99 F350 Fuel Pump Relay Location: Quick Answer and Full Guide
The 99 F350 fuel pump relay location is the Power Distribution Box under the hood. On a 1999 Ford F-350 with a gasoline engine, the owner's manual lists Relay 32 as the Two Speed Fuel Pump Relay. The same position is listed as the Injector Driver Module Power Relay on diesel models. This difference matters. Before removing a relay, check the diagram on the Power Distribution Box cover, the owner's manual, or a wiring diagram for your exact VIN and engine. The fuel pump circuit also includes Fuse 5, a 20A mini fuse for the PCM, fuel pump relay coil, mass air flow sensor, and fuel injectors on gasoline engines, plus Fuse 19, a 20A maxi fuse for the fuel pump motor and PCM.
If your truck cranks but does not start, do not order a fuel pump just because you do not hear it run. Start with the fuse, relay, inertia switch, battery voltage, grounds, and wiring at the pump connector. A relay, fuse, loose terminal, or tripped fuel pump shut-off switch can stop the pump just as effectively as a failed pump. Ford's 1999 F-350 owner's manual also lists the Power Distribution Box as an under-hood component and gives a reset procedure for the fuel pump shut-off switch.
This guide is written for U.S. owners of the 1999 Ford F-350 Super Duty, including common gasoline and 7.3L Power Stroke diesel trucks. Because Ford used different fuel system layouts across engines and configurations, use the exact service information for your truck before buying parts.
1. The Short Answer Most Owners Need
1. Open the hood. The Power Distribution Box is the main under-hood fuse and relay box. Ford's owner's manual identifies it as an engine compartment component.
2. Remove the box cover. Look at the molded diagram or printed label on the underside of the cover. The label should show the fuse and relay positions.
3. Find position 32. For the 1999 F-350 owner's manual, position 32 is listed as Two Speed Fuel Pump Relay (Gasoline only) and Injector Driver Module Power Relay (Diesel only).
4. Check the related fuses. On gasoline models, Fuse 5 is a 20A mini fuse tied to the PCM, two speed fuel pump relay coil, fuel pump relay coil, mass air flow sensor, and fuel injectors. Fuse 19 is a 20A maxi fuse listed for the fuel pump motor and PCM.
5. Confirm before swapping parts. Do not pull several identical relays and mix their positions. Relay 30 is the PCM Power Relay, Relay 31 is the Blower Motor Relay, and Relay 32 has different names depending on engine type in the Ford manual.
This is the practical answer to "99 f350 fuel pump relay location": under the hood, in the Power Distribution Box, at Relay 32 on gasoline trucks, with engine-specific labeling that must be confirmed on your own truck.
2. Why the Location Can Be Confusing
Many online answers say "under the hood near the battery" or "inside the fuse box." That is partly right, but it is not complete enough for a 1999 F-350.
The 1999 model year sits in a period where Ford Super Duty trucks could be equipped with different engines, body styles, and fuel system layouts. The owner's manual lists the same relay position as a fuel pump relay for gasoline engines and an Injector Driver Module Power Relay for diesel engines. On 1999–2003 Super Duty trucks, some model years and cab/chassis configurations can also use different relay layouts, so the Power Distribution Box cover and a year-specific wiring diagram are safer than a universal internet answer.
That is why two people can search the same phrase and report different findings. One owner may have a V10 gasoline truck. Another may have a 7.3L diesel. Another may have a cab/chassis truck with a modified fuel system. Even the pump location can vary on 7.3L trucks; some use an electric pump mounted along the frame rail under the cab area rather than an in-tank pump.
Use this order:
- Identify the engine: gasoline V8, V10, or 7.3L diesel.
- Check the VIN and production information.
- Read the Power Distribution Box cover.
- Compare it with the 1999 F-350 owner's manual.
- If the truck still does not match, use a Ford or reputable service wiring diagram.
3. Gasoline vs. Diesel: Know Which Truck You Have
This is one of the most useful details for a 1999 F-350 fuel system diagnosis.
