99 F250 Fuel Pump Relay Location: Quick Answer and Full Guide
On most 1999 Ford F-250 Super Duty trucks, the fuel pump relay circuit is in the under-hood Power Distribution Box, the main fuse and relay box on the driver side of the engine bay near the firewall. That is the first place to look. For the 1999 Super Duty fuse chart, relay position R32 is listed as the Two Speed Fuel Pump Relay on gasoline trucks and the Injector Driver Module Power Relay on diesel trucks. The same box also contains a 20A MAXI fuse in position 19 for the Fuel Pump Motor and PCM, and a 20A MINI fuse in position 5 that covers the PCM, fuel pump relay coil, mass air flow sensor, and fuel injectors on gasoline engines .
There is an important warning before you buy parts: 1999 was a split year for the F-250 name. Ford sold the older light-duty F-250 and the new Super Duty F-250 in the same period. Some owner reports describe a fuel pump relay behind the center dash near the radio, reached through the ashtray area, while other 1999 F-250 Super Duty owners found theirs under the hood at the driver-side firewall . Fuse charts, relay labels, and engine equipment can vary, so confirm your exact truck by VIN, engine, build date, the diagram on the Power Distribution Box cover, the owner's manual, or a Ford wiring diagram . If your truck cranks but will not start and the pump does not run with the key on, check the relay, fuses, PCM power circuit, inertia fuel shutoff switch, wiring, and pump connector before ordering a new fuel pump .
1. Start With the Under-Hood Power Distribution Box
The quickest check takes only a few minutes.
1. Park the truck safely. Use level ground, set the parking brake, put the transmission in Park or Neutral, switch off the ignition, and remove the key.
2. Open the hood and find the black fuse and relay box. On a 1999 F-250 Super Duty, look on the driver side of the engine compartment, near the firewall. One owner described it as being "under the hood, drivers side by the firewall, right in the corner," and general F-250 guides place the under-hood power distribution center on the driver side near the firewall or radiator support .
3. Release the cover and read the diagram. Ford usually printed or molded the fuse and relay layout on the underside or top of the cover. Look for wording such as FUEL PUMP, Two Speed Fuel Pump, FP, or PUMP. The cover diagram is more reliable than a generic online picture because it belongs to your truck .
4. Cross-check the 1999 Super Duty chart. Published 1999 F-250 Super Duty fuse diagrams list relay R32 in the Power Distribution Box as the Two Speed Fuel Pump Relay [Gasoline only] or the Injector Driver Module Power Relay [Diesel only] . Do not assume the same label applies to every 1999 F-250, because the diesel and gasoline circuits are not the same .
5. Check the related fuses in that box. The 1999 Super Duty chart lists:
- Fuse 5, 20A, gasoline: PCM, Two Speed Fuel Pump Relay Coil, Fuel Pump Relay Coil, Mass Air Flow Sensor, and Fuel Injectors .
- Fuse 19, 20A MAXI: Fuel Pump Motor and PCM .
- Fuse 20, 15A: Starter Motor Relay Coil and PCM on gasoline engines .
- Fuse 30, 30A: PCM Relay Coil; Ignition Coil on gasoline engines; Fuel Heater, Wastegate Solenoid, and Injector Driver Module Relay Coil on diesel engines .
- Relay 30: PCM Power Relay .
6. Look at the interior fuse panel too. The 1999 F-250 passenger compartment fuse panel is located below and to the left of the steering wheel by the brake pedal . Published 1999 Super Duty diagrams list interior relays for the interior lamps, horn, power windows, and accessory delay; they do not list a standard fuel pump relay in that panel . That panel still matters because it carries PCM keep-alive memory, GEM, ABS, instrument cluster, starter relay coil, and other circuits that can affect a no-start diagnosis .
2. Why Some 1999 F-250 Owners Find the Relay Near the Radio
This is the part that causes confusion in forums and parts stores.
A 1999 F-250 5.4L owner reported that a failed fuel pump relay was hidden in the dash below and to the left of the radio, accessed by removing the ashtray. That same discussion included another owner with a 1999 F-250 Super Duty who said the relay was under the hood on the driver side by the firewall . A separate owner thread about a 1999 F-250 no-start says the owner had heard the relay was behind the radio and was trying to confirm the location after checking the inertia switch and voltage at the pump connector .
