99 Ford Mustang Fuel Pump Relay Location: Quick Answer and Full Guide
On a stock U.S.-market 1999 Ford Mustang, the fuel pump relay is not a separate plug-in cube in the under-hood fuse box. It is inside the Constant Control Relay Module, usually called the CCRM. On 1999–2004 GT models, Ford location illustrations place that module in the right-front fender area beside the air-cleaner and intake route; on a left-hand-drive American Mustang, “right” means the passenger side . For 1996–2004 Mustangs, access normally requires removing the passenger-side front wheel and the inner fender liner, and the fuel pump relay is soldered to the CCRM circuit board rather than serviced individually . Start with the 20-amp Fuel Pump fuse in the engine-compartment Power Distribution Box, then check the inertia switch, PCM and CCRM power supplies, and the pump circuit before buying a CCRM or a pump .
The distinction matters because many parts catalogs and online answers show a conventional four- or five-pin relay. If you remove the cover from the 1999 Mustang’s under-hood box and look for a small relay marked “Fuel Pump,” you will not find one there. The box contains the fuse that protects the circuit; the switching component is inside the sealed module mounted farther back in the fender area .
1. The Short Answer, With the Exact Locations
Fuel pump relay: Inside the CCRM in the right-front fender area on a 1999 Mustang GT. Ford’s 1999 GT connector reference identifies the module connector as C192 .
Physical access: On 1996–2004 Mustangs, the module is on the passenger-side inner fender. Remove the front wheel and inner fender liner for access. A 1998 wiring-diagram reference places the CCRM inside the right-front fender behind the air-filter housing; Mustang technical discussions describe it just aft of the intake-tube opening and behind the wheel-well liner .
Main fuel pump fuse: 20-amp fuse 14 in the engine-compartment Power Distribution Box . Another 1999 fuse chart labels the corresponding mini-fuse “FUEL PUMP” and lists it as protecting the fuel pump relay .
Fuel pump shut-off switch: Ford calls this the fuel pump shut-off or inertia switch. The 1998 Mustang Owner Guide places it on the left side of the trunk behind the trunk liner; other Mustang references describe it near the left tail light . It interrupts the electric fuel pump after a substantial jolt.
Cabin fuse panel: Below and to the left of the steering wheel, near the brake pedal . It contains control-related fuses, including fuse 34, 20 amp, for the instrument cluster, CCRM, data link connector and SecuriLock transceiver, and fuse 35, 15 amp, for the shift-lock actuator, PCM, speed-control servo and ABS module . These are not the main 20-amp fuel pump fuse, but they belong in a no-start check.
Fuel pump: In the fuel tank on this generation. A pump replacement generally means supporting the vehicle safely, lowering the tank, disconnecting the lines and wiring, and replacing the module or pump assembly. Do not start there just because the pump is quiet.
2. Why Ford Used a CCRM Instead of a Normal Fuel Pump Relay
The CCRM combines several high-current switching functions in one sealed assembly. A Mustang CCRM reference lists power paths for the cooling fan, A/C clutch, fuel pump driver module or fuel pump supply, and PCM power relay . A MustangForums technical reply describing a 1999 GT says the sealed module contains relays for the fuel pump, PCM power, A/C clutch and engine cooling fan, and that the module must be replaced if an individual internal relay fails .
That arrangement explains why unrelated symptoms can appear together. A car may have a fuel-pump prime problem and also an inoperative cooling fan or A/C clutch. It does not automatically prove the CCRM is bad, because the shared power feeds, PCM commands, wiring and fuses have to work before the module can do its job .
The GT is more complicated than a simple “relay sends battery power to the pump” circuit. Ford-based GT information says a relay inside the CCRM supplies a separate Fuel Pump Driver Module, or FPDM. The CCRM and FPDM are different components, so diagnosing the complete supply and control path is necessary before replacing either one . Use the correct wiring diagram for your exact engine and model year. A 1999–2004 GT pinout guide explicitly warns that V6, Mach 1, Cobra and Cobra R applications require their own diagrams .
3. How to Reach the CCRM Safely
Work on a level surface with the engine off, the key removed, and the battery negative cable disconnected when you are removing panels or unplugging electrical connectors. Keep tools away from the cooling fan, because fan circuits can be controlled electronically.
-
Confirm which side is which. For a U.S. left-hand-drive Mustang, the vehicle’s right side is the passenger side. Do not reverse it while leaning over the front of the car .
-
Loosen the passenger-front wheel lug nuts with the car on the ground. Raise the vehicle with a jack at the approved lift point, support it with a jack stand, and remove the wheel. Never rely on a jack alone.
-
Remove the fasteners holding the plastic inner fender liner. They may be screws, push clips or a combination. Keep them organized because brittle original clips are easy to break.
