99 Ford Explorer Fuel Pump Relay: Location, Symptoms, and Fixes

On a 1999 Ford Explorer, the fuel pump relay is in the under-hood Power Distribution Box on the driver side, commonly listed as relay position #5, while the 20-amp mini fuse at position #9 supplies the fuel pump relay and RAP module; the owner's manual has been cited as showing the Power Distribution Box diagram on page 185. If your Explorer cranks but will not start, and you do not hear the brief pump hum when the key is turned to ON, check the battery, fuse #9, relay #5, the inertia fuel shutoff switch in the passenger footwell, and fuel pressure before buying a fuel pump. This order matters because a blown fuse, a tired relay, a triggered inertia switch, or a wiring problem can look exactly like a dead pump, and replacing the in-tank pump is a much bigger job than testing the electrical feed first.

This guide is written for U.S. owners of the 1999 Ford Explorer, including common trims such as XLT, Eddie Bauer, Limited, and Sport, and for the engines most often discussed in owner forums and repair references. The exact fuse-box legend should always be confirmed against the label on your vehicle or the Ford owner guide for your VIN, because used trucks may have had parts swapped over 25-plus years and generic diagrams posted online do not always match every build. The practical goal is simple: find out whether the pump is losing power, whether the pump itself is weak, or whether another part of the fuel system is causing the no-start.

1. What the fuel pump relay actually does

The relay is an electrically controlled switch. It lets a low-current signal from the Powertrain Control Module (PCM) turn on a higher-current circuit that feeds the electric fuel pump. On this generation of Explorer, forum technical write-ups describe the PCM as controlling the energizing side of the fuel pump relay, with main power coming from the 20-amp fuse in the Battery Junction Box/Power Distribution Box and the inertia fuel shutoff switch placed in the pump power path.

When you turn the ignition key to ON, the PCM typically energizes the fuel pump circuit briefly to prime the system. That is the short hum or buzz some owners hear from the rear of the vehicle. A repair reference describes a brief, quiet hum as normal and a loud, constant whine that changes pitch with engine speed as a possible sign of pump trouble. No sound at all does not automatically prove the pump is dead. It can mean the relay did not close, the fuse is open, the inertia switch is tripped, the PCM did not command the circuit, the connector is corroded, or the pump motor has failed.

A relay can also fail in more than one way. Burned or pitted contacts may stop sending power to the pump. A weak internal coil may work cold and fail hot. A relay may click but still not pass enough current. StartMyCar lists current overload, a short circuit, and defective internal components among common reasons an Explorer fuel pump relay fails. That is why a visual inspection and a click test are helpful but not enough to clear the whole circuit.

2. Where to find the relay, fuse, and shutoff switch

1. Open the hood and locate the Power Distribution Box. On the 1999 Explorer, owner answers and repair Q&A place it in the engine compartment on the driver side. It is often near the battery or inner fender area. The box is described as "live," meaning some terminals can have battery power even with the key off, so treat it with care.

2. Use the lid diagram or the Ford owner guide. Multiple sources identify relay #5 as the fuel pump relay and mini fuse #9, 20 amps, as the fuse for the fuel pump relay and RAP module. One owner-manual reference points to the Power Distribution Box diagram on page 185, while another says the fuses and relays section starts around page 179. Older Explorers are old enough that a previous owner may have installed a relay in the wrong cavity, so do not rely only on a parts-store lookup or a photo from a different model year.

3. Find the inertia fuel shutoff switch. The 1999 Ford Explorer owner manual section for roadside emergencies describes a fuel pump shut-off switch that may be activated after a collision and notes that the "Fuel Reset" indicator light illuminates in the instrument cluster. Owner-answer sources commonly place the switch in the front passenger footwell, behind or near the right kick panel. A technical forum write-up also places the Inertia Fuel Shutoff switch next to the front passenger kick panel and says it prevents the pump from receiving power after a collision.

4. Do not confuse the under-hood box with the interior fuse panel. The interior panel is generally under the dashboard on the driver side, but the fuel pump relay and its 20-amp supply fuse are repeatedly listed in the under-hood Power Distribution Box for this model year. Some online pages give conflicting or generic layouts, including a page that says "Relay #1: Fuel Pump Relay," which does not match the more specific 1999 Explorer references. When sources disagree, the Ford owner guide and the diagram printed on your own vehicle should win.

