99 Ford Mustang Fuel Pump Relay Location: Quick Answer and Repair Guide
The short answer: On a stock 1999 Ford Mustang, the fuel pump relay is not a small cube you pull from the under-hood fuse box. It is inside the Constant Control Relay Module, usually called the CCRM. On this generation, the CCRM is mounted on the passenger-side inner fender, behind the front wheel-well liner, near the air intake area. The fuel pump fuse is in the Power Distribution Box under the hood, and the fuel pump shut-off switch is in the left side of the trunk. Because the relay is soldered inside the CCRM circuit board, Ford does not service it as a separate relay. When that internal relay is confirmed bad, the normal repair is to replace the complete CCRM with the correct unit for the car’s engine and model year.
That distinction saves Mustang owners a lot of time. A 1999 Mustang with a crank-no-start condition may need a fuel pump, but it may also have a blown fuse, a tripped inertia switch, a damaged wire, a poor connector, a PCM power problem, a CCRM problem, or a fuel pump driver module problem. Start with the simple checks before buying a pump or dropping the fuel tank.
1. What “99 Ford Mustang Fuel Pump Relay Location” Really Means
Many online answers are confusing because they use the word “relay” in two different ways.
- A normal plug-in relay: A small plastic relay that pulls out of a fuse box. This is what many drivers expect to find.
- An internal CCRM relay: A relay built into a sealed Ford module. The module contains several circuits in one housing.
The 1999 Mustang belongs in the second group. The CCRM handles several electrical jobs, including the cooling fan, A/C clutch, PCM power, and fuel pump power supply. If only the fuel pump relay inside that module fails, the whole module is usually replaced.
This is also why some parts stores list a generic relay that does not match what you see on the car. A parts listing for a different year, a different Mustang generation, or a universal relay can send you to the wrong place. Before ordering anything, confirm the year, engine, VIN, and whether the car still has its original wiring.
2. Exact Places to Check on a 1999 Mustang
1. Power Distribution Box under the hood
The Power Distribution Box is in the engine compartment. It contains high-current fuses that protect major electrical systems. The 1999 Ford Mustang Owner Guide first printing lists position 14 as a 20A mini fuse for the Fuel Pump in the high-current fuse chart. Another 1999-specific reference also identifies a 20A mini fuse, number 14, for the fuel pump in the engine-compartment Power Distribution Box.
Use the label on your own fuse box cover and the Owner Guide for your VIN and build date. Fuse charts can differ between printings, engines, and replacement parts. Do not rely only on a number from a forum post. Read the cover, match the words Fuel Pump, and use the correct fuse type and amperage. Ford’s manual also says to disconnect the battery before servicing high-current fuses and to replace the Power Distribution Box cover before reconnecting the battery.
2. CCRM on the passenger-side inner fender
For 1996–2004 Mustangs, the CCRM is on the passenger-side inner fender, and removing the wheel and inner fender liner is required for access. A 1999 GT discussion places it inside the right front fender, just behind the opening for the intake tube, with the wheel and fender liner removed for access. A 1998 V6 reference describes it behind the passenger-side wheel-well plastic cover, around the 1 o’clock position when looking at the wheel.
The module is a sealed unit with a large electrical connector. It is not the same thing as the black fuse box under the hood. If you are standing at the front of the car and staring into the Power Distribution Box, you are looking at the fuse location, not the complete relay module location.
3. Inertia fuel shutoff switch in the trunk
The 1999 Mustang Owner Guide says the fuel pump shut-off switch is on the left side of the trunk behind the trunk liner. Ford designed it to stop the electric fuel pump after a substantial jolt. The 1999–2004 Ford service manual also says electrical power to the fuel pump is provided through the inertia fuel shutoff switch, located in the luggage compartment.
If the car was hit, towed roughly, backed into something, or sat through a hard bump, check this switch. Do not reset it until you have checked for fuel leaks and fuel smell. Ford’s owner-guide procedure starts with the ignition OFF, a fuel system leak check, the reset step, then key ON and another leak check.
4. Passenger-compartment fuse panel
The cabin fuse panel is below and to the left of the steering wheel, near the brake pedal. It handles many interior and control circuits. Some cabin fuses are connected with CCRM, PCM, engine controls, instrument cluster, and data link circuits, so they matter during a no-start diagnosis. The main 20A fuel pump fuse listed in the 1999 Owner Guide, however, is in the under-hood Power Distribution Box.
