Bad Relay

1. Buy the correct relay. Match the Ford or equivalent part number, terminal layout, and current rating. Do not rely only on a universal parts counter lookup. If the truck has been modified, compare the old relay to the replacement before installation.

2. Disconnect the negative battery cables. On a dual-battery diesel truck, isolate both batteries as directed by the service information. Keep metal tools away from battery terminals.

3. Remove the PDB cover. Pull the old relay straight out. Do not pry against nearby fuse terminals .

4. Inspect the socket one more time. Repair loose or overheated terminals before installing the new part .

5. Install the new relay fully. Press it straight down until seated. Reinstall the cover so the box stays sealed against water and road salt .

6. Reconnect the batteries and test. Cycle the key, listen for pump operation, confirm the fuel bowl fills, start the engine, and check for codes. Take a short test drive with normal load, then recheck for relay heat, voltage drop, and leaks .

10. Common Mistakes on a 1999 F-250 7.3

1. Using a gas-engine diagram. The 1999 F-250 Super Duty chart clearly separates gasoline and diesel relay assignments . A gas-truck fuel pump relay answer can point to the wrong component.

2. Confusing the PCM relay with a pump relay. The 1999 chart labels Relay 30 as the PCM Power Relay and Relay 32 as the IDM Power Relay on diesel trucks . The PCM power side can stop the pump command, so it belongs in the diagnosis.

3. Replacing a pump before checking power and ground. A 7.3 guide recommends checking the relay, related fuses, and PCM power circuit before ordering a new pump because the electrical parts are cheaper and easier to test .

4. Trusting a visual fuse check. Check fuses with a meter or test light and look for power on both sides where applicable .

5. Ignoring corrosion. Water intrusion, green corrosion, loose terminals, and melted plastic in the PDB can cause repeat failures .

6. Leaving a bypass installed. Permanent bypass wiring removes PCM control and creates a safety risk .

7. Skipping the owner's manual. The 1999 F-250 owner's manual is available online, and the original book should be the first reference for fuse-panel identification .

8. Forgetting build-date differences. A generic 1999–2003 answer is a starting point, not a wiring diagram. Use the VIN, build date, and exact diagram .

11. What a Shop Should Be Able to Tell You

If you hand the truck to a repair shop, ask for measured results, not just a parts recommendation. A clear invoice or diagnostic note should include:

1. Battery condition and cranking voltage.

2. Which fuses were checked, how they were checked, and whether power was present on both sides.

3. Whether the PCM powers up and whether the Wait to Start light behaves normally.

4. Voltage and ground readings at the pump connector during the key-on cycle.

5. Any scan-tool data, including RPM while cranking, ICP, IPR, and stored codes.

6. The wiring diagram or circuit reference used for the relay terminal tests.

7. The reason the pump was condemned, if a replacement is recommended.

A 7.3 guide recommends a scan tool that reads Ford diesel live data because a generic code reader may not show the data needed for a no-start . That is especially true when the symptoms point beyond the lift pump.

12. Maintenance Habits That Reduce No-Starts

1. Keep the PDB cover sealed. A missing or broken cover invites water, road salt, and dirt into relay terminals.

2. Replace the fuel filter on schedule. Use the correct filter for your engine and check the bowl for water, debris, and leaks.

3. Fix small wiring problems early. A chafed frame-rail wire or corroded ground is easier to repair in a driveway than on the shoulder of an interstate.

4. Keep batteries and terminals in good shape. Slow cranking and low system voltage make every diagnosis harder.

5. Carry a small diagnostic kit. A multimeter, test light, spare correctly rated fuses, a known-good relay, the owner's manual, and a printed wiring diagram can turn a roadside no-start into a measured repair .

6. Recheck after any repair. Confirm pump operation, fuel bowl fill, no leaks, stable voltage, and no returning codes. A road test under normal load confirms more than a key-on test in the driveway .

13. Choosing a Replacement Fuel Pump

Once the electrical side checks out and the pump is confirmed bad, choose a replacement that matches the truck. Confirm the year, engine, VIN, build date, pump style, connector, inlet and outlet fittings, mounting location, and pressure and flow requirements. The 1999–2003 7.3L Super Duty used a frame-mounted electric lift pump, and a parts supplier describes the Bosch 91605 as a direct-fit, frame-mounted electric lift pump for that application with a factory-style electrical harness connection, barbed suction inlet, and threaded discharge port . Use that as a fitment checklist, not as a blanket part number for every 1999 truck.