-
Pull the liner back or remove it. The module is mounted in the fender area near the air-cleaner and intake path. On a 1999 GT, Ford’s location illustration places it in the right-front fender area beside that route . A 1998 V6 reference describes it behind the passenger-side wheel-well cover, around the one-o’clock position when viewed from the wheel .
-
Identify the module before unplugging anything. Look at the connector, the part number on the label and the wiring colors. The 1999 GT connector is identified as C192 in Ford-based location references . Do not buy a replacement solely because the connector shape matches.
-
Inspect the connector. Look for corrosion, water intrusion, pushed-out terminals, melted plastic, loose pins and damaged insulation. A bad connection can produce the same crank-no-start symptom as a failed internal relay.
-
Refit the liner and wheel, then torque the wheel nuts to the vehicle specification. Reconnect the battery after the electrical checks are complete.
If you only need to inspect fuses or reset the inertia switch, do not remove the wheel and liner. Start with the simple, accessible checks first.
4. Fuse and Relay Charts for a 1999 Mustang
The engine-compartment Power Distribution Box contains the high-amp maxi-fuses and the mini-fuses. A 1999–2004 Mustang fuse chart lists the following relevant positions :
| Position | Rating | Circuit |
|---|---|---|
| 1 | 50A V8 / 30A V6 | Electric cooling fan; the V6 uses a circuit breaker |
| 6 | 40A | Interior fuse panel, instrument cluster and PCM |
| 14 | 20A | Fuel Pump |
| 24 | 20A | A/C Pressure |
| 26 | 30A | PCM |
| 27 | 20A | DRL module and fog-lamp relay |
A separate 1999 diagram uses descriptive labels rather than numbers. It lists FUEL PUMP, 20A mini, Fuel Pump Relay; PCM POWER, 30A maxi; FAN (4.6L), 50A maxi, Constant Control Relay Module; and FAN (3.8L), 30A circuit breaker, Constant Control Relay Module . Published diagram numbering can vary, so use the cover legend, the molded label and a 1999-specific wiring manual for your exact car.
The passenger-compartment fuse panel is below and to the left of the steering wheel by the brake pedal . Relevant circuits in the 1999–2004 chart include :
- Fuse 2, 20A: Engine Controls.
- Fuse 8, 20A: Engine Controls.
- Fuse 34, 20A: Instrument Cluster, CCRM, Data Link Connector and SecuriLock transceiver.
- Fuse 35, 15A: Shift Lock Actuator, PCM, Speed Control Servo and ABS Module.
- Fuse 33, 15A: Stop Lamp Switch and Speed Control Deactivation Switch.
The fuel-pump fuse is under the hood, not in that cabin panel . Use the exact fuse type and amperage shown for the car. Never use foil, a coin, wire or a higher-rated fuse to bypass a blown fuse; that can damage the harness and create a fire risk .
5. A Practical Crank-No-Start Diagnostic Order
A silent pump does not identify a failed pump by itself. The PCM, fuses, CCRM, inertia switch, wiring, grounds and pump all have to work. This order keeps the least expensive and most accessible checks first.
-
Check the obvious items. Confirm that the battery is charged, the engine cranks at normal speed and the tank actually contains fuel. A false gauge reading is possible on an older car. If you smell gasoline or see a leak, stop and repair that first.
-
Look at the 20A Fuel Pump fuse. On the 1999 chart, it is position 14 in the engine-compartment box . A visual check is useful, but testing both exposed test points with a test light or multimeter is more reliable. If it is blown, find the cause before installing another one.
-
Check PCM, engine-control and CCRM-related fuses. The PCM needs power before it can command the relay circuit correctly. A 1998 Mustang diagnostic reference emphasizes checking the main fuel-pump fuse along with PCM and CCRM fuses because a computer without power cannot command the pump properly .
-
Check the trunk inertia switch only when there is no fuel leak. Ford’s procedure begins with the ignition OFF and a fuel-system leak inspection. The switch is designed to stop the electric pump after a substantial jolt . Do not repeatedly reset it if you smell fuel or find damaged lines.
-
Listen for the brief key-on prime. Turn the key to ON without cranking and listen near the rear of the car. A normal pump usually runs briefly, then stops. No sound is not proof of a bad pump; it tells you to test the circuit.
-
Check voltage and ground during the prime window. Test at accessible connectors using a wiring diagram for the exact engine. A 1998 Mustang no-power-to-pump diagnostic guide recommends checking whether power reaches the CCRM, whether the PCM provides the control that energizes the fuel pump relay, and whether the CCRM sends power toward the pump . That is the right sequence: fuse, PCM command, CCRM output, inertia switch, wiring, then pump.