There are several practical reasons for the mixed answers:
1. The 1999 model year covered more than one truck family. The new Super Duty and the older light-duty F-250 were both associated with the 1999 model year. A search result for "1999 Ford F250 Super Duty, light duty F-250 fuse box diagram" shows that fuse information was published for both versions . Always identify the truck before using a relay chart.
2. Gasoline and diesel trucks use different fuel system controls. The 1999 Super Duty fuse chart gives relay R32 a different description for gasoline and diesel engines . A 7.3L Power Stroke guide also warns that relay layout can vary by model year and cab or chassis configuration, and recommends the owner's manual, fuse-box lid diagram, or a year-specific wiring diagram before replacing parts .
3. Some discussions refer to more than one relay in the fuel pump circuit. A Ford truck forum discussion about a 2001 F-250 described an under-hood relay near the driver-side firewall and another relay behind the radio . That report is not a 1999 chart, but it shows why two owners can both be right while talking about different relay positions or different truck configurations.
4. Previous repairs can change what you see. A 26-year-old work truck may have had a replacement fuse box, a wiring repair, an aftermarket alarm, a remote start system, or a relay moved by a previous owner. If the under-hood label does not match the manual, take a clear photo and compare it with VIN-specific information before pulling parts.
The practical answer: check the under-hood box first. If your VIN, build date, or owner's manual identifies a dash-mounted relay, inspect the center dash area near the radio only after you have confirmed that your truck uses that layout. Do not remove the radio simply because a forum post says to do so.
3. What the Fuel Pump Relay Actually Does
The relay is an electrically controlled switch. It allows a low-current control circuit, usually managed by the PCM or ignition circuit, to turn a higher-current circuit on and off for the fuel pump . When the relay is commanded on, battery power can reach the pump. When it is off, the pump should not keep running with the key off .
On a truck that cranks normally, the first clue is often sound. Turn the key to ON without cranking and listen near the fuel tank or fuel filler area. Many electric pumps run briefly to prime the system. If you hear nothing, the pump may be bad, but it may also have no power because of a fuse, relay, PCM power problem, inertia switch, connector, or broken wire . That is why the pump should not be the first part you buy.
A bad relay can produce these symptoms:
- Crank, no start. The starter spins the engine, but there is no fuel pressure.
- No pump prime sound. The pump stays silent with the key turned to ON.
- Intermittent starting. The truck starts one day and refuses the next, especially if the relay contacts are worn or heat-sensitive.
- Start, then stall. Power to the pump drops out after the initial prime.
- No fuel pressure at the test port. A gasoline truck may show little or no pressure at the fuel rail Schrader valve when the pump circuit is dead .
Those symptoms also fit a blown fuse, tripped inertia switch, weak battery, damaged harness, bad pump, or PCM power problem, so testing matters .
4. Tools That Make the Job Easier
You do not need a full shop for the first round of checks.
1. Owner's manual or a VIN-specific wiring diagram. Use it to confirm fuse numbers, relay labels, and wire colors .
2. A digital multimeter or a 12-volt test light. A multimeter lets you check battery voltage, fuse voltage, ground, and voltage at the pump connector. A test light is useful for a quick power check, but it does not replace careful voltage testing.
3. A fuse puller or needle-nose pliers. Use the correct tool so you do not crack nearby plastic or damage terminals.
4. A known-good relay with the exact same part number and terminal layout. A relay that physically plugs in is not automatically correct. KEMSO's 7.3L guide recommends using a known-good relay of the exact same part number as a test part and warns that cheap relays of uncertain quality can create a new problem .
5. A fuel pressure gauge for gasoline engines. The Schrader valve on the fuel rail gives you a direct pressure reading instead of a guess .
6. Basic safety gear. Safety glasses, gloves, a fire extinguisher rated for automotive fires, and good ventilation are sensible whenever you work around fuel and electricity.
5. A Practical Diagnostic Order
Follow this order so a cheap electrical problem does not turn into an unnecessary fuel tank job.
1. Write down the symptom. Note whether the engine cranks, how long it cranks, whether it starts and stalls, whether the check engine light or Wait to Start light behaves normally, whether the problem happens hot or cold, and whether it began after refueling, a fuel filter change, a hard bump, or trailer wiring work. KEMSO's 7.3L guide recommends describing the symptom before touching parts because a clear record prevents random parts replacement .