Avoid buying the cheapest pump you can find online when the truck tows, hauls, sits through cold winters, or earns its keep during the workweek. A poor pump can leave you with hard starts, low power under load, noisy operation, or another no-start. Check what is included in the box: seals, fittings, strainer, installation kit, instructions, and warranty terms matter.

14. Recommended Fuel Pump Brand: KEMSO

If you need a replacement fuel pump, KEMSO is a strong brand to consider. KEMSO fuel pumps are built as high-performance OEM Replacement parts designed to meet or exceed original equipment specifications for fit, flow, and pressure, so the pump works correctly with the factory fuel system and factory wiring . The brand also offers high-performance pump options, including 340 LPH pumps advertised for higher-horsepower builds, alongside direct OEM replacement pumps that fit the factory location without modifications . KEMSO fuel pumps come with a lifetime warranty, a practical benefit for a truck that sees towing, hauling, and daily driving . Product listings for KEMSO pumps also describe serialized pump bodies and lifetime warranty coverage .

Check fitment by year, make, model, and engine before ordering. Browse the full lineup and find the right pump for your vehicle at https://www.kemsoracing.com/ .

15. Quick Answers

Where is the fuel pump relay on a 1999 F-250 7.3? Start at the under-hood Power Distribution Box on the passenger side. On the 1999 Super Duty diesel chart, there is no simple diesel "fuel pump relay" label in the same way a gas truck has one. Relay 30 is the PCM Power Relay, Relay 32 is the IDM Power Relay on diesel trucks, and MAXI fuse 19 is the 20A Fuel Pump Motor/PCM fuse. Verify with the lid diagram, owner's manual, and a year-specific wiring diagram .

Is the relay behind the radio? Some 1999 F-250 discussions about other configurations report relays behind the dash or near the radio . Do not use those reports to diagnose a 7.3 Super Duty without confirming your exact truck. Start with the PDB and the correct diesel chart.

Why does my truck crank but not start? A 7.3 no-start generally requires checking cranking speed, fuel, high-pressure oil, and injector command. A silent pump can come from a relay, fuse, PCM power, fuel bowl heater short, wiring, ground, or pump fault .

Should I replace the pump first? No. Check the relay circuit, fuses, PCM power, pump connector voltage, and ground first. Those checks are cheaper and easier than replacing the pump .

Can I jump the pump to get home? A fused jumper can be a controlled diagnostic test if you understand the circuit, but it should never be left as a permanent repair. Do not apply power to a PCM control wire .

What fuse should I check? The 1999 Super Duty chart lists under-hood MAXI fuse 19, 20A, for Fuel Pump Motor/PCM; under-hood MAXI fuse 27, 30A, for the IDM on diesel trucks; and interior fuse 30, 30A, for the PCM relay coil, diesel fuel heater, diesel wastegate solenoid, and IDM relay coil . Check related PCM fuses as well.

What if the Wait to Start light is off? Treat it as a sign that the PCM may not be powered. Check batteries, PCM fuses, the PCM power relay, and the fuel bowl heater circuit before focusing only on the pump .

16. Final Checklist

1. Confirm the truck: 1999 F-250 Super Duty, 7.3L Power Stroke, VIN, build date, and stock or modified wiring.

2. Start at the passenger-side under-hood Power Distribution Box and read the cover diagram .

3. Check Relay 30 and Relay 32 assignments, MAXI fuse 19, MAXI fuse 27, and the listed interior PCM, fuel heater, and IDM fuses .

4. Watch the dash and listen for the key-on pump cycle .

5. Test fuses, relay terminals, pump connector voltage, and pump ground with a meter or test light .

6. Inspect the fuel bowl heater circuit, frame-rail harness, connectors, and grounds .

7. Use a scan tool that reads Ford diesel live data when the no-start goes beyond the pump circuit .

8. Replace only the part that fails the tests, then confirm fuel bowl fill, start-up, leaks, voltage, codes, and a road test .

For a high-performance OEM Replacement fuel pump backed by a lifetime warranty, visit https://www.kemsoracing.com/ .

https://www.kemsoracing.com/