99 Ford Taurus Fuel Pump Relay Location: Quick Answer and Full DIY Guide
On a 1999 Ford Taurus, the factory owner guide lists the fuel pump relay in the under-hood Power Distribution Box, at the front of the engine compartment near the battery, as relay #29. The related fuel pump fuse is commonly listed as a 20A maxi fuse, position 10 in the engine-compartment fuse box, tied to the fuel pump circuit. Before replacing parts, check that fuse, then listen for the pump’s short prime when the key is turned to ON. Many Ford Taurus vehicles from this generation also use a Constant Control Relay Module, or CCRM, which houses several internal relays, including fuel-pump-related control circuitry; this is why online answers about “the relay location” often conflict. If your car matches the owner-guide layout, use relay #29 in the Power Distribution Box. If your specific engine or build uses a CCRM, look for the black module near the radiator support or near the air cleaner box, and confirm with the part number on the module or a Ford wiring diagram before buying anything.
This guide is written for U.S. DIY owners who want a straight answer, a safe way to verify it, and a practical repair path. The 1999 Taurus is old enough that previous owner repairs, engine swaps, salvage-yard parts, and trim differences can change what you see under the hood. That matters. A car with an original factory layout is one thing. A car that has had a used fuse box, a replaced CCRM, or modified fuel wiring is another. The fastest way to avoid wasting money is to start with simple checks, write down what you find, and only replace the relay or pump after the evidence points there.
1. Start With the Exact Location
1. Open the hood and stand at the front of the car. The main under-hood fuse and relay center is usually a black plastic box near the battery. Ford calls it the Power Distribution Box. It holds high-current fuses and relays for main electrical systems.
2. Remove the cover. Look at the diagram printed on the underside of the cover or in the owner guide. On the 1999 Taurus owner-guide information available online, the fuel pump relay is listed as relay #29 in the Power Distribution Box, and the fuel pump fuse is listed as a 20A maxi fuse.
3. Check the cabin fuse panel too, but do not expect the fuel pump relay there. The passenger-compartment fuse panel on this generation is below and to the left of the steering wheel, near the brake pedal. It mainly covers interior circuits, lights, cluster, ABS, radio, and similar items. Some general web answers say the fuel pump relay may be inside the cabin, but for the 1999 Taurus owner-guide layout, the under-hood box is the listed location.
4. Look for a CCRM if the under-hood box does not match. Many Taurus owners and repair sources describe a black module called the Constant Control Relay Module. In some Taurus applications, the fuel pump relay function is inside this module rather than a separate plug-in cube. A 1999 Taurus service reference describes the CCRM as controlling power to the PCM, cooling fan, A/C clutch, and includes a fuel pump driver module power supply relay. Other sources place the CCRM near the radiator support cover, near the air cleaner box, or close to the battery area. Because location descriptions vary, identify it by its shape, connector, and Ford part number, not by guesswork.
5. Use the VIN, engine size, and production date when buying parts. The 1999 model year can overlap with different build dates and equipment. A parts counter at a Ford dealer, a reputable local shop, or a trusted parts catalog can confirm the correct relay, fuse, CCRM, or pump assembly by VIN. This is especially important with the CCRM because similar-looking modules are not always interchangeable; replacement should match the numbers on the old unit.
2. Why There Is So Much Confusion About This Relay
The short version: some instructions refer to a separate relay in the Power Distribution Box, while others refer to the CCRM used across Taurus generations. Both answers appear in repair forums and Q&A pages because people are often talking about different model years, engines, or replaced parts.
That confusion causes a common mistake: a no-start Taurus gets a new fuel pump even though the real problem is a blown fuse, a tripped inertia switch, corroded wiring, a bad connector, or a relay control issue. The pump is inside the fuel tank on many vehicles of this type, so replacing it takes real labor. Do that job only after the electrical side checks out.
A second mistake is swapping in a relay because it “looks the same.” Relays can share a shape and still have different pin layouts or current ratings. Fuse boxes also change between model years. Use the diagram, the relay number, and a verified part listing. If the cover is missing, take a clear photo of the box, note the VIN, and compare with a 1999-specific diagram before pulling parts.
