99 Ford Expedition Fuel Pump Relay Location: Quick Answer and Full Guide
The fuel pump relay on a 1999 Ford Expedition is in the Power Distribution Box under the hood, on the driver's side of the engine compartment, near the brake master cylinder. It is commonly identified as relay #301. The fuel pump fuse is in the same box, usually listed as a 20-amp mini fuse in position #10. If your Expedition cranks but will not start, check the fuse, relay, inertia switch, and wiring before buying a fuel pump. A bad relay can create the same no-start symptoms as a failed pump, so confirming power at the relay and pump circuit first can save real time and money.
This guide is written for U.S. owners of the first-generation Ford Expedition, especially the 1999 model with the 4.6L or 5.4L V8. It covers where to look, how to identify the correct relay, what symptoms point to a relay problem, how to test the circuit, when the pump itself is likely at fault, and what to consider before replacing parts. The steps use common shop tools and follow a practical order: start with easy checks, then move toward deeper diagnosis.
1. Where the Relay Is Located
1. Open the hood. The 1999 Expedition has a main fuse and relay box in the engine bay. Ford service information and fuse diagrams refer to this box as the Power Distribution Box or Battery Junction Box. It is not the small interior fuse panel near the driver's lower dash area.
2. Look on the driver's side of the engine compartment. The under-hood box sits near the brake master cylinder area on many 1997–2002 Expeditions. Some diagrams describe the same area as the driver-side engine compartment power distribution box.
3. Remove the black plastic cover. The cover usually has a diagram or at least molded labels. On an older truck, the printed chart may be faded, missing, or hard to read in low light. Use the owner's manual or a reliable fuse diagram for the 1999 model year if the cover legend is unclear.
4. Find relay #301. Several 1999 Expedition fuse listings identify Relay 301 as the Fuel Pump Relay. Some aftermarket diagrams also show a fuel pump relay in the engine-compartment power distribution box, so the exact numbering can vary by diagram version and production layout. When in doubt, match the cover legend, owner's manual, and relay part number rather than guessing by position alone.
5. Find the related fuses. Published 1999 Expedition fuse listings commonly show a 20A fuel pump fuse and a 15A fuse for the PCM, injectors, fuel pump circuit, and mass air flow sensor. The 20A fuse is often shown as position #10 in the power distribution box. Do not replace a blown fuse with a higher-amp fuse. If it blows again, there may be a short or an overloaded pump circuit that needs diagnosis.
2. Why the Location Confuses So Many Owners
1. There is more than one fuse panel. A first-generation Expedition has a passenger-compartment fuse panel and one or more engine-compartment fuse/relay boxes depending on equipment. The interior panel is below and to the left of the steering wheel near the brake pedal on these models. That panel is useful for accessories, but the main fuel pump relay is generally associated with the under-hood power distribution box.
2. Online diagrams are not all identical. Some pages group 1997–2002 trucks together. Others show different box versions, early production layouts, or related minifuse panels. That is why a diagram for a 2001 or 2002 Expedition should not be treated as automatic proof for a 1999 truck. Use the year-specific owner's manual when possible.
3. Some later Expedition models use different fuel control parts. Discussions about 2003–2004 Expeditions often mention a fuel pump driver module or an internal relay in the fuse box. Those details can be relevant to newer trucks, but they should not be applied blindly to a 1999 Expedition. For the 1999 model, the practical starting point remains the under-hood power distribution box, the #301 relay listing, and the fuel pump fuse.
4. The inertia switch is a separate part. The fuel pump inertia switch, also called the fuel cutoff switch, is commonly located in the front passenger footwell behind the kick panel. It is designed to shut off the fuel pump after a collision or sharp impact. It is not the relay, but it can interrupt power to the pump and cause a crank-no-start condition.
3. What the Fuel Pump Relay Does
The relay is an electrical switch. It allows a low-current control circuit to turn a higher-current fuel pump circuit on and off. When the key is turned to ON, the powertrain control module energizes the pump circuit for a short prime cycle. Many drivers can hear a brief hum from the fuel tank for a few seconds.
