99 Ford Expedition Fuel Pump Relay: Location, Symptoms, and Fixes

If your 1999 Ford Expedition cranks but will not start, stalls while driving, or has no fuel pump prime sound when you turn the key, check the fuel pump relay, fuel pump fuse, inertia shut-off switch, and fuel pump circuit before buying a fuel pump. On this SUV, the fuel pump relay and fuel pump fuse are in the under-hood Power Distribution Box, while the fuel pump itself is inside the fuel tank . The fast diagnosis is simple: verify the 20-amp fuel pump fuse in position #10, identify relay #301, listen for the pump’s brief prime, swap the relay with an identical known-good relay, then check the inertia switch and power at the fuel pump connector . If the fuse, relay, switch, and wiring check out but the pump stays silent with battery voltage present, the fuel pump needs replacement .

This guide is written for U.S. owners of the 1999 Ford Expedition, including the 4.6L and 5.4L V8 models commonly used for family transport, towing, and daily driving. The steps below start with the cheapest and easiest checks, then move toward tests that require more time and tools. Always verify the diagram on your fuse box cover or in the owner’s manual before removing parts, because production changes, previous repairs, and aftermarket accessories can affect labeling .

1. What the 99 Ford Expedition Fuel Pump Relay Does

The fuel pump relay is an electrical switch that lets a low-current control circuit turn on a higher-current circuit for the fuel pump. When you turn the ignition key to ON, the powertrain control system energizes the relay for a short prime cycle, the relay contacts close, and the in-tank pump builds pressure for starting . On many Ford trucks and SUVs of this era, the pump runs briefly at key-on, then runs continuously once the engine starts .

A relay can fail in several ways:

  1. The coil stops working. The relay will not click, and the contacts never close .
  2. The contacts burn or stick. You may hear a click but get no power to the pump, or the pump may behave intermittently .
  3. Heat and age cause intermittent failure. The SUV may stall when hot, then restart after cooling down .
  4. Circuit overload damages the relay. A failing pump or a short circuit can pull too much current and overheat the contacts .

A bad relay can look exactly like a dead pump, a bad ignition switch, or a fuel delivery problem. That is why the relay and fuse should be checked first. A simple swap test can prevent an unnecessary fuel pump replacement .

2. Where the Fuel Pump Relay Is on a 1999 Ford Expedition

The 1999 Expedition has more than one fuse area, but the fuel pump components are in the Power Distribution Box under the hood .

Under-Hood Power Distribution Box

Open the hood and look for the black plastic fuse and relay box in the engine compartment. Published guides place it on the driver’s side near the battery, and other guides describe the under-hood Battery Junction Box near the brake master cylinder area . Because descriptions of exact side placement vary, use the fuse box cover diagram and your owner’s manual as the final reference for your specific truck .

Inside this box, look for:

  1. Fuse #10: a 20-amp mini fuse for the fuel pump .
  2. Fuse #18: a 15-amp fuse listed for the Powertrain Control Module, fuel injectors, fuel pump, and mass air flow sensor .
  3. Relay #301: the fuel pump relay, described as a full-size relay in the same box .
  4. Other standard relays: horn, A/C clutch, headlamp, or PCM-related relays may share the same shape and part number, depending on the box layout .

The cover usually has a map. If the printed diagram is faded or missing, take a clear photo before pulling anything, then compare the numbers molded into the plastic with the owner’s manual . Guessing at relay positions can waste time and can lead to swapping a relay that controls another system.

Passenger Compartment Fuse Panel

The cabin fuse panel is below and to the left of the steering wheel near the brake pedal . It handles items such as interior lamps, audio, wipers, cluster, and other body circuits . It does not contain the main fuel pump fuse or fuel pump relay for this model . Owners often waste time under the dash because many later vehicles hide relays there. On a 1999 Expedition, start under the hood.

Fuel Pump Inertia Shut-Off Switch

The inertia switch, also called the fuel cutoff or shut-off switch, is a safety device that cuts power to the fuel pump after a collision or hard jolt . Most 1999 Expedition guides place it in the right front passenger footwell behind the kick panel, with a reset button on top . Some online answers give different locations for related Ford models, so check your owner’s manual and inspect the passenger footwell area before assuming the switch is missing .

If the button has popped up, inspect for fuel leaks and fuel smell first. If there is no sign of a leak, press the reset button down and try starting the vehicle again . This switch is not the relay, but it can stop the pump in the same way.

