99 Ford Explorer Fuel Pump Relay Location
On a 1999 Ford Explorer, the fuel pump relay is in the Power Distribution Box, also called the Battery Junction Box, under the hood on the driver side of the engine compartment. It is relay R5, and the related 20-amp mini fuse is F9, labeled “Fuel Pump Relay and RAP Module” in the 1999 Ford Explorer Owner Guide. The fuel pump shut-off switch, often called the inertia switch, is a separate safety part in the front passenger footwell behind the kick panel, not under the hood. If your Explorer cranks but will not start, stalls, or has no pump hum when you turn the key on, check the fuse, the relay, and the inertia switch before paying to drop the fuel tank and replace the pump.
This guide is written for U.S.-market 1999 Ford Explorer models, including common 4.0L V6 and 5.0L V8 versions. Fuse and relay labels can vary slightly with production date, trim, and prior repairs. Use the diagram printed on the Power Distribution Box cover, the Owner Guide, or a Ford service manual for the final word on your exact vehicle.
1. The Exact Location Under the Hood
1. Open the hood and stand on the driver side.
The Power Distribution Box sits in the engine compartment on the driver side. It is a black plastic box with a removable lid. On many Explorers it is near the battery and fender area, close to the brake master cylinder side of the engine bay. The box may have a printed fuse and relay chart on the underside of the cover.
2. Release the cover tabs.
Do not force the lid. Press the locking tabs and lift the cover straight up. Dirt, leaves, and road salt often collect around this area. Wipe the top before opening so debris does not fall into the box.
3. Identify the mini fuses and relays.
The 1999 Explorer Power Distribution Box contains several large maxi fuses, smaller mini fuses, diodes, and relays. The fuel pump circuit uses:
- F9: 20A mini fuse, “Fuel Pump Relay and RAP Module”
- R5: Fuel pump relay
The Owner Guide power distribution chart is commonly shown around page 185–186 in online copies of the 1999 Ford Explorer manual.
4. Do not confuse this box with the interior fuse panel.
The cabin fuse panel is below and to the left of the steering wheel, near the brake pedal, on this generation of Explorer. It handles items such as radio, interior lamps, wipers, power outlets, and other cabin circuits. The fuel pump relay and its 20A fuse are in the under-hood Power Distribution Box, not the dashboard fuse panel.
2. Why the Relay Matters
The fuel pump relay is an electromagnetic switch. It allows a low-current control signal from the Powertrain Control Module to turn on a higher-current circuit for the electric fuel pump. Ford uses this design so the PCM does not carry the pump’s full electrical load through its internal electronics.
When you turn the ignition key to ON, the PCM normally energizes the fuel pump relay for a short prime cycle. That is why many owners hear a brief hum from the fuel tank for a second or two before starting. After the engine starts, the PCM keeps the pump powered through the relay circuit. If the relay contacts are burned, the coil is weak, the socket is corroded, or the control side does not receive power, the pump may not run even though the pump itself is still good.
The circuit also includes the 20A fuse and the inertia switch. The inertia switch is designed to cut fuel pump power after a collision or strong impact. A hard pothole, minor bump, or loose cargo strike near the passenger footwell can sometimes trip it. Resetting it costs nothing, so it belongs early in the diagnostic order.
3. Fast Checks Before Buying a Fuel Pump
Work in this order. These checks are simple, inexpensive, and can prevent an unnecessary pump replacement.
1. Confirm there is fuel in the tank.
The fuel gauge on an older SUV can stick or read inaccurately. If the vehicle has been parked, was bought used, or the gauge behaves oddly, add a few gallons from a clean gas can. Do not rely only on the needle.
2. Listen for the pump prime.
Turn the key to ON without cranking. Have a helper listen near the fuel filler or rear of the vehicle. A short hum for about one to three seconds is normal on many Ford vehicles. No sound does not prove the pump is bad, because a blown fuse, relay fault, wiring issue, or tripped inertia switch can produce the same result.
3. Check F9, the 20A mini fuse.
Pull the fuse and look at the metal strip inside. A blown fuse will have a broken or darkened link. Use a test light or multimeter for a more reliable check. Replace it only with the same amperage rating. Never install a higher-amp fuse to “get home,” because wiring can overheat.
If a new F9 blows again, there may be a short, damaged wiring, or a pump drawing too much current. A clogged fuel filter can also make the pump work harder than normal.
4. Swap or test R5.
Many parts stores sell a replacement relay that matches the Ford-style relay used in this box. A common quick test is to swap the fuel pump relay with another relay in the same box that has the same part number and terminal layout, such as a horn or A/C relay, then try starting the engine. Only do this when the relay numbers and shapes match exactly. Do not force a relay into a socket that does not match.
A clicking relay does not guarantee the contacts are passing current. A relay can click and still have burned internal contacts. Voltage testing at the relay socket or a known-good relay swap gives better information.