-
Inspect the CCRM connector and harness. Look for heat damage, corrosion and loose terminals. The 1999 GT Ford-based guide includes continuity and supply checks, such as a battery-supply check above 10.5 V under the specified key-on, engine-off conditions, and resistance checks for certain relay coils . Those values belong to specific pinpoint-test branches. A single passing measurement does not prove the entire module is good .
-
Measure fuel pressure with the correct gauge and specification. A 1998 Mustang reference gives an engine fuel-system pressure range of 250–270 kPa, or 36–39 psi, for 3.8L, 4.6L SOHC and 4.6L DOHC applications, while stressing that the exact factory test condition for the vehicle and engine should be used . A pump can make noise and still deliver low pressure. A clogged filter or pressure-regulator problem also has to be ruled out.
-
Condemn the pump only after power, ground, pressure and the rest of the circuit are checked. If correct voltage and ground are present during the prime window and the pump does not run, or pressure remains low after the filter and regulator are known good, the pump becomes the likely cause .
6. Signs That Point Toward the CCRM
The CCRM controls more than one system. A combination of the following symptoms makes it worth testing the module circuit, although none of them is conclusive on its own:
- No key-on pump prime with a good fuel pump fuse and confirmed PCM power.
- Cooling fan problems at the same time as a no-start.
- A/C clutch that will not engage despite a charged system and correct command.
- Intermittent stalling that changes when the module connector or fender area is moved.
- Corrosion or water damage at the CCRM connector.
- No output from the module toward the fuel-pump circuit despite correct input power and PCM control.
The 1999 GT CCRM guide lists pin functions that include low-speed fan output, high-speed fan output, battery supplies, a fuel-system relay battery supply, PCM/engine-control power output and a relay output toward the FPDM supply path . Those details are useful to a technician with the matching Ford pinpoint test and connector chart. Do not probe terminals at random or apply battery voltage to a cavity based only on an online pin list.
7. Buying the Correct Replacement CCRM
A matching plug is not enough. Replacement coverage varies by year, engine and internal relay arrangement.
-
Match the exact year and engine. Ford-based GT information applies specifically to stock 4.6L 2V GT wiring and says V6, Mach 1, Cobra and Cobra R applications need their own diagrams .
-
Read the original module’s label. Compare the Ford engineering number and suffix with the supplier’s application listing.
-
Check catalog restrictions. A 1999–2004 GT guide notes that A/C-relay arrangements changed for 2001 and that replacement catalogs distinguish earlier and later 4.6L applications . One supplier catalog begins its 4.6L coverage in 2001 even though its broad heading starts at 1999, so reading only the headline can lead to the wrong part .
-
Use the correct year’s connector and test information. The 1999–2001 GT connector is identified as C192, while 2002–2004 GT applications use C1262 in the Ford-based location references .
-
Do not assume all CCRMs interchange. Mustang technical references warn that V6 and V8 units differ, and that 2001–2004 units differ from earlier ones .
-
Test before replacing. A module can receive correct power and still fail internally, but a missing PCM command or a damaged wire will make a new module behave the same way.
8. When the Fuel Pump Itself Is the Problem
Once the electrical side checks out, look at the mechanical side. Common reasons to suspect the in-tank pump include a pump that receives correct power and ground but does not run, weak pressure with a known-good filter and regulator, loud whining, repeated fuse failure caused by a pump drawing too much current, or a car that stalls hot and restarts after cooling.
A fuel pump’s service life is affected by heat, contamination, low fuel level and poor-quality replacement parts. Fuel helps cool and lubricate an in-tank pump, so repeatedly driving with the tank nearly empty can shorten its life. Electrical faults can also damage a pump motor, which is why diagnosing voltage, ground and current draw matters.
Before dropping the tank, work in a well-ventilated area, disconnect the battery, keep sparks and flames away, and keep a suitable fire extinguisher nearby. Relieve fuel pressure according to the factory procedure. Support the tank securely; it may still contain a substantial amount of gasoline even when the gauge reads low. Replace seals and inspect the fuel-level sender, strainer, lines and locking ring while the assembly is accessible. Check every connection for leaks before returning the car to service.
9. Common Mistakes That Waste Time and Money
-
Buying a standard plug-in relay. A 1999 Mustang uses the internal CCRM relay arrangement, not an individual fuel pump relay in the under-hood box .
-
Searching only the cabin fuse panel. The main 20A Fuel Pump fuse is in the engine-compartment Power Distribution Box .
-
Calling “right side” the driver side. Ford’s right-front location refers to the vehicle’s right, which is the passenger side on a U.S. left-hand-drive car .
-
Replacing the pump because there is no hum. A tripped inertia switch, blown fuse, missing PCM command, wiring fault or CCRM problem can produce the same symptom .