3. Common Symptoms of a Bad 99 Ford Expedition Fuel Pump Relay

A failing relay usually affects whether the pump receives power. Watch for these signs.

1. Engine Cranks But Will Not Start

The starter turns the engine normally, but the engine does not fire. When the key is turned to ON, you should hear a short hum or whir from the rear of the vehicle as the pump primes . If there is no prime sound, the relay, fuse, switch, wiring, or pump may be involved .

A quick clue is whether the engine briefly runs on starting fluid and then dies. That points toward a fuel delivery problem, but it does not prove the pump is bad. It only tells you to test the fuel system properly .

2. No Click From the Relay

With a finger on the relay and a helper turning the key to ON, a working relay usually gives a light click . No click may mean the relay coil is bad, the control side is not getting power, or the fuse and related circuit need checking .

3. Click, But No Pump Sound

If the relay clicks but the pump does not hum, the relay contacts may be burned, the fuse may be open, the inertia switch may be tripped, or power may be lost downstream .

4. Intermittent Stalling

An aging relay can work cold and fail hot. The engine may die in traffic, then restart after the vehicle sits . This symptom is easy to misdiagnose as an ignition problem. If the stall happens with no warning light, no fuel pump prime sound, and no pump hum, test the relay circuit early.

5. Long Cranking Before Starting

A weak relay or low fuel pressure can cause extended cranking before the engine fires . Do not keep cranking for long periods. Repeated long cranking can overheat the starter and drain the battery.

6. Loss of Power Under Load

Sputtering, hesitation, or power loss at highway speed can come from low fuel pressure, a restricted filter, a weak pump, wiring voltage drop, or a relay that cannot carry current consistently . A relay problem is often intermittent; a worn pump often gets worse over time .

7. Whining Noise From the Fuel Tank

A loud whine from the tank area is commonly listed as a fuel pump warning sign . A normal pump makes a brief low hum at key-on. A loud, changing, or persistent whine deserves inspection before the pump leaves you stranded.

4. Tools and Parts That Make the Job Easier

You do not need a full professional shop for the first checks. These items cover most driveway diagnosis:

  1. Owner’s manual for the exact fuse and relay diagram .
  2. Fuse puller or needle-nose pliers to remove mini fuses .
  3. Replacement 20-amp mini fuse with the same rating .
  4. Test light or digital multimeter for voltage checks .
  5. Fuel pressure gauge with the correct adapter for the Schrader valve on the fuel rail .
  6. Basic hand tools for trim panels, battery terminal, and fuse box access .
  7. Safety glasses, gloves, a rag, and a fire extinguisher for any fuel system work .

Do not install a higher-amp fuse to “get home.” The fuse rating protects the wiring. A higher rating can allow the harness to overheat and create a fire risk .

5. Safety Before You Touch the Fuel System

Fuel vapor is flammable, and the pump circuit is live during key-on testing. Use these rules every time:

  1. Work outdoors or in a well-ventilated area .
  2. Keep sparks, flames, cigarettes, and incandescent drop lights away from the work area .
  3. Turn the ignition off and remove the key before pulling fuses or relays .
  4. Disconnect the negative battery cable when working on wiring, the fuel tank, or the pump connector . Ford guidance for servicing the Power Distribution Box includes battery disconnection; expect the idle relearn, clock, and radio presets to need resetting afterward .
  5. Relieve fuel pressure before opening fuel lines. One common method is removing the fuel pump fuse and running the engine until it stalls, then disconnecting the battery . Follow the service manual for your exact engine.
  6. Cover the Schrader valve with a rag when checking or relieving pressure, and protect your eyes .
  7. Stop immediately if you smell raw gasoline or see a leak. Fix the leak before doing any electrical testing .
  8. Support the vehicle correctly if you work underneath it. Never rely on a jack alone when lowering a tank .

If the vehicle has been in a collision, inspect the fuel lines, tank, and wiring before resetting the inertia switch .

6. Step-by-Step Diagnosis: Start Simple

Use this order. It moves from the most common low-cost items to the more involved checks.

Step 1: Confirm the Complaint

  1. Turn the key to ON without cranking.
  2. Listen near the rear seat or rear wheel well for a 1–3 second pump hum .
  3. Watch the dashboard and note whether the Check Engine light comes on with key-on.
  4. Try a short start attempt, but do not grind the starter.
  5. Write down whether the problem is cold, hot, after rain, after a bump, or after refueling.