The relay helps protect the control circuit. The pump needs steady battery voltage. The relay handles that load while the PCM controls the timing. When the relay contacts wear, stick, burn, or fail internally, the pump may not receive power.
A bad relay can look like a dead pump. A no-start, stall, no pump prime sound, or no fuel pressure can come from a fuse, relay, inertia switch, wiring issue, PCM control problem, or the pump itself. That is why the cheap and accessible checks come first.
4. Symptoms That Point to the Relay or Its Circuit
1. Engine cranks but does not start. The starter turns the engine normally, but the engine does not fire. If the pump does not prime, the fuel rail may not have enough pressure. A failed relay can cause this.
2. No brief pump hum from the tank. With the key turned to ON, many vehicles produce a short pump sound from the rear. No sound does not prove the pump is bad, but it is a useful clue. A helper can turn the key while you listen near the fuel tank.
3. Intermittent starting. A relay with worn contacts may work cold, then fail when hot. It may also work after tapping the relay or after the truck sits. Intermittent electrical faults are often harder to confirm than a fully dead part.
4. Stalling while driving. A relay that opens unexpectedly can cut power to the pump and stop the engine. Because stalling can affect power steering and braking assistance, avoid driving a vehicle that has an unresolved fuel cut-out problem.
5. Relay clicks but the pump still does not run. A click only tells you the relay coil may be moving. It does not prove the high-current contacts are passing power. Burnt contacts can still leave the pump without voltage.
6. Fuel pump fuse blows again. A repeated blown fuse suggests a short circuit, damaged wiring, or excessive current draw in the pump circuit. Do not keep installing fuses and cranking the engine. Find the cause first.
5. Fast Checks Before Replacing Any Parts
1. Confirm the basics. Make sure the battery is charged, the engine ground cables are clean and tight, and the starter cranks at normal speed. A weak battery can lead to misleading voltage readings.
2. Check the 20A fuel pump fuse. Pull the fuse and inspect it visually. A test light or multimeter gives a better answer than eyesight alone. Check for power on both sides of the fuse with the key in the correct position. If the fuse is blown, replace it only with the same amperage rating.
3. Check the PCM-related fuse. Published diagrams also list a 15A fuse connected to the PCM, injectors, fuel pump circuit, and MAF sensor. If that fuse is blown, the engine may have other control-circuit problems that affect starting.
4. Listen for the prime cycle. Turn the key from OFF to ON without cranking. Listen for a short hum from the tank. Repeating this several times can help, but do not flood the engine or crank for long periods.
5. Inspect the inertia switch. In the front passenger footwell behind the kick panel, look for the reset button. If it is popped up, follow the owner's manual procedure to reset it. A pothole, parking-lot bump, or minor impact can trip the switch.
6. Check for obvious wiring damage. Look for corroded connectors, loose terminals, melted relay sockets, brittle insulation, and signs of previous repairs. Older SUVs may have had alarm systems, remote starters, trailer wiring, or aftermarket stereo work that disturbed factory wiring.
6. How to Test the Fuel Pump Relay
1. Use the relay swap test. This is the quickest no-cost test. Find another relay in the same power distribution box with the same part number and terminal layout. Common candidates include the horn, wipers, or other standard Ford relays, but only swap relays that match exactly. If the Expedition starts after the swap, the original fuel pump relay is likely faulty.
2. Label before you swap. Take a phone photo of the box and cover before moving anything. Put relays back in their original positions after testing. Do not leave a known-bad relay in a safety-related circuit.
3. Feel and listen for relay operation. With the key turned to ON, a helper may hear or feel a click from the relay. This only confirms that the control side is trying to activate the relay. It does not confirm that power is leaving the relay to the pump.
4. Check the relay socket with a test light or multimeter. Remove the relay and inspect the terminals. With the key ON, one or more terminals should show battery voltage depending on circuit design. Published general guidance notes that battery voltage should be present at two of the four relay terminals during key-on checks, but terminal numbering and circuit behavior should be verified against a wiring diagram for the exact truck. If no power is present, look upstream at the fuse, ignition switch feed, PCM control, and wiring.