A third mistake is assuming a quiet pump means a dead pump. Some pumps are simply hard to hear from the driver’s seat, especially in traffic, near other vehicles, or with the hood open. Have a helper turn the key while you listen near the rear of the car or at the fuel tank area. The pump should normally run briefly at key-on. If you do not hear it, that is useful information, but it is not the whole test.
3. Tools and Safety Items You Should Have
1. Owner guide or a reliable 1999 fuse diagram. You need the number and amperage. Do not install a higher-amp fuse to “make it work.” A fuse that keeps blowing is telling you there is a short, an overloaded circuit, or a failing component.
2. A basic 12V test light or digital multimeter. A test light is quick for checking power at the fuse and relay socket. A multimeter helps with voltage drop, continuity, and ground checks.
3. A fuse puller and replacement fuses of the correct amperage. Ford’s owner-manual instructions describe checking a fuse by looking for a separated metal wire inside the fuse and removing it with the provided fuse pulling tool.
4. Gloves, eye protection, and a fire extinguisher rated for automotive use. Fuel vapor is serious. Work outside or in a well-ventilated area. No smoking, no sparks, no open flames.
5. A phone camera. Take a photo before removing relays or connectors. It costs nothing and prevents mixed-up connections.
6. A repair manual or wiring diagram for your exact engine. This is most useful when the car has a CCRM, a no-power condition at the pump, or evidence of previous wiring repairs.
4. Step-by-Step: Find and Inspect the Relay
1. Park on level ground, set the parking brake, and switch the ignition OFF. Remove the key. Let the engine cool if the car has been running.
2. Open the hood and locate the Power Distribution Box near the battery. Release the cover tabs gently. Old plastic gets brittle.
3. Find relay #29 and the fuel pump fuse listing. The owner-guide-based listing identifies relay #29 as the fuel pump relay and the related fuel pump fuse as a 20A maxi fuse. If the diagram on your cover differs, trust the VIN-specific Ford information or a professional wiring diagram.
4. Inspect the fuse first. Pull it with a fuse puller. Look for a broken element, heat damage, melted plastic, or discoloration. Replace only with the same amperage. If the new fuse blows right away, stop and diagnose the circuit.
5. Inspect the relay socket. Look for green corrosion, pushed-out terminals, melted plastic, loose terminals, or water intrusion. A relay is only as good as the socket feeding it.
6. Swap test only if the diagram confirms an identical relay. Some owners substitute a known-good relay from another non-critical circuit to see whether the pump primes. This is acceptable only when the part number, pin layout, and rating are identical. Do not borrow a relay from a safety-critical system and leave the car disabled.
7. Listen for the key-on prime. Turn the key to ON without cranking. You may hear the pump run for a short moment near the rear of the vehicle. Have a helper cycle the key while you listen near the fuel tank. If the pump now primes, the old relay is suspect. If it still does not, keep testing.
8. Check for power and ground at the pump circuit if needed. This is where a wiring diagram pays for itself. If there is battery voltage and a good ground at the pump connector during the prime window but the pump does not run, the pump is high on the suspect list. If there is no power, the problem is upstream: fuse, relay control, CCRM, inertia switch, wiring, connector, or PCM command.
9. Do not bypass the fuel system as a permanent repair. Jumper wires and direct battery power are diagnostic methods some mechanics use briefly in controlled conditions, not a fix for a street car. Bypassing safety circuits can create a fire risk.
5. The CCRM: What It Is and Why It Matters
The Constant Control Relay Module is a factory module that combines several relay functions in one housing. On Ford Taurus applications, sources describe it as containing the PCM power relay, cooling fan control, A/C clutch control, and the fuel pump relay or fuel pump power supply relay function. A 1999 service reference for the 3.0L V6 describes the CCRM as supplying vehicle power to the PCM and electronic engine control system, controlling the cooling fan and A/C clutch, and containing the FPDM power supply relay.