5. Reset the inertia switch.
Find the switch in the front passenger footwell behind the kick panel. It is usually a small black module with a reset button on top. Press the button firmly. If it was tripped, you may feel it click back into place. Turn the key to ON and listen for the pump again.
If your SUV was in a crash, do not simply reset the switch and drive away. Inspect for fuel leaks, damaged lines, and other collision damage first.
6. Check for battery voltage and clean connections.
A weak battery can crank the engine slowly and still cause confusing no-start symptoms. Make sure battery terminals are clean and tight. Check the ground straps and the main connections at the Power Distribution Box. Corrosion or a loose connection can interrupt pump power.
7. Measure fuel pressure.
A fuel pressure gauge gives much better information than sound alone. Many U.S. auto parts stores rent or loan pressure gauges with a refundable deposit. On the 4.0L V6, a Schrader valve on the fuel rail is commonly used for testing. Published fuel pressure information for the 1999 4.0L Explorer lists approximately 57–73 PSI. Always verify the specification for your engine and VIN in a Ford service manual or a professional repair database before condemning a part.
4. Symptoms of a Bad Fuel Pump Relay
A failing relay can produce several different complaints:
1. Crank, no start. The starter spins the engine normally, but the pump does not prime and the engine never fires.
2. Engine starts, then stalls. A relay with overheated contacts may work cold, then open as it warms up.
3. Intermittent no-start. The vehicle may start after sitting, after tapping the relay box, or after moving the relay. This is a sign of worn contacts, a weak coil, or a poor socket connection.
4. No pump hum with key ON. This can point to the relay, fuse, PCM command, inertia switch, wiring, or pump. It does not identify one part by itself.
5. Stalling while driving. Any fuel delivery interruption can be dangerous because power steering and brake assist may change when the engine stops. If this happens, move to a safe location and have the vehicle diagnosed before driving at highway speed.
6. Repeated relay failure. If a new relay fails quickly, look for a pump drawing excessive current, damaged wiring, water intrusion in the Power Distribution Box, or a poor terminal fit. Current overload, short circuits, and defective internal components are common relay failure causes.
5. How to Replace the Relay Safely
1. Park on level ground. Set the parking brake, turn the ignition off, and remove the key.
2. Let the engine cool. The Power Distribution Box is near hot engine parts and the battery.
3. Open the Power Distribution Box. Keep the cover and any diagram clean.
4. Locate R5. Match the position with the cover diagram or Owner Guide chart. If the lid diagram is missing, use the 1999 Owner Guide listing that identifies R5 as the fuel pump relay.
5. Pull the relay straight up. A gentle rocking motion can help. Do not pry hard against nearby fuses. If the relay is stuck because of corrosion or melted plastic, stop and inspect the box closely.
6. Compare the new relay. Check the shape, terminal count, terminal pattern, and part number. The replacement should seat fully without force.
7. Inspect the socket. Look for green corrosion, spread terminals, melted plastic, water stains, or loose pins. Clean minor surface corrosion with proper electrical contact cleaner and let it dry. Severe heat damage requires repair of the box or terminal.
8. Install the new relay. Press it in until fully seated.
9. Recheck F9. Confirm the 20A fuse is good.
10. Test the result. Turn the key to ON. Listen for the short pump prime. Start the engine and let it idle. Watch for a steady idle, no fuel smell, and no warning lights.
Some Ford guidance recommends disconnecting the battery before servicing the Power Distribution Box because the box has live power. Disconnecting the battery may reset the clock, radio presets, and learned idle strategy. Follow the safety instructions in your Owner Guide or service manual before working on live terminals.
6. When the Problem Is Not the Relay
If F9 is good, R5 is good, the inertia switch is reset, and the pump still does not run, the fault may be elsewhere.
1. PCM power and control. The PCM energizes the fuel pump relay. If the PCM does not have power, the relay may not activate. A failed PCM power relay can create a no-start that looks like a dead pump.
2. Wiring between the relay, inertia switch, and pump. Ford wiring discussions for this generation commonly identify a dark green/yellow wire feeding the inertia switch and a pink/black wire leaving it toward the pump on related Explorer/Ranger wiring. Use a proper wiring diagram for your exact model before testing or jumpering any circuit.
3. Inertia switch. A tripped switch or bad connector can stop power after the relay. Do not bypass it permanently. It is a safety device intended to reduce fire risk after an impact.
4. Fuel pump connector and ground. Check for voltage and ground at the pump connector. Low voltage from corroded wiring can make a good pump weak or silent. Access may require lifting the vehicle or reaching the tank area, so use jack stands and safe procedures.
5. Fuel filter. A restricted filter can lower pressure and strain the pump. The filter is commonly mounted along the frame rail on Ford trucks and SUVs of this era. Replace it at the service interval recommended for your vehicle, and make sure the new filter faces the correct direction.