This is a common mistake. A driver checks every small fuse under the dash, finds nothing wrong, and assumes the fuel pump circuit is fine. The main fuel pump fuse is under the hood.
3. Why Ford Used the CCRM
The CCRM combines several relays and control circuits in one module. On the SN95 / New Edge Mustangs, it can control power for:
- Cooling fan
- A/C clutch
- Fuel pump driver module or fuel pump power supply
- PCM power relay
A 1999 GT forum answer describes the module as sealed and says it includes relays for the fuel pump, PCM power, A/C clutch, and engine cooling fan. It also says the module must be replaced if any single relay goes bad.
That design means one CCRM problem can create more than one symptom. You may see a no-start, an cooling fan issue, or an A/C clutch complaint at the same time. It also means you should not condemn the module because of one symptom. Test power, ground, command, and output.
4. The 1999 Mustang Fuel System Is Different From Earlier Cars
The 1999–2004 Mustang uses a returnless fuel system. Ford’s service manual lists the main parts as the fuel tank, filler pipe, filler cap, fuel filter, a single fuel line for the returnless system, the fuel injection supply manifold with a differential pressure sensor and fuel temperature sensor, and the fuel pump and sender assembly.
The fuel pump and sender assembly includes:
- An inlet filter
- A check valve that maintains system pressure after the pump shuts off
- A pressure relief valve for overpressure protection if flow is restricted
Ford’s service manual also says the fuel pump is controlled by an electronic fuel pump driver module, enabled by the powertrain control module, or PCM. That matters for diagnosis. The pump is not simply switched on by a basic relay every time the key turns. The PCM, driver module, CCRM power supply, inertia switch, wiring, and pump all have a role.
If you are working from a repair guide written for an older 1994–1998 Mustang, check the year carefully. Sensor layout, fuel system details, wiring, and module strategy are not always the same.
5. Common Symptoms That Send Owners Looking for the Relay
Most people search for the relay location because the car has one of these problems:
- Engine cranks but does not start
- No pump hum when the key is turned on
- Engine starts, then stalls
- Long crank time before start
- Loss of power under load
- Hard restart when warm
- Fuel pump fuse blows again
- Diagnostic code related to the fuel pump circuit
None of these symptoms proves the CCRM is bad. A silent pump can come from a blown fuse, no PCM command, a bad ground, a failed inertia switch, an open wire, a corroded connector, a bad driver module, a weak pump, or an internal CCRM fault.
Forum advice often jumps straight to “replace the relay” or “replace the pump.” That approach gets expensive. A 1999 Mustang is old enough to have previous-owner wiring, alarm installations, stereo work, remote start parts, repaired connectors, and damaged harness sections. Treat the circuit as a circuit.
6. First Checks Before Buying Parts
Work in this order.
1. Confirm the basics
Check battery voltage, clean battery terminals, normal cranking speed, and actual fuel in the tank. Old fuel gauge senders can read wrong. Do not trust the dash gauge alone on a car that has been sitting. Look and smell for leaks. If there is a strong fuel smell or visible fuel, stop and fix that first.
2. Check the fuel pump fuse
Open the under-hood Power Distribution Box. Find the 20A Fuel Pump fuse, listed as position 14 in the 1999 Owner Guide first printing. Replace a blown fuse only with the same type and rating. Never install a higher-amp fuse to “test” the system. If a new fuse blows, find the cause before installing another one. Common causes include damaged wiring, a failing pump drawing high current, a clogged filter, corrosion, or a short in added wiring.
3. Check related fuses
Check PCM, CCRM, engine controls, and ignition-related fuses listed in the Owner Guide and the fuse-box cover. A PCM without proper power cannot command the fuel pump system correctly. The 1999 Owner Guide chart includes a 30A PCM maxi fuse in the high-current box, plus other related circuits. Use labels rather than memorized slot numbers when sources disagree.
4. Inspect the inertia switch
Go to the left side of the trunk behind the liner. If there is no fuel leak, follow the Ford reset procedure. After resetting, turn the key on and listen for the brief pump prime. Then check again for leaks.
5. Listen for the key-on prime
Turn the key from OFF to ON without cranking. Many fuel systems run the pump briefly at key-on. If you hear nothing, that is useful information, but it is not a final diagnosis. Quiet pumps, noisy cabins, and short prime windows can mislead you. A test light, multimeter, or scan tool gives better evidence.