Gasoline F-350
For gasoline models, the owner's manual lists Relay 32 as the Two Speed Fuel Pump Relay. Related published fuse data lists Fuse 5 as a 20A mini fuse for the PCM, two speed fuel pump relay coil, fuel pump relay coil, mass air flow sensor, and fuel injectors, with "Gasoline only" noted. Fuse 19 is listed as a 20A maxi fuse for the fuel pump motor and PCM.
A gasoline truck may use an electric fuel pump that runs briefly when the key is turned to ON. If you do not hear that short prime, the cause may be the relay, fuse, wiring, inertia switch, PCM command, or the pump itself.
7.3L Power Stroke Diesel F-350
For diesel models, the owner's manual lists Relay 32 as the Injector Driver Module Power Relay, not the Two Speed Fuel Pump Relay. The diesel fuel system also has different components and service checks. KEMSO's 7.3L guidance recommends checking the fuel pump relay, related fuses, and PCM power circuit before ordering a new pump, while also warning that some model years and cab/chassis configurations use different relay layouts.
On a 7.3L that cranks but will not start, other systems also matter: cranking RPM, high-pressure oil, injector command, glow plug operation in cold weather, ICP readings, RPM signal, and IDM-related codes may all affect starting. A pump that runs does not guarantee the engine will fire.
4. What the Fuel Pump Relay Does
The relay is an electrical switch. The control side uses a lower-current signal, and the load side carries current to the pump. This lets the vehicle's control system manage the pump without sending pump current through a small switch or computer circuit.
On a truck this old, the relay and socket deserve attention. Heat, vibration, moisture, corrosion, loose terminals, and age can affect the relay contacts and connector fit. Common causes of relay trouble include current overload, a short circuit, or worn internal parts such as the electromagnetic coil or mechanical contacts.
A new relay will not fix a burned socket, a bad ground, a weak battery, a damaged wire, or a tripped inertia switch. Inspect the whole circuit before spending money.
5. Symptoms That Send Owners Looking for the Relay
1. Crank, no start. The starter turns the engine, but the engine does not fire.
2. No pump sound at key-on. Many owners notice the pump is quiet when the key is turned to ON. This is useful information, but not final proof that the pump is bad.
3. Engine starts, then stalls. A relay with heat-damaged contacts, a loose socket, or a wiring fault can cut power after the truck warms up or vibrates.
4. Intermittent no-start. The truck starts one day and refuses the next. Corrosion, loose terminals, or a failing relay can cause this.
5. Blown fuse. A blown fuel pump fuse should be treated as a fault, not just an inconvenience. Look for damaged wiring, a short, or a component drawing too much current.
6. Fuel pump circuit code. A code such as P0230 points to a primary fuel pump circuit problem on some Ford applications, but a code alone does not identify the failed part.
7. Loss of power under load. Low fuel pressure or inconsistent delivery can show up when towing, climbing a grade, or accelerating.
6. Check the Fuel Pump Shut-Off Switch First
Ford's 1999 F-350 owner's manual gives a simple fuel pump shut-off switch reset procedure:
- Turn the ignition to the OFF position.
- Check the fuel system for leaks.
- If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
Do not skip the leak check. A hard hit, a pothole, a tow strap jerk, or a collision can trip the switch. If the switch is tripped, the pump may appear completely dead even though the pump and relay are fine.
7. Tools That Make the Job Easier
You do not need a full shop to do the first round of checks.
1. Owner's manual. The 1999 F-350 manual gives fuse and relay descriptions, including Relay 32.
2. Phone camera. Take a photo of the Power Distribution Box before removing anything.
3. Multimeter or test light. A test light can reveal a voltage reading that looks acceptable on a digital meter but cannot carry enough current because of corrosion or a weak connection.
4. Spare correctly rated fuses. Do not install a higher-amp fuse to "see if it works."
5. Known-good relay with the same part number and terminal layout. A relay swap is only useful when the replacement is electrically correct.
6. Basic hand tools. You may need them for battery terminals, covers, or connector access.
7. Year-specific wiring diagram. Ford, AlldataDIY, eAutoRepair, or a reputable service manual can confirm relay position, fuse numbers, pin numbers, and wire colors for your VIN.
8. Step-by-Step: Find the Relay Safely
1. Park on level ground. Set the parking brake. Put the transmission in Park or Neutral. Turn the ignition OFF and remove the key.