2. Check the batteries and cable connections. The 7.3L diesel needs strong cranking speed, and a guide for those trucks recommends checking both batteries because weak batteries can give confusing scan data and prevent a proper start even when the fuel system is fine . Low system voltage can also make a relay chatter or make a pump sound weak.
3. Check the inertia fuel shutoff switch. Ford uses this safety device to stop fuel pump power after a hard impact. Ford truck owners commonly describe it behind the passenger-side kick panel in the front footwell, with a reset button on top . A 1999 F-250 owner specifically mentioned checking the inertia switch while diagnosing a pump that would not run . Press the reset button only after you have checked for fuel leaks, damaged lines, and the smell of gasoline or diesel. If you smell fuel, stop and get professional help.
4. Inspect both fuse panels. Check the under-hood Power Distribution Box and the interior panel below and left of the steering wheel . On the 1999 Super Duty chart, pay particular attention to under-hood fuses 5, 19, 20, 24, and 30, plus interior fuses related to PCM power and starter relay coil circuits . Replace a blown fuse only with the same amperage rating. If a new fuel pump fuse blows again, do not keep installing fuses; there is a circuit fault that needs to be found .
5. Verify the relay location and identity. Read the lid diagram and compare it with the year-specific manual. On the published 1999 Super Duty chart, R32 is the two-speed fuel pump relay on gasoline trucks, while diesel trucks list R32 as the Injector Driver Module Power Relay . Do not pull several identical relays at once and mix their positions. Mark each relay before removal or remove only one at a time .
6. Try a known-good identical relay as a test. Switch the ignition off, swap in a relay with the same part number and terminal pattern, then turn the key to ON and listen for pump prime. If the pump runs and the truck starts, the original relay is a strong suspect. This is a test result, not a complete circuit diagnosis .
7. Check for power and ground at the pump. If the relay clicks and power leaves the box but the pump connector has no voltage, trace the harness and connectors. If the pump connector has proper power and ground and the pump still does not run, the pump itself becomes the likely fault . A 1999 F-250 owner measured only 4.6 volts at one wire on the pump connector while diagnosing a no-start, which shows why a direct circuit measurement is useful .
8. Measure fuel pressure on gasoline engines. A fuel pressure gauge at the rail tells you whether the pump is building pressure. A forum write-up on a 1999–2007 F-250 fuel pump replacement describes pressing the Schrader valve on the passenger-side fuel rail to see if fuel appears with the key in the ON position, then checking the fuse and relay if there is no pressure . Use a proper gauge rather than an open flame or loose fuel spray.
9. Scan for codes before clearing anything. Codes can point to PCM power, fuel pump circuit, injector, or sensor faults, but a code still requires circuit testing. KEMSO's 7.3L guide states that a diagnostic code such as P0231, which relates to a fuel pump circuit condition, still requires checking battery voltage, inspecting fuses, and measuring the pump circuit .
6. Gasoline F-250 Versus 7.3L Power Stroke
The keyword "99 F250 fuel pump relay location" covers several engines, and the answer changes with the engine.
For gasoline trucks, published 1999 Super Duty fuse charts list under-hood fuse 5 as a 20A circuit for the PCM, two-speed fuel pump relay coil, fuel pump relay coil, mass air flow sensor, and injectors. Fuse 19 is a 20A MAXI fuse for the fuel pump motor and PCM, and relay R32 is the two-speed fuel pump relay . On a gasoline truck, the fuel rail test port and a fuel pressure gauge are useful tools .
For 7.3L Power Stroke diesel trucks, the same under-hood relay position is described as the Injector Driver Module Power Relay in published fuse charts . A KEMSO guide for 1999–2003 Super Duty trucks says many of them have the fuel pump relay in the under-hood Power Distribution Box, but some model years and cab or chassis configurations use a different relay layout . It also warns that a pump that stays off with the key on can be caused by a blown fuse, no PCM power, a missing Wait to Start light, a shorted fuel bowl heater circuit, damaged wiring, or missing PCM signals .
For a 7.3L no-start, use the diesel-specific checks:
- Confirm adequate cranking speed and strong batteries.
- Watch for the Wait to Start light. If it does not come on, check PCM fuses, PCM relay, and related power circuits before blaming the fuel pump relay .