6. Test for voltage and ground
A practical diagnostic order is:
- Power through the fuse
- PCM power and ground
- PCM command to the relay or driver circuit
- CCRM input and output
- Inertia switch
- Rear harness and pump connector
- Pump current draw and fuel pressure
A wiring-diagram-based discussion for this generation notes that the PCM provides the ground path that energizes the fuel pump relay coil; without that ground, the relay power contacts will not close. That is why checking voltage on only one side of the circuit can lead to the wrong conclusion.
7. How to Access the CCRM Safely
Tools usually needed:
- Owner Guide or reliable wiring diagram
- Basic hand tools
- Jack and jack stands
- Wheel chocks
- Socket set
- Trim clip tool or small screwdriver
- Multimeter or test light
- Work light
- Gloves and eye protection
Basic access steps:
- Park on a flat surface.
- Set the parking brake.
- Chock the rear wheels.
- Loosen the passenger-front lug nuts.
- Raise the front of the car and support it with jack stands.
- Remove the passenger-front wheel.
- Remove the fasteners holding the inner fender liner.
- Pull the liner back far enough to see the module.
- Locate the CCRM on the passenger-side inner fender, near the air intake area.
- Inspect the connector, pins, mounting, and wiring before unplugging anything.
Do not work under a car held only by a jack. Disconnect the battery when the service procedure calls for it, especially around high-current fuses and main power circuits. Keep tools away from the positive battery terminal when the battery is connected.
8. How to Tell Whether the CCRM Is Actually Bad
A CCRM fault is more credible when the test results line up. Typical signs include:
- Battery power is present at the module input.
- PCM and CCRM related fuses are good.
- The PCM is commanding the pump circuit during the prime window.
- The inertia switch and rear wiring can pass power.
- There is no proper output to the pump circuit from the module.
- The connector is clean, tight, and not damaged.
- Other CCRM-controlled systems may also act up.
Forum guidance for this generation recommends checking whether power reaches the CCRM, whether the computer provides the ground that energizes the fuel pump relay, and whether the CCRM outputs power to the pump. That is the right order. The module should be blamed after the rest of the path is checked, not before.
Also, CCRMs are not all interchangeable. V6 and V8 units differ, and later 2001–2004 units differ from older ones. Match the part to the exact year, engine, emissions setup, and part number. A used module from a different Mustang can create new problems.
9. Relay, Fuse, Inertia Switch, or Fuel Pump?
Here is a plain-language comparison.
Blown fuel pump fuse
The pump has no power through that protected circuit. A fuse that blows once may be a symptom of a short, high pump draw, a restricted filter, or damaged wiring. Do not keep replacing fuses without finding the cause.
Tripped inertia switch
The car may crank normally but not start after a jolt. The switch is in the left side of the trunk. Reset it only after checking for leaks.
Bad CCRM internal relay
The pump may stay silent even though the fuse is good. Other module-controlled circuits may also be affected. The module must be tested in the circuit, and the internal relay is not serviced separately.
Wiring fault
Power may be present at the front of the car but missing near the tank. Look for chafed harness sections near the rear axle, trunk, and fuel tank area. Check aftermarket alarm, remote start, stereo, and fuel pump wiring from previous owners.
Bad fuel pump
The pump may have power and ground but not run, run weakly, draw too much current, or fail to build proper pressure. A pump can be noisy, quiet, intermittent, or temperature-sensitive. Test before dropping the tank.
A no-start on a 1999 Mustang is rarely a one-part guessing game. Use test results to narrow it down.
10. Fuel Pressure and Pump Testing Notes
Fuel pressure testing should be done with the correct adapter and a gauge made for fuel injection systems. Follow the service manual procedure for the 1999 engine and returnless system. The 1999–2004 service manual describes the differential pressure sensor, fuel temperature sensor, single fuel line, and fuel pump and sender assembly. That system is different from older return-style setups, so use the right specification for the exact car.
Safety rules matter:
- No smoking, open flame, or lighted tobacco near fuel work. Ford’s service manual gives this warning because flammable mixtures may be present.
- Work in a ventilated area.
- Keep a fire extinguisher nearby.
- Relieve fuel system pressure before opening fuel lines.
- Use eye protection.
- Do not crank the engine with fuel lines open.
- Clean spilled fuel immediately.
- Disconnect the battery when the procedure requires it.
- Do not probe through wire insulation unless you seal the hole afterward.