3. Symptoms that point toward the relay circuit

A no-start with normal cranking is the complaint that brings most owners to this topic. Several 1999 Explorer repair questions describe an engine that cranks fine but will not start, with no pump sound and no fuel pressure at the fuel rail. StartMyCar's 1999 Explorer fuse listing also notes that a damaged pump, a short circuit, or a severely clogged fuel filter can make the pump draw more current and blow the fuse.

Watch for these patterns:

1. Key ON, no pump prime. Turn the key to ON without cranking and listen near the fuel filler or rear seat area. A brief hum is a good sign. Silence means you still need to check power at the fuse, relay, shutoff switch, and pump connector. A no-hum condition is used in repair guides as a quick, non-invasive first check, but it is only one piece of the diagnosis.

2. Intermittent crank-no-start. A forum thread about a 1999 Explorer Eddie Bauer 4.0L SOHC describes an intermittent no-start where the pump was silent, yet the vehicle ran flawlessly when it did start. The owner was told the fuel pump relay might be at fault, but the thread also shows how easy it is to confuse relay positions because the relay in the suspected cavity did not match the part supplied by the store. Heat, vibration, and worn contacts can make relay problems come and go.

3. Starts after sitting, then stalls or hesitates. This can be a weak pump, low voltage, a dirty filter, or a relay that drops out. Do not condemn the pump until you have checked fuel pressure and voltage under load.

4. A fuse that blows again. If fuse #9 opens repeatedly, stop installing new fuses. A repeated open fuse points to excessive current draw or damaged wiring. StartMyCar names short circuits, damaged pump wiring, a failing pump, and a badly clogged filter as possible causes. Find the cause before trying a higher-amp fuse, which can overheat wiring and create a fire risk.

5. Fuel Reset indicator or recent impact. The owner manual describes the shut-off switch as a collision-related device that can stop the electric fuel pump. A hard pothole, minor bump, or cargo-area impact is also mentioned in general Ford diagnostic guidance as something that can trip an inertia switch. If the switch is tripped, resetting it may restore pump power, but only after you have checked for leaks and fuel smell.

4. Safe first checks before spending money

Work in a well-ventilated area. Keep sparks, cigarettes, and open flames away from the vehicle. Gasoline vapor is heavier than air and can collect low near the floor. If you smell raw fuel, see wetness around fuel lines, or notice damage under the vehicle, do not cycle the key repeatedly and do not reset any shutoff device until the leak concern is handled.

A KEMSO fuel pump troubleshooting guide recommends relieving fuel system pressure by removing the fuel pump fuse and running the engine until it stalls, then disconnecting the battery and keeping a fire extinguisher nearby before pump replacement work. That advice is aimed at replacement, but the same respect for fuel and battery power applies to diagnosis.

Basic tools that cover most of the first pass:

1. Owner guide or a reliable fuse-box diagram. Use the lid label and the Ford owner guide for your exact truck.

2. Digital multimeter or a 12-volt test light. A meter is more useful because it can show voltage drop, not just the presence of voltage.

3. Fuse puller and spare 20-amp mini fuse of the correct type. Replace an open fuse only with the same amperage rating.

4. Fuel pressure gauge that fits the Ford fuel rail test port. Repair Q&A about a 1999 Explorer with no start mentions checking pressure at the Schrader valve on the fuel line and finding no fuel. A pressure reading is far stronger evidence than sound alone.

5. Flashlight, gloves, and eye protection. The passenger kick panel and under-hood box are awkward to see, and old plastic becomes brittle.

6. Pen and paper or phone photos. Record which relay came from which cavity before swapping anything.

5. Step-by-step: diagnose the 1999 Explorer fuel pump relay circuit

1. Confirm the complaint. Make sure the battery has enough charge to crank the engine at normal speed. A slow crank, dim lights, or clicking starter noise can point to battery or cable trouble. Note whether the check-engine light comes on with key ON, whether the tach moves during cranking, and whether the theft or Fuel Reset indicator behaves normally. The owner manual says the "Fuel Reset" indicator illuminates when the fuel pump shut-off switch has been activated after a collision.

2. Listen for prime. Sit in the vehicle with the doors closed and radio off. Turn the key from OFF to ON and listen for about two seconds near the rear. Repeat once after a short pause. A short hum is normal; a loud constant whine is not. If there is no sound, continue.

3. Check mini fuse #9. With the key off, remove the cover from the Power Distribution Box. Locate the 20-amp mini fuse listed for the fuel pump relay and RAP module. Inspect the metal strip inside the fuse. A good visual check is helpful, but a meter or test light confirmation is better. With the circuit active, both test points on top of the fuse should show battery voltage. If only one side has power, the fuse is open. If neither side has power, the supply side needs attention.