That short observation helps separate an intermittent relay from a weak pump, tripped inertia switch, or wiring fault .

Step 2: Check Fuse #10

  1. Switch the ignition off and remove the key .
  2. Open the under-hood Power Distribution Box.
  3. Find fuse #10, the 20-amp mini fuel pump fuse .
  4. Pull it straight out with a fuse puller.
  5. Inspect the metal strip. A broken, melted, or discolored strip means the fuse is blown .
  6. Replace it only with a 20-amp mini fuse .

Also inspect fuse #18, the 15-amp circuit listed for the PCM, injectors, fuel pump, and MAF sensor . A problem there can affect engine management as well as fuel delivery.

If a new fuse blows as soon as the key is turned on, stop. Repeatedly installing fuses can damage wiring or components . Look for a short in the pump harness, damaged insulation near the tank and frame, a failing pump drawing too much current, or a relay fault .

Step 3: Find and Inspect Relay #301

The fuel pump relay is listed as #301 in the Power Distribution Box . It is a full-size relay . Some guides also refer to position R1 or a “Fuel Pump” label on the cover, so confirm with the diagram rather than relying only on a generic position .

  1. Remove the cover and compare the layout with the label.
  2. Photograph the relay positions.
  3. Pull the suspected relay straight up.
  4. Check for melted plastic, corrosion, loose terminals, water stains, or burnt odor.
  5. Read the part number and pin layout printed on top .
  6. Install a replacement with the same part number and pin configuration .

Water intrusion and corrosion are known electrical problems on this generation of Ford trucks and SUVs, especially around interior fuse areas and the GEM module on affected vehicles . If you see green corrosion or moisture inside a box, clean and dry the area correctly before installing new parts, or have a shop inspect it.

Step 4: Do the Relay Swap Test

This is the fastest no-cost test.

  1. Find another relay in the same box with the identical part number and pin layout. Common candidates include the horn or A/C clutch relay, but only use a relay that matches .
  2. Swap the suspected fuel pump relay with the known-good relay.
  3. Turn the key to ON and listen for the pump prime.
  4. Try starting the engine.
  5. Check the system you borrowed from. If the horn stops working after the swap and the engine now starts, the original relay is bad .
  6. Replace the faulty relay with the correct part. Do not leave a safety or lighting circuit disabled.

Many auto parts stores stock this style of relay, often for a modest price, and replacement usually takes minutes . Bring the old relay to the counter to compare terminals and markings .

Step 5: Listen and Feel for the Click

Place a finger on the relay while a helper turns the key to ON .

  1. Click and pump hum: the basic relay and pump prime circuit are working. Move to fuel pressure if the engine still runs poorly.
  2. No click: check fuse #10, fuse #18, PCM power, ignition switch feed, and the relay control circuit .
  3. Click but no hum: suspect burned relay contacts, a tripped inertia switch, an open fuse, wiring between the box and tank, or a dead pump .

Step 6: Reset the Inertia Switch

If the vehicle recently hit a pothole, curb, or another vehicle, check the shut-off switch in the passenger footwell behind the kick panel .

  1. Turn the ignition off.
  2. Look for the switch and its red reset button .
  3. Inspect for fuel odor or visible leaks.
  4. If the button is up and there is no leak, press it down .
  5. Turn the key to ON and listen for the pump.

If the switch trips again without an impact, have the switch and its circuit inspected .

Step 7: Check Voltage at the Relay Socket

Use a test light or multimeter set to DC volts.

  1. Remove the relay.
  2. Have a helper turn the key to ON.
  3. Check for battery voltage at the relay socket feed terminals. Published DIY guidance notes that a healthy socket should show battery voltage on two terminals during key-on testing .
  4. If there is no voltage, check the fuses, ignition feed, PCM-related fuse, and wiring .
  5. If voltage is present but the pump does not run, continue downstream.

Do not probe terminals with a meter lead that bridges adjacent pins. Use a wiring diagram and a careful test method to avoid a short.

Step 8: Check Fuel Pressure at the Rail

The 4.6L and 5.4L Triton engines commonly have a Schrader-type test port on the fuel rail . A fuel pressure gauge gives a direct reading instead of relying on sound alone .