- Keep test leads away from moving parts.
If you are not comfortable testing fuel pressure or electrical circuits, have a qualified shop do it. A fuel leak or a wrong test procedure is more expensive than a diagnostic fee.
11. Why Online Answers Conflict
Search results for this topic often disagree. There are several reasons.
- Different model years: A 1994–1998 answer may not match a 1999 car.
- Different engines: V6, GT, and Cobra details can vary.
- Different fuse-box printings: Slot numbers and fuse body styles can differ between guides.
- Modified cars: Engine swaps, aftermarket wiring, and replaced harnesses change what you see.
- Generic parts catalogs: Some listings use a standard relay description that does not match Ford’s CCRM design.
- Confusion between fuse and relay: The fuse is under the hood; the relay function is inside the CCRM behind the fender liner.
- Confusion with later cars: 2005–2009 S197 fuse layouts do not carry over to the 1999–2004 New Edge cars.
One result claims there is no fuel pump relay on a 1999 Mustang because there is no separate plug-in relay in the normal sense. Another result describes a relay in the Power Distribution Box. The practical answer for a stock car is more specific: the fuel pump relay function is inside the CCRM, and the module is behind the passenger-side front wheel-well liner. Always verify with the Owner Guide, a Ford wiring diagram, or the actual module and part number on the car.
12. Replacement Parts: What to Check Before Ordering
1. CCRM
Match by:
- Model year
- Engine size
- VIN
- Build date
- Ford part number
- Connector shape and pin layout
- Emissions package if listed
Do not buy only by color or by a general “94–04 Mustang” label.
2. Fuel pump fuse
Use the exact amperage and fuse style listed for the car. The 1999 Owner Guide first printing lists a 20A mini fuse at position 14 for Fuel Pump. Do not upsize the fuse.
3. Inertia switch
If the switch is damaged, corroded, or has been bypassed, replace or repair it correctly. Do not leave a safety device jumpered.
4. Fuel filter
A clogged filter makes the pump work harder and can raise current draw. On an older Mustang, replacing a neglected filter is sensible maintenance, but do not assume it fixes a no-power condition at the pump.
5. Fuel pump
Match the pump to the exact 1999 Mustang engine, fuel system, emissions setup, tank, and connector. The 1999–2004 Mustang uses a returnless system and a fuel pump and sender assembly with an inlet filter, check valve, and pressure relief valve.
13. When the Fuel Pump Really Is the Problem
A fuel pump becomes the leading suspect when the electrical side checks out and the pump still does not perform. Examples include:
- Correct voltage and ground at the pump connector during the commanded prime window
- Good fuse, inertia switch, PCM power, and CCRM output
- Pump does not run, or current draw is clearly abnormal
- Fuel pressure is below the factory specification for the exact engine
- Pump runs but cannot maintain pressure under load
- Pump is intermittent when tapped, warmed up, or left running
- The car has high mileage with an original pump
- The tank was run low repeatedly, which is hard on an in-tank pump
Before replacing a pump on an old Mustang, inspect the tank, strainer, connector, harness, and fuel condition. Old fuel, debris, rust, or a damaged connector can ruin a new pump.
14. A Recommended Fuel Pump Brand: KEMSO
If testing confirms the fuel pump itself needs replacement, consider KEMSO. KEMSO Fuel Pump products are high-performance, built as OEM Replacement parts, and backed by a lifetime warranty. For U.S. Mustang owners who want a direct replacement rather than guesswork from a generic listing, KEMSO is a practical option to check. Visit https://www.kemsoracing.com/ to review the available fuel pump applications and choose the correct part for your vehicle.
Match the listing to the exact year, make, model, engine, and connector before ordering. A good pump is only good if it is the right pump for the car.
15. Practical Repair Scenarios
Scenario 1: The car cranks after a hard bump and will not start
Check for leaks, then inspect the inertia switch in the left side of the trunk. If it has tripped, follow Ford’s reset procedure. If the pump still does not prime, move to the fuse and electrical tests.
Scenario 2: The fuel pump fuse is blown
Replace it once with the correct 20A mini fuse after inspecting for obvious wiring damage. If it blows again, test current draw and inspect the rear harness, connectors, pump, and any aftermarket wiring.
Scenario 3: The fuse is good but the pump is silent
Check PCM power and related fuses, the inertia switch, CCRM input and output, PCM command, rear wiring, and pump connector. Do not replace the CCRM until the control and power paths are checked.