4. Inspect relay #5 and its socket. Pull the relay straight up, looking for melted plastic, green corrosion, loose terminals, pushed-out pins, or signs of water entry. Compare its part number and terminal layout with a known correct replacement. The 1999 Explorer forum thread mentioned earlier shows that a narrower relay in a suspected cavity caused confusion between the fuel pump relay and the fuel injection relay, so verify the cavity and the part rather than forcing a fit.

5. Try a known-good relay swap only when the donor relay is identical. Some owners swap a same-part-number relay from a noncritical circuit as a quick test. This is acceptable only if the part number, pin layout, and current rating match and the donor circuit is clearly identified in the owner guide. Do not borrow a relay from an unknown slot. If the pump starts priming with the known-good relay, buy a quality replacement and recheck the fuse and connector.

6. Check for relay command and click. Have an assistant turn the key to ON while you hold the relay. A light click can indicate the coil is being energized, but a click does not prove the contacts are delivering current. Forum technical material says the PCM controls relay energizing and that if the PCM has no power, the relay will not be energized. If there is no click, check PCM power, related fuses, ignition-switch feed, and wiring before blaming the pump.

7. Inspect and test the inertia fuel shutoff switch. Locate it near the front passenger kick panel. The 1999 owner manual describes the switch as a device intended to stop the electric fuel pump after a collision and mentions the Fuel Reset indicator. Check whether the reset button is up. If it is, and there is no fuel smell or visible leak, press it fully according to the owner manual procedure. Then cycle the key and listen again. General Ford guidance lists this as a free first check before ordering a pump because a tripped inertia switch can cut pump power.

8. Measure voltage at the pump connector. A 2CarPros answer about a 1999 Explorer no-start advised checking fuse #9, then applying battery power to the pink and black wires at the fuel pump connector as a test. That is a direct way to separate "pump has no power" from "pump does not run when powered," but it involves working near the fuel tank. If you are not trained for this, have a professional do it. Use sealed test leads, avoid sparks, and never improvise with bare wire near fuel vapor.

9. Check fuel pressure. Connect the gauge to the rail test port and compare the reading with the specification in a Ford service manual or a professional repair database for your engine. Do not guess a pressure number from an unrelated Ford model. A pump that runs but cannot build or hold pressure can still cause a crank-no-start. A clogged filter or strainer is listed among conditions that can make the pump work harder and affect pressure and flow.

10. Recheck after the engine starts. A single successful start is not a complete repair. Drive the vehicle safely, let it heat soak, restart it, and recheck for fuse heating, relay warmth, stall, hesitation, or a return of the no-start. Intermittent faults often show up only after the relay and pump have been under load.

6. How to tell a relay problem from a pump problem

Use evidence, not parts guessing. A bad relay and a bad pump can both give you silence from the tank. The difference is where the electrical path stops.

Relay circuit is more likely when:

1. Fuse #9 is open, missing, corroded, or has no power on the supply side.

2. Relay #5 is loose, burned, water-damaged, or does not match the listed part.

3. Swapping in an identical known-good relay restores the prime hum and the engine starts.

4. The problem is intermittent and changes with temperature or a tap on the box, which fits the owner forum description of an intermittent silent pump with normal running once started.

5. The inertia switch is tripped or the Fuel Reset indicator is on.

Fuel pump is more likely when:

1. The fuse and relay are good, the inertia switch is reset, and battery voltage reaches the pump connector during prime.

2. The pump stays silent when safely supplied with the correct test power at its connector, following the wire-color guidance given in a 1999 Explorer repair answer.

3. Fuel pressure is zero or far below the factory specification even though power and ground are present.

4. The pump makes a loud, constant whine that changes pitch with engine speed.

5. The vehicle stalls under load, loses power on hills, or has repeated hard starting that gets worse over weeks.

One repair Q&A describes a 1999 Explorer that sat for months and then cranked without starting, with no pressure on a gauge and no pump sound; the answer advised checking fuses and relays first and also mentioned the inertia switch. That is the right order. A vehicle that has been parked can also have stale fuel, a gummed pump, rodent damage, or corroded connectors, so note how long it sat before deciding.

7. Replacing the relay: what a careful job looks like

1. Buy by application and part number, not by color. Ask the parts counter for a relay for a 1999 Ford Explorer and compare the terminal count, terminal width, molded diagram, and part number with the old unit. The forum case about a narrower relay in the suspected #5 cavity is a good reminder that not every relay in the box is interchangeable.