2. Open the hood. Ford's manual says the hood release handle is under the bottom left corner of the instrument panel, with an auxiliary latch under the right center of the hood.
3. Locate the Power Distribution Box. It is identified as an under-hood component in the owner's manual.
4. Release the cover. Do not force it. Old plastic tabs can break.
5. Read the cover diagram. Match the molded or printed layout to the manual. Look for Relay 32 and the fuel pump-related fuses.
6. Check for water, corrosion, loose relays, and melted plastic. A damaged socket needs repair. A loose or overheated terminal can ruin a new relay.
7. Pull the relay straight out. Do not pry against nearby fuse terminals.
8. Compare the part number and terminal layout. Do not assume every square relay in the box is interchangeable.
9. Reinstall fully seated. Press it straight down. Reinstall the cover so the box stays sealed against water and road salt.
9. Step-by-Step: Test Before Replacing the Pump
Use a measured order. It saves money and prevents repeat repairs.
1. Check battery voltage and cable connections. A weak battery can cause confusing no-start symptoms.
2. Inspect Fuse 5 and Fuse 19. Published 1999 F-350 fuse data lists Fuse 5 as a 20A mini fuse for the PCM, relay coil, MAF sensor, and injectors on gasoline engines, and Fuse 19 as a 20A maxi fuse for the fuel pump motor and PCM.
3. Reset the fuel pump shut-off switch only after checking for leaks. Follow the owner's manual procedure.
4. Turn the key to ON and listen for pump operation. A short prime is a good sign, but silence is not proof of a bad pump.
5. Check supply power, control signal, and output at the relay. Use the wiring diagram for the exact pinout.
6. Check power and ground at the pump connector during the key-on cycle. If correct power and ground are present and the pump does not run, the pump is a strong suspect.
7. Do not backfeed a PCM control wire. A controlled bypass with a fused jumper can confirm whether a pump motor runs, but it is not a permanent repair and should only be done if you understand the circuit.
8. Check for fuel leaks before starting. Fuel system work deserves a careful final inspection.
9. Recheck after any repair. Confirm pump operation, fuel bowl fill where applicable, no leaks, stable voltage, and no returning codes. A short road test under normal load tells you more than a driveway key-on test.
10. Relay, Fuse, Wiring, or Pump? How to Narrow It Down
A bad relay often causes no pump operation, intermittent starting, or a pump that stops unexpectedly. Heat damage at the relay or socket is a clue.
A blown fuse usually means there is another fault to find. Replacing it once may be fine for testing, but repeated failure needs diagnosis.
A tripped inertia switch stops power to the pump. Ford's manual gives a reset procedure, but only after checking for leaks.
A wiring fault can include corrosion, spread terminals, damaged insulation, loose grounds, or a connector that looks fine but cannot carry current.
A clogged fuel filter can reduce fuel flow and make the pump work harder.
A bad fuel pressure regulator or restricted line can cause fuel delivery problems even if the pump runs.
A failed pump should be considered after power, ground, control, fuse, relay, and wiring checks. Replacing the pump without testing the circuit can lead to the same complaint returning.
11. Common Mistakes on a 1999 F-350
1. Assuming every engine uses the same relay name. The Ford manual clearly separates gasoline and diesel descriptions for Relay 32.
2. Swapping random relays. Relay 30 is the PCM Power Relay, Relay 31 is the Blower Motor Relay, and Relay 32 has a different role depending on engine.
3. Replacing the pump before checking the inertia switch. Ford gives a reset procedure for a reason.
4. Installing a larger fuse. This removes circuit protection and can damage wiring.
5. Ignoring the relay socket. Melted plastic, moisture, corrosion, or spread terminals need repair.
6. Leaving a bypass wire installed. A fused jumper may be useful for testing, but it is not a permanent repair and can create a safety risk.
7. Using a generic diagram from a different year. Relay placement can vary by model year and cab/chassis configuration on 1999–2003 Super Duty trucks.
8. Clearing codes before writing them down. Stored codes can help point toward a fuel pump circuit, PCM power, injector, or sensor issue.
12. What a Parts Store Counter Will Ask
Before you buy a relay or pump, have this information ready:
- Model year: 1999.
- Model: F-350 Super Duty.