5. Inspect the relay itself. Pull the relay and look for melted plastic, burned smell, darkened terminals, corrosion, or loose pins. A relay that has been hot for a long time may also show discoloration at the socket.
6. Bench test only as a partial check. Applying battery power to the relay coil can show whether it clicks, but it does not prove the contacts can carry pump current under load. A relay can click on a bench and still fail in the truck.
7. How to Check Power Before Dropping the Fuel Tank
1. Test at the fuel pump connector when accessible. If the fuse, relay, and inertia switch check out, the next question is whether voltage reaches the pump. Published 1999 Expedition guidance describes checking for 12 volts at the pump connector during the prime cycle; voltage there indicates the supply side is working and the pump itself is suspect. No voltage points back to wiring, relay control, fuse links, or the inertia switch.
2. Use a fuel pressure gauge. A no-start diagnosis is stronger when you have an actual pressure reading. Follow the service manual procedure for the engine in your truck. Do not open fuel lines casually. Fuel spray is dangerous.
3. Avoid repeated starting-fluid use. Some Ford Triton engines with plastic intake parts can be damaged by improper starting-fluid use, and forums warn against it. Starting fluid may also hide the real problem by making the engine fire briefly without fuel pressure.
4. Work safely. Fuel vapor ignites easily. Work outdoors or in a well-ventilated area. Keep sparks, flames, cigarettes, and hot tools away. Wear eye protection. Have a Class B/C fire extinguisher nearby. Relieve fuel pressure before opening the system.
8. When to Replace the Relay
Replace the relay when the evidence points to it. The strongest signs are: the fuse is good, the socket has proper feed voltage, the inertia switch is reset, the pump does not prime, and a known-good matching relay makes the truck start or restores pump operation. A replacement relay should match the original part number, terminal layout, and current rating.
Buy the right style. Use a relay from a reputable auto parts source. Bring the old relay to the counter or compare the number printed on top. Cheap relays with poor internal contacts can cause repeat problems.
Recheck after installation. After installing the new relay, turn the key ON and listen for the pump prime. Start the engine, let it idle, then road test carefully. Recheck for relay heat, flickering, hesitation, or repeat stalling.
Do not ignore a repeated failure. If a new relay fails quickly, the pump may be drawing too much current, a circuit may be shorted, or the socket may have high resistance from heat damage. Current overload and short circuits are listed as common causes of relay failure.
9. When the Fuel Pump Is More Likely the Problem
1. Power reaches the pump but it does not run. If you confirm battery voltage and ground at the pump connector during the prime cycle and the pump stays silent, the pump is a prime suspect.
2. The pump runs but pressure is low. A worn pump can still make noise without producing correct pressure. A bad internal seal, clogged strainer, leaking regulator, or restricted filter can also affect pressure.
3. The truck loses power under load. Hesitation, sputtering at highway speed, or a engine that struggles on hills can point toward low fuel delivery. These symptoms also overlap with ignition and sensor issues, so test before replacing parts.
4. Whining from the fuel tank. A loud whine can be associated with a failing pump, although some pump noise is normal. A new noise that grows louder over time deserves attention.
5. Long crank times. A pump that cannot hold residual pressure may cause extended cranking before start. A fuel pressure gauge and a leak-down check help separate pump, check valve, injector, and regulator issues.
10. 1999 Ford Expedition Fuel Pump Replacement Basics
1. Confirm fitment. Check engine size, 2WD or 4WD, emissions configuration, VIN, and whether the truck has a factory or replaced tank assembly. Parts catalogs can split by production date and fuel system design.
2. Reduce fuel level. A full tank is heavy and increases spill risk. Siphon or transfer fuel only with an approved pump and container. Never mouth-siphon gasoline.
3. Decide on access method. On many trucks of this era, pump replacement involves lowering the fuel tank. Some owners create an access opening under the rear seat, but cutting into a vehicle floor requires care because of fuel lines, wiring, and structural parts. If you are not trained for that work, drop the tank or hire a shop.