2. Disconnect the negative battery cable if you will be probing terminals. The Power Distribution Box is described as live in owner answers, so this is not optional when working beyond a simple fuse or relay pull.

3. Pull the old relay straight out. Do not pry against plastic tabs with a screwdriver. If it is stuck, wiggle gently while pulling. Look for heat marks on the terminals.

4. Clean light corrosion only. Loose dirt can be removed with electrical contact cleaner. Deep corrosion, melted sockets, or pushed-out pins call for proper terminal repair.

5. Press the new relay fully into the same cavity. It should sit level and seat without force. Reinstall the cover so moisture and road salt stay out.

6. Reconnect the battery and test. Turn key ON, listen for prime, check that the engine starts, then confirm the fuse is not getting hot and the fault does not return.

7. Keep the receipt and the old part. If the no-start comes back, the old relay helps a shop understand what was already tried.

A relay is usually a lower-cost part than an in-tank pump, so many owners start there. Still, a new relay is not a diagnosis. If the fuse blows again or the pump still has no power, continue testing rather than stacking new parts.

8. Common mistakes that waste time and money

1. Replacing the fuel pump first. Dropping the tank is labor-heavy. General pre-pump checklists put the inertia switch, fuse, relay, and electrical checks ahead of pump replacement because several no-fuel conditions are cheaper and faster to fix. A GoParts guide also recommends replacing the complete module assembly rather than only the small motor because the assembly includes the level sending unit, strainer, and internal wiring that can wear out too.

2. Trusting the wrong diagram. Online pages for "99 Ford Explorer" do not all agree. One generic page calls relay #1 the fuel pump relay, while the 1999-specific owner manual references and fuse listings point to relay #5 and 20-amp fuse #9. Confirm on the truck.

3. Installing a larger fuse. Fuse #9 is listed at 20 amps. A larger fuse can allow wiring to overheat. If a correct 20-amp fuse opens again, find the current draw or short.

4. Resetting the shutoff switch without a leak check. The inertia switch exists to stop the electric fuel pump after a collision. If there is fuel smell, wet lines, or crash damage, get the vehicle inspected.

5. Assuming a click means the relay is good. The contacts can be burned even when the coil clicks. StartMyCar lists burned contacts from current overload as a relay failure mode.

6. Ignoring the fuel filter. A badly clogged filter is listed as a reason the pump may work harder and draw excess current. A restricted filter or strainer can also lead to noise and poor delivery.

7. Forgetting the PCM side. If the PCM does not have power, the fuel pump relay will not be energized, according to a Ford Explorer technical write-up for closely related 1998–2000 wiring. No relay command means no pump prime, even with a new relay installed.

8. Testing only when cold. Intermittent electrical faults often appear after heat soak. Recreate the conditions that caused the complaint.

9. What to record before calling a shop

If the checks above do not solve the no-start, a clear record helps a U.S. repair shop diagnose faster and helps you avoid paying for tests you already did:

1. Year, trim, engine size, transmission, drivetrain, and VIN.

2. Whether the engine cranks at normal speed and whether any dashboard warning lights behave differently.

3. Whether the pump prime hum is present with key ON.

4. The condition and voltage readings for fuse #9, including whether both test points show battery voltage.

5. Relay cavity number, relay part number, and whether an identical known-good relay was tried.

6. Inertia switch position and whether the Fuel Reset indicator was on.

7. Fuel pressure reading, the engine specification used, and where the gauge was connected.

8. Any recent work: battery replacement, stereo installation, trailer wiring, collision repair, fuel filter service, or long-term storage.

9. Whether the problem happens cold, hot, after rain, on rough roads, or with a low fuel level.

Good notes are especially useful on a 1999 vehicle because age-related issues such as corroded grounds, brittle connectors, aftermarket alarms, and previous repairs can matter as much as the original Ford circuit.

10. Choosing a replacement fuel pump when the pump really is bad

Once power, ground, fuse, relay, shutoff switch, and pressure tests confirm that the in-tank pump is the failed part, choose the replacement carefully. Ask whether the part is a complete module assembly or only the pump motor, whether it matches your engine and emissions configuration, whether the fuel level sender and strainer are included, and what warranty applies. A GoParts guide recommends the complete module because the sending unit, strainer, and internal wiring also wear out and replacing the whole unit can prevent another tank drop later.