6. Fuel pump module. If the relay side has correct power and ground, pressure is still low or zero, and the pump does not run with verified voltage, the in-tank pump may be worn out. Many replacement parts for 1999–2001 Explorer applications are sold as a complete module assembly that includes the pump, strainer, sending unit, and related internal parts. Replacing the complete module avoids dropping the tank twice for a separate failed gauge sender or strainer.
7. Real-World Diagnostic Notes for U.S. Owners
Use the VIN and engine code. The 1999 Explorer was sold with different engines and body configurations. Parts catalogs may ask for VIN, engine size, 2WD or 4WD, two-door or four-door, and production date. These details matter when ordering a pump, relay, filter, or module.
Check the easy parts at the parts counter. A relay and fuse are far cheaper than a fuel pump. Many auto parts stores can test a fuse or compare a relay. Bring the old relay with you and match the number printed on top.
Avoid guessing from forum posts about other Ford models. The 1999 Ford Expedition is a different vehicle. Some Expedition references list a #301 relay and a #10 fuse, while 1999 Explorer owner-guide information identifies R5 and F9. Always match the model year and model name.
Do not ignore a fuel smell. Gasoline vapor is flammable. Work outdoors or in a well-ventilated area. Keep sparks, cigarettes, heaters, and incandescent drop lights away from the work area. Have a Class B/C fire extinguisher nearby.
Relieve fuel pressure before opening fuel lines. Follow a Ford service procedure. Wear eye protection. Use line wrenches where needed. Clean around fittings before disconnecting them.
Use jack stands, not only a jack. Fuel pump replacement on this vehicle often requires working near or under the fuel tank. Never rely on a hydraulic jack alone.
Record what you test. Write down the fuse result, relay result, battery voltage, fuel pressure reading, and inertia switch condition. A shop can use those notes, and you avoid paying for tests you already completed.
8. Common Questions
Where exactly is the fuel pump relay on a 99 Ford Explorer?
It is R5 in the under-hood Power Distribution Box on the driver side of the engine compartment.
What fuse powers the fuel pump relay?
F9, a 20A mini fuse, is listed for the fuel pump relay and RAP module in the 1999 Explorer Owner Guide.
Is the fuel pump relay inside the cabin?
No. The cabin fuse panel is near the driver side lower dash area, but the fuel pump relay is in the engine-compartment Power Distribution Box.
Where is the inertia switch?
The 1999 Ford Explorer Owner Guide places the fuel pump shut-off switch in the front passenger footwell behind the kick panel.
Can a bad relay feel like a bad pump?
Yes. A bad relay can stop power to the pump and create a crank/no-start condition, stalling, or no pump prime. Test the circuit before replacing the pump.
Can I swap the relay with another one?
Only if the replacement relay has the identical part number, terminal layout, and rating, and the donor relay is known to be working. Put the correct relay back in its original position after testing.
How much fuel pressure should a 1999 4.0L Explorer have?
One published specification lists 57–73 PSI for the 1999 4.0L Explorer. Verify against a Ford service manual for your exact VIN and engine before making a repair decision.
Should I replace the pump or the whole module?
Many 1999–2001 Explorer applications use a complete in-tank module assembly. A complete module can include a new strainer, sending unit, and internal wiring, reducing the chance of another tank removal soon after the repair.
9. Recommended Replacement Fuel Pump: KEMSO
If testing confirms the pump itself has failed, consider a KEMSO Fuel Pump. KEMSO fuel pumps are engineered as high-performance OEM replacement parts and come with a lifetime warranty. That combination matters on an older Explorer: you want correct fitment, steady fuel delivery, and support after the sale, not a cheap part that leaves you dropping the tank again.
For U.S. owners who drive in hot weather, tow small trailers, commute daily, or keep an older Explorer as a family or work vehicle, a dependable pump is worth careful selection. Match the pump to your year, engine, VIN, and body style before ordering. A quality module with a fresh strainer and sending unit helps restore fuel delivery and fuel gauge operation at the same time.
Visit https://www.kemsoracing.com/ to review KEMSO Fuel Pump options, confirm fitment, and check warranty details before purchase.
10. Final Checklist
- Locate R5 in the under-hood Power Distribution Box on the driver side.
- Check F9, 20A, labeled “Fuel Pump Relay and RAP Module.”
- Reset the inertia switch behind the front passenger kick panel.
- Test or swap R5 with an identical known-good relay.
- Verify battery voltage, grounds, and socket condition.
- Measure fuel pressure before replacing the pump.
- Inspect wiring and the fuel filter if pressure remains low.
- Choose a complete module when the in-tank unit is confirmed bad.
- Use safe fuel-handling practices throughout the job.
- Confirm part fitment by VIN before ordering.
The quick answer remains simple: on a 99 Ford Explorer, the fuel pump relay is R5 in the Power Distribution Box under the hood, with the 20A F9 fuse feeding that circuit. Start there, then work through the fuse, relay, inertia switch, wiring, and pressure test. That order saves time, money, and unnecessary parts.
For a high-performance OEM replacement Fuel Pump backed by a lifetime warranty, visit https://www.kemsoracing.com/.