Scenario 4: Cooling fan and A/C also act strange
Include the CCRM in the inspection because the module handles those circuits too. Check the connector for corrosion, loose pins, water intrusion, and heat damage.
Scenario 5: The car starts cold but stalls hot
Do not assume the relay. Test fuel pressure, pump current draw, electrical connectors, and sensor-related data. Heat can expose a weak pump, a failing module, or a wiring connection that opens when hot.
16. Owner Maintenance Tips for a 1999 Mustang
- Keep at least a quarter tank of fuel when possible.
- Replace the fuel filter on a sensible schedule.
- Fix fuel leaks immediately.
- Keep the Power Distribution Box cover installed and sealed.
- Do not splice into the fuel pump circuit with cheap connectors.
- Remove or properly repair old alarm and remote-start wiring.
- Inspect trunk-area wiring and connectors for water damage.
- Use the correct fuse rating every time.
- Keep the battery terminals clean.
- Save the VIN, build date, engine size, and current part numbers in your phone.
- Take photos before unplugging connectors.
- Use a real wiring diagram for electrical testing.
- Label any removed fasteners from the fender liner.
- Do not reuse damaged trim clips if they allow the liner to rub the tire.
- Recheck for leaks after any fuel system work.
These habits matter on a car that is more than 25 years old. Most hard-to-find electrical problems on older Mustangs come from age, corrosion, previous repairs, or modified wiring.
17. Frequently Asked Questions
1. Where is the fuel pump relay on a 1999 Ford Mustang?
Inside the CCRM on the passenger-side inner fender, behind the front wheel and wheel-well liner, near the air intake area. The relay is not a separate service part.
2. Is there a regular fuel pump relay in the under-hood fuse box?
On a stock 1999 Mustang, do not expect a normal plug-in fuel pump relay there. The under-hood Power Distribution Box contains the fuel pump fuse and other high-current fuses. The relay function is inside the CCRM.
3. Where is the 1999 Mustang fuel pump fuse?
The 1999 Owner Guide first printing lists position 14, 20A mini fuse, Fuel Pump, in the Power Distribution Box in the engine compartment. Confirm with the fuse-box cover and the Owner Guide for your exact car.
4. Where is the fuel pump shut-off switch?
On the left side of the trunk behind the trunk liner. It is also called the inertia fuel shutoff switch.
5. Can I replace only the fuel pump relay inside the CCRM?
Ford’s normal parts approach is to replace the complete CCRM. The relay is soldered to the module circuit board and is not serviced separately.
6. Can a bad CCRM cause a crank-no-start?
Yes, if the internal fuel pump relay or related power circuit fails. A failed relay can leave the engine cranking with no fuel pump operation. Other circuit faults can cause the same symptom, so test first.
7. Will a bad fuel pump blow the fuse?
It can. A failing pump may draw more current than normal. A short, damaged wiring, clogged filter, corrosion, or wrong fuse rating can also be involved.
8. Do all 1994–2004 Mustang CCRMs interchange?
No. V6 and V8 units differ, and 2001–2004 units differ from older ones. Match by part number and application.
9. Why does my 1999 Mustang have different wiring than the diagram?
Previous owners may have installed alarms, remote start systems, stereos, engine swaps, or replacement harnesses. Use the VIN, build date, and Ford wiring diagram, then trace the actual wires on the car.
10. Should I drop the tank right away?
No. Check the fuse, inertia switch, PCM and CCRM power, relay command, module output, wiring, and pump connector first. Dropping the tank is a bigger job and should come after the electrical side points to the pump.
18. Final Takeaway
For a stock 1999 Ford Mustang, the answer to 99 Ford Mustang fuel pump relay location is: inside the CCRM on the passenger-side inner fender behind the wheel-well liner. The 20A fuel pump fuse is in the under-hood Power Distribution Box, listed as position 14 in the 1999 Owner Guide first printing. The inertia shut-off switch is in the left side of the trunk. The car uses a returnless fuel system with a PCM-enabled electronic fuel pump driver module.
Do not replace parts because one forum post says so. Check power, ground, command, output, and fuel pressure in a logical order. If the tests confirm the pump is the failed part, choose the correct replacement for your exact Mustang, and consider KEMSO high-performance OEM Replacement Fuel Pumps with a lifetime warranty.
Visit: https://www.kemsoracing.com/