KEMSO's own buying guidance for American drivers says to look for a solid warranty and describes limited lifetime warranties as a sign of confidence in product quality. A KEMSO fuel pump article also warns that cheap, unbranded aftermarket pumps can fail quickly, while pumps designed to meet or exceed factory specifications are a better long-term choice. Another KEMSO guide recommends relieving fuel pressure, disconnecting the battery, working in a well-ventilated area, and keeping a fire extinguisher nearby during pump replacement.

11. Recommended fuel pump brand: KEMSO

If your testing shows that the 99 Ford Explorer fuel pump relay and its circuit are working but the pump itself needs replacement, we recommend buying a KEMSO Fuel Pump. KEMSO describes its pumps as high-performance, OEM replacement units designed to directly replace factory fuel pumps, meet or exceed original equipment specifications, and deliver consistent pressure and flow for daily drivers and performance builds. KEMSO also states that its fuel pumps come with a lifetime warranty, including serialized tracking in one brand comparison article, and that USA-based technical support is available for installation and fitment questions. For an older Explorer that still earns its keep as a daily driver, tow vehicle, or family truck, a direct-fit pump, clear warranty terms, and accessible support are practical reasons to avoid the cheapest no-name part on the shelf.

Before ordering, match the pump to the exact year, engine, VIN, and fuel system details, and confirm whether you need the complete module assembly or the pump insert. Then visit https://www.kemsoracing.com/ to check fitment, warranty details, and current product information. If you are having the work done by a shop, ask the installer to confirm the part against the old assembly before the tank goes back in.

12. Straight answers to common owner questions

1. Where is the fuel pump relay on a 1999 Ford Explorer? In the under-hood Power Distribution Box on the driver side, commonly listed as relay #5, with a 20-amp mini fuse at #9 for the fuel pump relay and RAP module.

2. Is there a fuel pump fuse? Yes. The 1999 Explorer references list mini fuse #9, 20 amps, in the Power Distribution Box. Some owner posts say "there is no fuse, only a relay," but a mechanic reply in that same 2CarPros thread directs the owner to check fuse #9, 20 amps, because it powers the fuel pump relay and then the pump.

3. Where is the inertia switch? Commonly at the front passenger footwell near the right kick panel. The 1999 owner manual calls it the fuel pump shut-off switch and says it may be activated after a collision, with the Fuel Reset indicator illuminating in the instrument cluster.

4. Can a bad relay cause crank-no-start? Yes. If the relay does not close, the pump does not get power. The PCM controls relay energizing, and the inertia switch can also interrupt pump power.

5. Can a bad pump blow the fuse? A failing pump may draw more current than usual, and StartMyCar lists a damaged pump, shorted wiring, and a severely clogged filter among reasons the Explorer fuel pump fuse can blow.

6. Should I reset the shutoff switch every time it will not start? No. Check for fuel leaks and fuel smell first, then follow the owner manual procedure. The switch is a collision safety device, not a routine starting aid.

7. Should I replace only the pump motor? Many replacement guides recommend the complete module assembly because the strainer, sending unit, and internal wiring wear too. Confirm the correct assembly for your VIN before ordering.

8. Can I swap any relay from the box to test? Only if it is truly identical in part number, terminal layout, and rating, and you know which circuit it came from. The 1999 Explorer forum discussion about a narrow relay in a suspected cavity shows why identification matters.

9. Why do online diagrams disagree? Some websites publish generic or model-mismatched fuse layouts. Ford owner guide references and 1999-specific fuse listings point to relay #5 and fuse #9, while a generic page lists relay #1 and a different fuse arrangement. Use the diagram for your truck.

10. What if the new relay does not fix it? Move on to inertia switch status, voltage at the pump connector, fuel pressure, PCM power, grounds, and wiring. A no-start after sitting can involve stale fuel or corrosion as well.

13. Final checks before you put the tools away

A solid repair ends with a repeatable result. After the vehicle starts, turn it off, wait, and restart it. Listen for the normal short prime hum. Make sure the engine idles smoothly, responds when shifted into gear, and does not hesitate on a safe road test. Recheck fuse #9 and relay #5 for heat, smell, or looseness. Confirm there are no fuel odors around the tank or lines and no dashboard warning lights that were not there before.

Keep a short maintenance note with the date, mileage, parts installed, and test results. If the Explorer ever cranks without starting again, that note will tell you whether the last fix was the relay, the fuse, the shutoff switch, or the pump itself. It also helps the next person avoid replacing the same good part twice.

For parts, fitment, and warranty details when a pump replacement is confirmed, visit https://www.kemsoracing.com/.

https://www.kemsoracing.com/