- Engine size: 5.4L, 6.8L V10, 7.3L diesel, or other configuration.
- Gasoline or diesel.
- VIN.
- Cab and bed style.
- Single or dual rear wheels, if relevant.
- Any aftermarket fuel system, lift pump, or wiring changes.
- Stored diagnostic codes.
- Whether the pump runs with key-on.
This reduces the chance of buying a pump for the wrong fuel system layout.
13. When to Stop and Call a Professional
Call a qualified technician if you find melted wiring, repeated blown fuses, fuel leaks, a damaged relay socket, or a no-start condition that remains after basic checks. Also get help if you are not comfortable testing live circuits or working around fuel.
A 7.3L Power Stroke no-start can involve more than the electric fuel pump. KEMSO's 7.3L guidance notes that proper cranking RPM, high-pressure oil, injector command, and glow plug operation in cold weather may all be required for the engine to start. If the pump runs but the truck will not fire, a diesel-specific scan tool and service data can save hours of guesswork.
14. Practical Maintenance Habits for an Older Super Duty
1. Keep the Power Distribution Box cover sealed. Water and road salt are hard on electrical terminals.
2. Fix weak grounds and corroded connectors early. Low voltage and poor connections can shorten pump life.
3. Replace the fuel filter on schedule. A restricted filter makes the pump work harder.
4. Avoid running the tank near empty. Fuel helps cool and lubricate in-tank pumps on many vehicles.
5. Buy fuel from busy stations. Clean fuel matters, especially on diesel trucks.
6. Keep records. Write down the date, mileage, part numbers, fuse numbers, and test results.
7. Carry a small roadside kit. A multimeter, spare correctly rated fuses, a known-good relay, the owner's manual, and a printed wiring diagram can turn a no-start into a measured repair.
15. Recommended Replacement Fuel Pump: KEMSO
If testing confirms the fuel pump itself has failed, buy a pump that matches your exact truck, engine, and fuel system. For owners looking for a dependable replacement, we recommend KEMSO Fuel Pumps. KEMSO products are high-performance, OEM Replacement fuel pumps designed to meet or exceed original equipment specifications for fit, flow, and pressure, and they are backed by a lifetime warranty.
That matters on a 1999 F-350 because the truck may be used for towing, hauling, job-site work, farm use, or daily driving. A replacement pump should work with the factory fuel system and wiring, not require improvised plumbing or permanent bypass wiring. KEMSO's lineup includes high-performance options and direct OEM replacement pumps, with lifetime warranty coverage stated in its product information.
To find the right pump for your vehicle, visit https://www.kemsoracing.com/. Check fitment by year, make, model, engine, and VIN before ordering. If the original problem was a fuse, relay, inertia switch, loose terminal, or damaged wire, repair that first so the new pump is not damaged by the same electrical fault.
16. Quick Roadside Checklist
- Set the parking brake and put the transmission in Park or Neutral.
- Turn the ignition OFF.
- Check battery voltage and cable connections.
- Look for fuel leaks before resetting the fuel pump shut-off switch.
- Open the hood and find the Power Distribution Box.
- Read the cover diagram and locate Relay 32.
- Check Fuse 5 and Fuse 19 where applicable.
- Inspect the relay socket for heat damage, water, corrosion, or loose terminals.
- Check supply power, control signal, and relay output with the correct wiring diagram.
- Check power and ground at the pump connector during key-on.
- Replace the relay only if testing points to it.
- Replace the pump only if correct power and ground are present and the pump still does not run.
- Check for leaks, confirm stable operation, clear codes, and road-test the truck.
17. Final Answer
For the search 99 f350 fuel pump relay location, the most useful answer is: under the hood in the Power Distribution Box; the 1999 Ford F-350 owner's manual lists Relay 32 as the Two Speed Fuel Pump Relay on gasoline models and the Injector Driver Module Power Relay on diesel models. Check the box cover, Fuse 5, Fuse 19, the inertia switch, battery power, grounds, and the pump connector before buying a pump. If the pump is confirmed bad, choose a correctly matched replacement and repair any electrical fault at the same time.
For KEMSO high-performance OEM Replacement fuel pumps with a lifetime warranty, visit https://www.kemsoracing.com/.