  1. Relieve pressure safely and protect your eyes .
  2. Connect the correct gauge to the rail test port .
  3. Cycle the key to ON and observe the prime pressure.
  4. Compare the reading with the specification in a factory service manual or a repair database for your exact engine and VIN.
  5. Watch whether pressure holds after key-off and whether it drops under load.

Some aftermarket listings for 1999–2002 Expedition 4WD pumps state 44 PSI, but that is a parts listing, not a factory diagnostic specification . For an accurate repair decision, use the specification for your engine, emissions package, and fuel system rather than a universal number from a product page .

Low pressure can come from a weak pump, restricted filter, faulty pressure regulator, blocked line, or voltage loss . A relay that closes but delivers poor voltage due to corroded contacts can also starve the pump.

Step 9: Check Power at the Fuel Pump Connector

The pump sits inside the tank . On some vehicles, the connector can be reached from underneath near the tank; some guides mention an access panel under the rear seat, while others describe dropping the tank for pump replacement . Verify the access route on your vehicle before removing interior trim or tank straps.

  1. Disconnect the battery before unplugging the pump connector .
  2. Set the multimeter to DC voltage.
  3. Reconnect the battery for the test only when everything is secure.
  4. Have a helper turn the key to ON.
  5. Look for roughly battery voltage during the 1–2 second prime cycle .
  6. Voltage present, pump silent: the pump is the likely failure .
  7. No voltage: the fault is upstream in the fuse, relay, inertia switch, wiring, or control side .

Also inspect the ground side. A bad ground can make a good pump and relay look faulty .

7. How to Replace the Fuel Pump Relay

Once the swap test confirms the relay is bad:

  1. Buy the correct relay. Match the part number, terminal count, pin layout, and current rating . A standard 4-pin or 5-pin relay is commonly used, but verify the old part instead of assuming .
  2. Turn the key off. Remove the key.
  3. Disconnect the negative battery cable if you will be working inside the Power Distribution Box beyond a simple relay pull .
  4. Pull the old relay straight out. Do not twist hard enough to damage the socket.
  5. Inspect the socket. Look for corrosion, pushed-out terminals, melted plastic, or water.
  6. Push the new relay in firmly. It should seat fully.
  7. Reinstall the cover. Make sure the cover seals correctly to keep water out .
  8. Reconnect the battery.
  9. Cycle the key. Listen for the prime hum.
  10. Start the engine and check for stalls, hesitation, or abnormal noise.
  11. Reset radio presets, clock, and idle relearn if battery disconnection cleared them .

A new relay that fails quickly is a warning sign. A pump drawing excessive current, a shorted harness, or corrosion in the box can damage the replacement . Find the cause before installing another one.

8. If the Relay Is Good, Check These Parts Next

1. Fuel Pump Fuse and PCM Circuit Fuse

Fuse #10 protects the fuel pump feed. Fuse #18 is listed for the PCM, injectors, fuel pump, and MAF sensor . A blown fuse can be caused by damaged wiring, a short, or a pump drawing too much current . Never bypass a fuse.

2. Inertia Shut-Off Switch

A tripped switch removes power from the pump after an impact or hard jolt . It is a common no-start check on older Ford vehicles.

3. Wiring Harness

Inspect the harness from the under-hood box toward the rear of the vehicle, especially near the frame, tank, and any area where the loom can rub . Look for:

  1. Chafed insulation.
  2. Green corrosion at connectors.
  3. Loose terminals.
  4. Previous splice repairs.
  5. Damaged trailer wiring or aftermarket alarm wiring.
  6. Pinched harness near the tank after a pump or tank service.

4. Fuel Filter

A severely restricted filter makes the pump work harder and can reduce fuel flow . On an older SUV with unknown service history, a restricted filter is worth checking as part of the fuel delivery diagnosis. Replace it with the correct part for the year and engine.

5. Fuel Pressure Regulator and Lines

A faulty regulator or a restricted line can cause pressure and driveability problems . Use a gauge and the factory specification before condemning the pump.

6. Fuel Pump Driver Module

Some later Ford systems use a Fuel Pump Driver Module, and one aftermarket guide discusses FPDM faults on 1999–2004 Expedition and Navigator applications . Because model-year and system descriptions vary in online guides, confirm whether your specific 1999 Expedition has this module and where it is mounted before ordering one . Do not replace a module based only on a generic year-range article.