-
Resetting the inertia switch without checking for leaks. Ford’s reset procedure starts with the ignition OFF and a fuel-system leak check .
-
Using a higher-amp fuse for testing. This risks wiring damage and fire .
-
Mixing wiring diagrams from different engines and years. V6, GT, Cobra and later 4.6L applications have differences that matter .
-
Assuming a good resistance reading proves a good relay. The 1999–2004 GT guide warns that a passing relay-coil check does not prove the contacts can carry load, and that factory pinpoint-test branches must be followed .
-
Ignoring shared CCRM symptoms. Fan and A/C complaints can help locate the fault, but they do not by themselves prove the module has failed.
10. Frequently Asked Questions
1. Is the 1999 Mustang fuel pump relay in the fuse box?
No. The fuse is in the engine-compartment Power Distribution Box, but the relay is internal to the CCRM. The internal relay is soldered to the module circuit board and is not serviced separately on this generation; the usual repair is a complete CCRM .
2. Where is the CCRM on a 1999 Mustang GT?
Ford’s 1999 GT location illustration places it in the right-front fender area beside the air-cleaner and intake route, with connector C192 . On 1996–2004 Mustangs, removing the passenger-side wheel and inner fender liner is normally required for access .
3. What fuse powers the fuel pump circuit?
A 1999–2004 Mustang diagram lists engine-compartment fuse 14 as a 20A Fuel Pump fuse . A separate 1999 chart labels the 20A mini-fuse “FUEL PUMP” and says it protects the fuel pump relay .
4. Where is the inertia switch?
Ford’s Mustang Owner Guide information places the fuel pump shut-off switch on the left side of the trunk behind the trunk liner, near the left tail-light area . Check for fuel leaks before resetting it.
5. Can I jump the relay to drain the tank?
Do not improvise with jumper wires based on a generic diagram. The 1999 GT uses a CCRM and, in the GT circuit described by Ford-based information, a separate FPDM . Applying power to the wrong terminal can damage the PCM, module or harness. Use the year- and engine-specific wiring diagram and proper fuel-handling equipment.
6. Will a bad CCRM also affect the cooling fan or A/C?
It can, because the module handles those circuits as well as the fuel-pump and PCM power paths . Test the shared power supplies and controls before deciding that the module is the cause.
7. Are V6 and GT CCRMs the same?
Do not assume they are. Mustang references warn that V6 and V8 units differ, and replacement catalogs distinguish model years and applications .
8. Should I replace the fuel filter before the pump?
A restricted filter can cause low pressure and poor running, and it is a normal maintenance item. Check the maintenance history and measure pressure before replacing expensive parts. If the filter is old and the tank is already being serviced, replacing it is practical, but it should not be used as a guess in place of diagnosis.
11. Recommended Replacement Fuel Pump: KEMSO
When testing shows that the pump itself has failed, choose a replacement that fits correctly and delivers consistent pressure. We recommend KEMSO Fuel Pumps. KEMSO products are described as high-performance, OEM replacement fuel pumps built to meet or exceed factory specifications, with direct-fit installation and a lifetime warranty . For an older Mustang that may be a daily driver, weekend car or modified performance build, those features address the three things most owners care about: correct fitment, dependable fuel delivery and long-term protection.
- High performance: KEMSO pumps are designed for consistent fuel pressure and flow under demanding conditions .
- OEM replacement: They are engineered as direct replacements for the factory pump, with no modifications or adapters needed .
- Lifetime warranty: Every KEMSO fuel pump is backed by a lifetime warranty .
- Broad application coverage: KEMSO’s catalog covers many cars, trucks, motorcycles and powersports applications; verify the exact year, engine and part number before ordering .
To find the correct pump for your 1999 Mustang, visit https://www.kemsoracing.com/ and check the application listing before placing an order . If the car has been modified with a different fuel system, larger injectors, forced induction or an aftermarket pump module, confirm compatibility before choosing any replacement.
12. Final Takeaway
For the 99 Ford Mustang fuel pump relay location, look beyond the fuse box: the relay is inside the CCRM in the right-front, passenger-side fender area, usually accessed by removing the front wheel and inner fender liner . The 20A Fuel Pump fuse is in the engine-compartment Power Distribution Box, and the inertia switch is in the left side of the trunk . Check fuses, PCM and CCRM power, the shut-off switch, the brief key-on prime, wiring, voltage and ground, and fuel pressure before replacing either the CCRM or the pump . Use the correct 1999 wiring diagram for the V6 or 4.6L GT, match any replacement CCRM by exact application, and work safely around gasoline and electrical connectors.
For a replacement pump backed by high-performance OEM-style fitment and a lifetime warranty, visit https://www.kemsoracing.com/.