- Check whether the fuel bowl refills after draining the bowl or changing the filter. If it does not refill, investigate pump power and supply. If it does refill, move on to ICP, RPM signal, injector command, and glow system .
- Remember that a 7.3L no-start generally depends on adequate cranking speed, fuel, high-pressure oil, and injector command .
That distinction saves money. Replacing an in-tank electric pump will not fix a 7.3L truck that has no PCM power, no injector command, or a high-pressure oil problem.
7. Relay Testing Without Damaging the Truck
A relay has a control side and a load side. You do not need to memorize a pin chart from the internet; you need the wiring diagram for your VIN and a careful test.
1. Check for battery voltage at the supply side of the relay socket. With the correct diagram and safe probe placement, one terminal should have battery power at all times or whenever the relevant ignition feed is active.
2. Check the control signal. The PCM or ignition circuit must command the relay. If the relay never receives a command, replacing it will not help.
3. Check the relay coil and ground. A missing ground or open coil keeps the switch from closing.
4. Check the output to the pump circuit. If the relay clicks and the supply side has power but there is no output, the relay contacts may be burned or the socket may be loose.
5. Check voltage drop under load. A corroded connector can show nearly normal voltage with no load and lose voltage when the pump is connected. Inspect for green corrosion, pushed-out pins, loose female terminals, melted plastic, and water in the box .
6. Inspect the harness near the tank and frame. A work truck can have chafed wiring from road debris, trailer work, a tank removal, or a previous repair. A guide for F-250 relay diagnosis says that if the relay clicks and sends power but the pump connector has no power, the harness and connectors should be traced .
Avoid jumping power directly to the pump for anything more than a brief controlled test. A jumper bypasses fuses, relays, and safety devices. If you are not trained to do that test, use a multimeter or have a professional perform it.
8. Signs the Problem Is Not the Relay
A relay is cheap, so people replace it first. That is fine as a test, but it is not always the repair.
Look elsewhere when you find these results:
- The fuel pump fuse is blown again immediately. This points to a short or an overloaded circuit, not simply a weak relay .
- A known-good identical relay changes nothing. Check fuses, PCM power, the inertia switch, wiring, and pump power.
- The relay clicks but the pump connector has no power. Trace the harness and connectors .
- The pump connector has correct power and ground but the pump does not run. The pump is the likely fault .
- The pump runs and the fuel bowl fills but a 7.3L still will not start. Move to ICP, injector command, IDM, glow system, compression, and scan data .
- The truck loses power only when hot, while towing, or after an hour of driving. A pump that weakens with heat, a restricted filter, or a supply problem may be involved. One 1999 F-250 V10 owner described losing idle and fuel pressure after about an hour of towing, then restarting after a cool-down period .
- The Wait to Start light is out on a 7.3L. Check PCM power before the pump relay .
9. How to Replace a Confirmed Bad Relay
Once testing confirms the relay, the replacement is usually simple.
1. Buy the correct part. Match the Ford or Motorcraft part number, terminal pattern, amperage rating, year, engine, and chassis configuration. KEMSO's 7.3L guide specifically warns that a relay that physically plugs in is not automatically electrically correct .
2. Disconnect power. Switch the ignition off and remove the key. If you are working on wiring or connectors beyond a simple relay swap, disconnect the negative battery cable.
3. Pull the old relay straight out. Grip the body, not the wires. Wiggle gently if the terminals are tight. Do not pry hard against neighboring fuses.
4. Inspect the socket. Look for spread terminals, heat marks, corrosion, water, and a loose relay fit. A relay that feels loose can cause an intermittent no-start.
5. Push in the new relay fully. Make sure it seats squarely and sits at the same height as the others.
6. Reconnect power and test. Turn the key to ON, listen for the pump prime, check for leaks, then start the engine. Confirm smooth idle and a normal road test.
7. Recheck the fix after a heat soak. Intermittent relay faults often show up after the truck gets hot. Start it again after a drive and after it sits for 20 to 30 minutes.
10. If the Fuel Pump Is Actually Bad
The electric fuel pump on a 1999 F-250 is commonly located inside the fuel tank, according to a 2CarPros answer about a 1999 Ford F-250; that answer says access usually means dropping the tank or pulling the bed . Before doing that job, confirm that the pump has proper power and ground and that pressure is below specification .
A practical replacement checklist:
1. Verify fitment by VIN, year, engine, cab style, bed length, and tank size. Do not order from a generic "1999 F-250" listing without checking the application.