4. Disconnect the battery. Ford guidance for power distribution box service includes battery disconnection, and disconnecting the battery can require idle relearn and resetting the clock and radio presets.
5. Support the tank. Use a jack and a wide support board. Do not let the tank hang by hoses or wiring. Disconnect filler neck, vent lines, electrical connectors, fuel lines, and straps according to the service manual.
6. Clean the tank opening. Dirt around the pump module can fall into the tank. Clean the area before removing the lock ring. Use a proper lock-ring tool instead of hammering with a screwdriver.
7. Replace related wear items. Install a new strainer, seal, and any supplied hardware. A clogged fuel filter should also be checked. Reusing a swollen old O-ring can cause a fuel smell or leak.
8. Leak-check before driving. Reconnect the battery, cycle the key a few times to prime the system, inspect all connections, then start the engine. Check for leaks before moving the vehicle.
11. Common Mistakes That Waste Money
1. Replacing the pump before checking the relay. This is the biggest one. A relay is cheap and easy to test compared with dropping a fuel tank.
2. Trusting the wrong diagram. Use 1999-specific information. Grouped 1997–2002 diagrams can include multiple box versions.
3. Installing a larger fuse. A larger fuse can allow wiring to overheat. Stick to the specified amperage.
4. Assuming a click means the relay is good. The control coil may click while the load contacts are burned.
5. Forgetting the inertia switch. A tripped cutoff switch can stop the pump even when the fuse and relay are good.
6. Ignoring security and PCM inputs. If the key is not recognized or the PCM does not command the relay, the pump may not run. General no-start guides include immobilizer and PCM control checks after basic power checks.
7. Driving with an intermittent stall. A fuel-related stall can happen at speed and reduce power steering assist. Fix the cause before using the truck for family trips, towing, or highway commuting.
12. Tools That Make the Job Easier
1. Owner's manual. Use it for box layout, fuse ratings, and safety notes.
2. Test light or digital multimeter. These are the core tools for checking voltage, ground, and fuse condition.
3. Fuel pressure gauge. Useful for confirming whether the pump circuit is creating real pressure.
4. Fuse puller and needle-nose pliers. Helpful for tight relay and fuse positions.
5. Phone camera. Take photos before removing relays or connectors.
6. Work light. The power distribution box can be hard to read in a dim garage.
7. Gloves and eye protection. Fuel and battery work both require basic protection.
8. Jack, jack stands, and a transmission jack or support board. Needed if the tank must be lowered.
13. Practical Diagnostic Order
1. Verify the complaint. Does the engine crank? Does it start briefly and die? Does it stall hot, cold, or under load? Does the pump prime?
2. Check the battery and grounds. Low voltage skews everything.
3. Inspect the 20A fuel pump fuse and the related 15A circuit fuse.
4. Locate relay #301 in the under-hood Power Distribution Box.
5. Swap with a matching known-good relay.
6. Check relay socket power and ground.
7. Reset or test the inertia switch in the passenger footwell.
8. Check for 12 volts at the pump connector during prime.
9. Measure fuel pressure. Use the service specification for your engine.
10. Only then decide whether the pump needs replacement. This order keeps the expensive job last.
14. Questions U.S. Owners Often Ask
Is the relay inside the cab?
Some online answers mention the passenger-compartment fuse panel, but 1999 model listings commonly place the fuel pump relay in the under-hood power distribution box. The inertia switch is the fuel-related part commonly found in the passenger footwell.
Can I drive with a bad relay?
It is not wise. If the relay opens while driving, the engine can stall unexpectedly. Have the truck diagnosed before highway use.
Does a bad relay always set a check-engine light?
No. A no-start condition may not give you a useful code, and older vehicles do not monitor every part of the pump circuit in the same way. A scan tool can still help with PCM codes and data, but basic electrical checks remain important.
Will disconnecting the battery reset anything?