7. PCM and Ignition Feed

The PCM controls the relay’s prime command . If there is no relay control, check PCM power, grounds, fuse #18, ignition switch feed, and related wiring before replacing the PCM .

8. The Fuel Pump

The 1999 Expedition pump is inside the fuel tank and is part of a module assembly that often includes the sending unit and strainer . Replacement usually means lowering the fuel tank, disconnecting lines and connectors, removing the locking ring, and installing a complete module . Some guides mention an access panel, so check your vehicle before choosing the labor path .

If voltage reaches the pump connector during the prime cycle and the pump does not run, the pump is the likely fault . If the pump runs but pressure is low, check the filter, regulator, line, strainer, and pump output before deciding .

9. How to Tell Relay Trouble From a Dead Fuel Pump

Use this practical comparison:

More likely a relay or upstream electrical issue when:

  1. The pump is silent, but swapping in an identical relay restores the prime .
  2. The relay does not click at key-on .
  3. The problem changes with heat and returns after cooling .
  4. Fuse #10 is blown or the relay socket shows no feed voltage .
  5. The inertia switch reset button is up after a bump .
  6. Wiring near the tank or frame is damaged .

More likely the pump when:

  1. Fuse, relay, inertia switch, and wiring test good .
  2. Battery voltage reaches the pump connector during prime, but the pump stays silent .
  3. A fuel pressure gauge shows low pressure against the correct factory specification .
  4. The tank-area whine grows louder over time .
  5. The engine loses power under load or sputters at speed and the electrical supply is stable .
  6. The fuse blows repeatedly because the aging pump draws too much current .

Do not use sound alone as the final verdict. A pump can hum and still deliver low pressure . A relay can click and still fail to carry current .

10. Realistic Cost and Time Expectations for U.S. Owners

Prices vary by region, brand, and whether you buy at a local parts store or online.

  1. Fuse: usually a low-cost item, often sold in a small pack. Always match the 20-amp rating .
  2. Relay: commonly described as an inexpensive part, with many replacements available for under $20 .
  3. Fuel filter: moderate cost; service history matters on an older SUV .
  4. Fuel pump module: higher part cost than a relay or fuse, plus significant labor because the tank may need to be lowered .
  5. Professional diagnosis: useful when a fuse keeps blowing, voltage is missing at the connector, or an intermittent fault cannot be repeated at home .

Call two or three local shops and ask for the diagnostic fee, hourly labor rate, and whether they pressure-test before replacing the pump. A shop that checks the relay, fuse, pressure, and pump current draw is more likely to find the real cause than one that replaces parts based only on a no-start symptom .

11. Buying the Right Relay and Pump for a 1999 Expedition

Before ordering parts, have this information ready:

  1. Model year: 1999.
  2. Engine size: 4.6L V8 or 5.4L V8 .
  3. Drive type: 2WD or 4WD, because some pump listings are 4WD-specific .
  4. VIN and production date.
  5. Emissions package and fuel system details.
  6. Old part number from the relay or pump assembly.
  7. Whether the vehicle has an access panel or requires tank removal .
  8. Towing or performance use, if the vehicle is modified.

For the relay, match the number printed on top and the terminal layout . For the pump, use a complete module that fits the tank, sending unit, fuel lines, and electrical connector . Some 1999–2002 4WD applications list OE numbers such as XL1Z-9H307AA or XL1Z-9H307AB, but verify fitment by VIN rather than copying a number from a generic listing .

Ask the seller:

  1. Is this a complete module or pump only?
  2. Does it include the strainer, sending unit, seal, and lock ring where applicable?
  3. What is the warranty?
  4. Is it intended as a direct OEM replacement?
  5. What is the return policy if the VIN shows a different tank or sender?
  6. Are the electrical connector and fuel line fittings the same as the original?

12. Fuel Pump Replacement: What the Job Usually Involves

This is a bigger job than a relay swap. A typical service procedure includes the following :

  1. Run the fuel level low to reduce tank weight.
  2. Relieve fuel system pressure using the service manual procedure .
  3. Disconnect the negative battery cable .
  4. Support the vehicle safely with jack stands if working underneath .
  5. Disconnect fuel lines and electrical connectors from the tank .
  6. Support the tank with a floor jack and remove the retaining straps .
  7. Lower the tank carefully, watching for hoses and wires that still connect .
  8. Clean the tank opening before removing the locking ring so dirt does not fall inside .
  9. Remove the locking ring and lift out the module, taking care not to bend the float arm .
  10. Compare the new module to the old one before installation .
  11. Install a new seal and seat the module correctly .
  12. Reinstall the tank, lines, straps, and connector.
  13. Reconnect the battery and prime the system by cycling the key several times.
  14. Check for leaks before starting, then again after the engine runs .
  15. Verify fuel pressure and road-test the vehicle .