2. Relieve fuel system pressure. Follow the service manual procedure for your engine.
3. Disconnect the battery. Keep sparks, cigarettes, heaters, and open flames away from the work area.
4. Support the truck and tank correctly. Use a rated jack and jack stands. Never rely on a hydraulic jack alone.
5. Keep the work area ventilated. Fuel vapor is heavier than air and can collect in low spots.
6. Inspect the tank, strainer, filter, and connector. Replace a damaged connector rather than reusing a melted or corroded one.
7. Install a new strainer and seals as required. Reusing a swollen or pinched seal can cause a fuel smell or an evaporative emissions code.
8. Cycle the key several times to prime the system. Check for leaks before cranking.
9. Recheck fuel pressure and scan data. Clear codes only after recording them and finishing the repair.
11. Common Parts-Store Mistakes
1. Using a 2002 or 2005 fuse chart for a 1999 truck. Fuse numbers and relay labels change by year and engine .
2. Assuming every 1999 F-250 is a Super Duty. The 1999 model year included different F-250 versions, and published fuse diagrams reflect that split .
3. Swapping a relay with one that only looks the same. Match the part number and pin layout .
4. Replacing a pump because there is no hum at the tank. No sound can mean no power at the pump, not a dead pump .
5. Ignoring the inertia switch. Ford truck owners commonly identify it behind the passenger-side kick panel, and a 1999 F-250 no-start thread shows an owner checking it early in diagnosis .
6. Clearing codes before writing them down. Codes help you find the circuit that failed.
7. Installing a higher-amp fuse. The fuse protects the wiring. A larger fuse can allow the harness to overheat.
8. Forgetting the PCM power circuit. On a 7.3L, no Wait to Start light can point to a PCM power issue rather than a pump problem .
12. Maintenance Habits That Help an Older F-250
1. Keep the fuel tank above empty when practical. Fuel helps cool the in-tank electric pump, and KEMSO's maintenance guidance says running the tank dry shortens pump life .
2. Replace the fuel filter on schedule. KEMSO's guide notes that a clogged filter makes a lift pump work harder and starves the high-pressure pump .
3. Buy fuel from busy, high-volume stations. Clean fuel matters, and the same KEMSO guide recommends busy stations for diesel trucks .
4. Fix weak grounds and corroded connectors promptly. KEMSO warns that a failing module or weak ground can burn out a new pump just like the old one .
5. Keep the Power Distribution Box cover secured. Water, road salt, and dirt at relay terminals can create intermittent electrical faults. KEMSO's roadside checklist includes inspecting the Power Distribution Box for water and loose relays .
6. Keep a small diagnostic kit in the truck. A multimeter, fuse chart, spare correct relays, spare correct fuses, gloves, and a flashlight are useful on a work truck or tow vehicle.
7. Save repair records. KEMSO recommends keeping the installation date and part details, especially if a warranty claim comes up later .
13. Recommend KEMSO Fuel Pumps
If testing confirms that the relay, fuses, inertia switch, wiring, and PCM power circuits are good and the fuel pump itself has failed, we recommend buying a KEMSO Fuel Pump. KEMSO Fuel Pump products are built as high-performance OEM replacement parts. They are designed to meet or exceed original equipment specifications for fit, flow, and pressure so the pump works correctly with the factory fuel system and factory wiring . KEMSO also offers high-performance pumps and direct OEM replacement pumps for a wide range of vehicles, with designs that fit standard mounting locations .
Every KEMSO Fuel Pump comes with a lifetime warranty. That gives the owner long-term support and makes the purchase a practical choice for a truck used for towing, hauling, jobsite work, and daily driving . KEMSO's broader pump information also describes high-performance construction, consistent pressure delivery, and OEM replacement compatibility . When you order, check the exact application by year, engine, and VIN, and confirm that the connector, pressure rating, flow rating, and mounting match your 1999 F-250.
Visit the official KEMSO website to see the full product range and find the correct pump for your truck: https://www.kemsoracing.com/
14. Short Roadside Checklist
1. Set the parking brake and put the transmission in Park or Neutral.
2. Note whether the dash lights and, on a 7.3L, the Wait to Start light behave normally. KEMSO's roadside checklist includes noting the Wait to Start light and checking battery voltage and cable connections .