Yes. Owner discussions note that disconnecting the battery for power distribution box service can cause the Expedition to relearn idle and may require resetting the clock and radio presets.
Can a relay be good even if the pump does not run?
Yes. The PCM command, inertia switch, fuse link, ground, connector, or wiring may be at fault. Or the pump may be dead. Testing the socket and pump connector narrows it down.
Should I replace the relay with the pump?
If the pump is being replaced because it has high mileage and the relay is original, many owners install a new relay as low-cost preventive maintenance. It does not replace proper diagnosis, but it can be reasonable on an older truck.
15. Choosing a Replacement Fuel Pump
1. Prioritize correct fit. A pump must match the tank module, connector, pressure requirement, and fuel line layout. Use your VIN and build date when ordering.
2. Look for OE-style installation. A direct-fit assembly reduces wiring changes and fitment problems. KEMSO describes its pumps as high-performance OEM replacements designed for factory-style fit.
3. Consider fuel compatibility. Many U.S. pumps encounter ethanol-blended gasoline. Published KEMSO product information describes gasoline and E85/ethanol compatibility on several pump lines. Always confirm the exact listing for your vehicle before purchase.
4. Check warranty terms. A lifetime warranty is a meaningful benefit for a part that requires tank access. KEMSO product pages and KEMSO articles state that their fuel pumps come with a lifetime warranty, including serialized pump bodies on some listings.
5. Replace the strainer and seal. A new pump with an old clogged strainer or damaged seal can lead to a repeat repair.
6. Buy from a source that supports fitment questions. U.S.-based technical support is listed on multiple KEMSO pump listings. That matters when working on a 25-plus-year-old SUV with possible production changes.
16. Recommended Fuel Pump Brand: KEMSO
If testing confirms that your 1999 Ford Expedition needs a fuel pump, we recommend buying a KEMSO Fuel Pump. KEMSO fuel pumps are presented as high-performance, OEM Replacement parts designed to meet or exceed factory fit, flow, and pressure requirements. KEMSO also states that its pumps come with a lifetime warranty. For an older Expedition, a direct-fit pump with a clear warranty is a practical choice because fuel pump replacement involves significant labor and tank access.
KEMSO product information also highlights high-flow options and gasoline/E85 compatibility across parts of its lineup. Always choose the exact part listed for your year, engine, and fuel system rather than buying based only on flow rating. If your truck is stock, OEM-style replacement fit matters more than an upgrade built for a modified engine.
Visit the official KEMSO website here: https://www.kemsoracing.com/ You can review the fuel pump catalog, check fitment details, and find the right replacement for your vehicle.
17. Final Checklist
1. The 1999 Ford Expedition fuel pump relay is in the under-hood Power Distribution Box, commonly listed as relay #301.
2. The fuel pump fuse is in the same box, commonly listed as a 20A mini fuse at position #10.
3. Check the inertia switch in the passenger footwell before condemning the pump.
4. Swap only with a relay that has the same part number and terminal layout.
5. Use a multimeter, test light, and fuel pressure gauge instead of guessing.
6. Do not install a higher-amp fuse.
7. Confirm voltage at the pump connector before dropping the tank.
8. If the pump is bad, choose a direct-fit replacement with a solid warranty.
9. Take fuel safety seriously. Work in a ventilated area, keep ignition sources away, and check for leaks before driving.
10. Keep the owner's manual in the glovebox. On an older SUV, that small book can prevent a wrong-part purchase.
A 1999 Expedition is old enough that heat, corrosion, previous repairs, and worn connectors are part of normal ownership. The good news is that the first checks are simple. Open the hood, find the power distribution box, verify the 20A fuse and #301 relay, reset the inertia switch if needed, and test for voltage before paying for a pump. That straightforward order is the difference between a quick roadside fix and an unnecessary tank-out job.
For replacement pumps, warranty coverage and exact fitment should be high on the list. KEMSO offers high-performance, OEM-replacement fuel pumps with lifetime warranty coverage as stated in its product information. Review the catalog and confirm your application at the official site below.