If you smell fuel, see a leak, or find damaged wiring, stop and get professional help . Working under a suspended tank with fuel inside is not a job to rush .

13. Mistakes That Lead to Repeat No-Start Problems

  1. Replacing the pump before checking the relay. A low-cost relay can create the same no-start symptom .
  2. Using a higher-amp fuse. This removes circuit protection and creates a fire risk .
  3. Ignoring the inertia switch. A hard bump can trip it .
  4. Swapping a non-identical relay. Match part number and pin layout .
  5. Skipping fuel pressure measurement. Sound does not confirm correct pressure .
  6. Leaving a corroded socket untreated. Corrosion and water intrusion can cause repeat electrical faults .
  7. Forgetting the ground circuit. A poor ground can stop a good pump .
  8. Buying the wrong pump for 2WD, 4WD, engine, or sending unit .
  9. Running the tank near empty on a regular basis. Fuel cools and lubricates an in-tank pump, and running dry can overheat it .
  10. Ignoring a repeatedly blown fuse. A short or overloaded pump must be found first .

14. Maintenance Habits That Help an Older Expedition

A 1999 vehicle is old enough that prevention matters as much as repair.

  1. Keep at least a quarter tank of fuel when possible, especially in hot weather, to help the in-tank pump stay cool .
  2. Replace the fuel filter on schedule or sooner if service history is unknown .
  3. Listen for changes in pump noise during the key-on prime .
  4. Fix windshield and cowl leaks quickly. Water intrusion is a known electrical problem on this generation of Ford trucks and SUVs .
  5. Keep the Power Distribution Box cover sealed after every service .
  6. Inspect the tank harness during oil changes if the vehicle sees rough roads, towing, or winter road salt .
  7. Use quality fuel from busy stations and address contamination or water in the tank promptly .
  8. Do not ignore long cranking. Early testing is cheaper than a tow .
  9. Keep a spare correct-amp fuse and a known-good relay in the glovebox for roadside diagnosis, along with the owner’s manual .
  10. Record every repair. A dated note about a relay, fuse, filter, or pump helps the next technician avoid duplicate work.

15. When to Call a Professional

DIY checks are fine for fuses, relays, and visual inspections, but get qualified help when:

  1. The fuel pump fuse blows repeatedly after replacement .
  2. You smell fuel or see a leak .
  3. The tank must be lowered and you lack safe lifting equipment .
  4. Voltage is missing at the pump connector but the fuse and relay test good, which may require tracing the harness .
  5. The problem is intermittent and changes with temperature or vibration .
  6. The fuse box shows water damage or heavy corrosion .
  7. The vehicle has aftermarket alarms, remote start, trailer wiring, or performance modifications that affect the fuel pump circuit.
  8. Fuel pressure does not match the factory specification and you do not have the correct gauge or adapter .
  9. The Check Engine light points to multiple circuit faults that need a scan tool and wiring diagram.
  10. You are not comfortable working around fuel vapor and a suspended tank .

A clear repair order helps the shop: “1999 Expedition, cranks no start, no pump prime, fuse #10 good, relay swap did not change the condition, please test pressure and pump connector voltage before replacing parts.” That saves diagnostic time and keeps the repair focused.

16. Frequently Asked Questions

1. Where is the fuel pump relay on a 1999 Ford Expedition?

It is in the under-hood Power Distribution Box, listed as relay #301 in 1999-specific fuse and relay references . The under-hood box is the main fuel pump fuse and relay location; the cabin fuse panel near the brake pedal is not the place to start .

2. What fuse controls the fuel pump?

Fuse #10, a 20-amp mini fuse, is listed for the fuel pump in the 1999 engine compartment diagram . Fuse #18, a 15-amp fuse, is also listed for the PCM, injectors, fuel pump, and MAF sensor .

3. Can I swap the fuel pump relay with the horn relay?

Only if the two relays have the same part number, pin layout, and rating . Check the markings on top before swapping. The horn circuit is often used as a known-good donor in DIY testing, but matching the part is the rule .