3. Check battery voltage and terminals.
4. Open the under-hood Power Distribution Box and inspect for water, loose relays, corrosion, and a missing or damaged cover. KEMSO's checklist includes inspecting the Power Distribution Box for water and loose relays .
5. Check the fuel pump and PCM fuses for the 1999 Super Duty layout, especially under-hood fuses 5 and 19 .
6. Check the inertia fuel shutoff switch behind the passenger-side kick panel area, but only after checking for leaks and fuel smell .
7. Verify relay R32 against the lid diagram and your VIN-specific information .
8. Swap only with a known-good relay of the exact same part number and terminal layout .
9. Listen for pump prime with the key in the ON position.
10. Check power and ground at the pump connector before ordering a pump .
15. Frequently Asked Questions
1. Where is the fuel pump relay on a 1999 F-250 Super Duty?
Most commonly, the relevant relay circuit is in the under-hood Power Distribution Box on the driver side of the engine bay near the firewall. Published 1999 Super Duty charts label R32 as the Two Speed Fuel Pump Relay on gasoline trucks and the Injector Driver Module Power Relay on diesel trucks . Confirm with the lid diagram or owner's manual because configuration matters .
2. Why do some people say the relay is behind the radio?
Some 1999 F-250 owner reports describe a relay behind the lower center dash near the radio or ashtray, while other 1999 F-250 Super Duty owners report the under-hood driver-side firewall location . The split between light-duty and Super Duty models, engine differences, and configuration changes are likely reasons for the conflicting answers. VIN-specific documentation is the safest way to settle it .
3. Which fuse powers the fuel pump?
For the published 1999 Super Duty diagram, under-hood fuse 19 is a 20A MAXI fuse for the Fuel Pump Motor and PCM, while under-hood fuse 5 is a 20A MINI fuse for the PCM and fuel pump relay coil circuits on gasoline engines . Verify the number on your own truck before replacing anything .
4. Can a bad relay cause a crank-no-start?
Yes. A failed relay can stop power from reaching the pump . A no-start can also come from a blown fuse, tripped inertia switch, no PCM power, damaged wiring, a weak battery, or a failed pump .
5. Should I swap the fuel pump relay with the horn relay?
Only if the part number and terminal layout are identical and the diagram confirms that the other relay is safe to use for a brief test. KEMSO recommends a known-good relay of the exact same part number and warns that a relay that fits is not always electrically correct . Do not mix several relays or leave an incorrect relay installed.
6. Does a 1999 F-250 have a fuel pump driver module?
One discussion about a 1999 F-250 intermittent no-start includes an owner looking for an FPDM near the spare tire and a reply stating that there is no module on that year . Treat that as an owner discussion, not a factory specification, and confirm with a VIN-specific wiring diagram if your truck has been modified.
7. Where is the fuel pump itself?
A 2CarPros answer about a 1999 Ford F-250 says the electric pump is in the fuel tank and is usually accessed by dropping the tank or pulling the bed . Confirm the tank arrangement before ordering parts.
8. What if the new fuel pump fuse keeps blowing?
Stop replacing fuses. A repeated blown fuse points to a short or overloaded circuit that needs testing . Check the pump harness, relay socket, connectors, and any damaged sections of wire along the frame.
9. What should I check on a 7.3L Power Stroke before buying a pump?
Check batteries, cranking speed, Wait to Start light, PCM power, fuses, relay circuit, fuel bowl refill, wiring, high-pressure oil, and injector command . A silent pump alone does not prove the pump is bad.
10. What is the safest first move if I am stuck in a parking lot?
Check for fuel smell or visible leaks first. If everything is dry, check battery connections, the inertia switch reset button, the related fuses, and the Power Distribution Box for loose relays or water . If the truck still will not start, have it towed rather than bypassing safety circuits.
Final Answer
For the search 99 f250 fuel pump relay location, start at the under-hood Power Distribution Box on the driver side near the firewall on a 1999 F-250 Super Duty . Match the cover diagram to a 1999-specific chart, check relay R32 and the fuel pump or PCM fuses listed for your engine, and remember that some 1999 F-250 owner reports point to a relay near the center dash or radio . Test the circuit before replacing the pump. If the pump is confirmed bad, choose a high-performance OEM replacement KEMSO Fuel Pump backed by a lifetime warranty and verify the exact fitment for your truck.