4. Will a bad relay cause stalling while driving?

Yes. An internally failing or heat-sensitive relay can cut power to the pump and cause intermittent stalling, sometimes returning after the vehicle cools .

5. How long should the fuel pump run at key-on?

Published DIY guides describe a brief prime of roughly 1–3 seconds when the key is turned to ON . If you hear no hum at all, test the fuse, relay, inertia switch, and connector voltage.

6. Does the 1999 Expedition have an inertia switch?

Most guides for this model place a fuel pump inertia shut-off switch in the right front passenger footwell behind the kick panel, with a reset button . Some online sources describe other Ford locations or later systems, so confirm with the owner’s manual for your VIN .

7. Can I drive with a bad fuel pump relay?

No. If the relay fails, the engine can stall without warning and may not restart. Replace the relay or have the vehicle towed. Do not bypass the relay with a jumper except as a controlled diagnostic test by someone who understands the circuit and fire risk .

8. How do I know the pump is bad instead of the relay?

If fuse #10 is good, relay #301 clicks or passes a swap test, the inertia switch is reset, and battery voltage reaches the pump connector during prime but the pump does not run, the pump is the likely failure . A fuel pressure gauge adds stronger confirmation .

9. Is the fuel pump inside the tank?

Yes. The 1999 Expedition fuel pump is inside the fuel tank, commonly replaced as a module with the sending unit and strainer . Tank removal is often required, though some guides mention an access panel; verify on your vehicle .

10. Why does my new fuse keep blowing?

Likely causes include a short in the pump wiring, damaged insulation touching the body, a failing pump drawing excessive current, or a related circuit fault . Do not continue installing fuses. Find the short or overload first.

11. What should a replacement relay cost?

Many standard relays are sold for under $20, though pricing depends on brand and store . Bring the old relay to match it.

12. Should I replace the relay when I replace the pump?

It is a sensible, low-cost precaution on an older vehicle, especially if the pump failure caused high current draw or the relay contacts look burnt . Inspect the socket and fuse at the same time.

13. Can low fuel damage the pump?

Fuel helps cool and lubricate an in-tank pump. Running the tank dry can cause heat stress and make the pump draw air . Keep some fuel in the tank during hot weather and before long trips.

14. Is a fuel pressure gauge necessary?

For a no-start, the relay swap and voltage checks come first. For hesitation, low power, or a pump that hums but performs poorly, a gauge is the right tool because sound does not prove correct pressure .

15. What information should I give a parts store?

Give the year, engine, 2WD or 4WD, VIN, production date, old part number, and whether you need a relay, fuse, filter, or complete pump module .

17. Recommended Fuel Pump: KEMSO

When testing shows the fuel pump itself has failed, choose a replacement that fits correctly and provides dependable pressure for a stock 1999 Expedition. We recommend KEMSO brand Fuel Pumps. KEMSO Fuel Pump products are high-performance, OEM Replacement units designed as direct-fit replacements that meet or exceed factory specifications, and they are backed by a lifetime warranty . That combination matters on an older SUV: correct fitment reduces installation problems, consistent flow supports normal starting and acceleration, and warranty coverage gives U.S. owners long-term protection after the tank has been serviced .

Before ordering, confirm your engine, drive type, VIN, connector, and module style so the replacement matches your Expedition . For product selection and fitment information, visit https://www.kemsoracing.com/ .

18. Final Checklist Before You Put the Hood Down

  1. Fuse #10 is a correct 20-amp mini fuse and is not blown .
  2. Fuse #18 has been inspected .
  3. Relay #301 matches the original part number and is fully seated .
  4. The Power Distribution Box cover is dry, clean, and closed .
  5. The inertia switch is reset if it was tripped .
  6. The pump primes for a short cycle at key-on .
  7. The engine starts without extended cranking.
  8. Fuel pressure matches the factory specification for your exact engine .
  9. There is no fuel smell or leak around the tank and lines .
  10. The vehicle completes a road test without stalling, hesitation, or loss of power under load .

For most 99 Ford Expedition fuel pump relay problems, the answer is not a new tank or a major repair. Start with the under-hood box, check fuse #10, test relay #301, reset the inertia switch if needed, and confirm voltage and pressure before buying a pump. That order saves money and gets the diagnosis right the first time .

For a high-performance OEM replacement fuel pump backed by a lifetime warranty, visit https://www.kemsoracing.com/.