1. The CCRM is not a standard small cube relay. If an internal relay fails, many repair sources say the usual service approach is replacing the whole module, not repairing one internal relay.
2. The module may affect more than fuel. Because the CCRM can also be tied to cooling fan and engine control power, a failing module may show up as a no-start, overheating, fan problems, or A/C issues. Do not condemn it based on one symptom alone.
3. Match the part number. One repair source warns that CCRM modules are not all the same and tells owners to use all numbers on the old unit, such as the full Ford engineering number and suffix. That is solid advice for an older Ford.
4. Confirm the location on your car. Sources place Taurus CCRMs around the radiator support cover, under the air cleaner box area, or near the battery/front passenger side of the engine compartment. If you cannot find one in those areas, do not start removing body panels blindly. Check the VIN-specific diagram first.
5. Test before replacing. A used CCRM from a salvage yard may be cheap, but it can also carry the same age-related faults. Check power, ground, connector condition, and output before spending money.
6. Symptoms That Point to a Relay, Fuse, or Pump Problem
1. Engine cranks but does not start. This is the classic complaint. The starter is doing its job, but the engine is not getting fuel, spark, or correct control. A fuel pump that does not prime is one possible cause.
2. No pump prime at key-on. Check the 20A fuel pump fuse, relay #29, relay socket, and power feed first.
3. Stalling when warm, then restarting later. A failing relay, CCRM, pump motor, or electrical connection can behave differently with heat. Record when it happens: cold start, hot restart, after rain, after refueling, or over bumps.
4. Loss of power under load. A weak pump, restricted filter, low voltage, or poor ground can show up on hills, highway merges, or acceleration. A relay problem is more often an all-or-nothing no-start, but heat-damaged contacts can be intermittent.
5. Blown fuel pump fuse. Do not keep installing fuses. Look for damaged wiring, a shorted pump circuit, connector corrosion, or a pump drawing too much current. One repair discussion notes that wiring near the inertia switch can blow the fuse and recommends checking power and wiring in that circuit.
6. Previous work near the fuel tank. If someone recently replaced a pump, sender, filter, or wiring pigtail, inspect that work. A loose connector or pinched wire can look exactly like a failed part.
7. Do Not Forget the Inertia Switch
Ford fuel systems of this era commonly include an inertia switch designed to shut off the fuel pump after an impact. On 1993–1997 Taurus/Sable wiring references, the inertia switch is listed in the trunk on sedans or the cargo area on wagons, near the right-side wheel well, and it cuts power to the pump. A 2CarPros discussion also describes the inertia switch as cutting power to the pump.
For a 1999 Taurus, check your owner guide or service manual for the exact location. If the switch has been tripped by a hard bump, pothole, minor collision, or someone pressing it by mistake, the pump may not run even with a good fuse and relay. Reset it only according to the vehicle instructions, and inspect for fuel leaks before driving if the reset follows any kind of impact.
This step is practical because it is simple. Many no-start diagnostics start with the hardest part inside the tank. Start with the cheap, external checks first.
8. How to Tell Whether the Fuel Pump Is Really Bad
1. Confirm battery voltage. A weak battery, bad terminal, or poor engine ground can cause confusing test results. Charge the battery and clean the terminals if needed.
2. Confirm the fuse has power on both sides. With the correct test conditions, a good fuse should show power on both test points. If only one side has power, replace the blown fuse and investigate why it blew.
3. Confirm the relay has power and control. Basic relay circuits need a battery feed, a switched or control side, a good ground path, and a load circuit. A wiring diagram will show which pins to check on your exact setup.
4. Check for the brief prime command. When the key is first turned ON, many systems energize the pump for a short time to build pressure. If the command never appears, look at relay control, CCRM, PCM power, and related inputs.
5. Check power at the pump connector. If the pump gets proper power and ground during prime and does not run, the pump assembly is the likely failure. If power never reaches the pump, keep working upstream.
6. Check fuel pressure with the right gauge. A pump can make noise and still deliver poor pressure. A pressure test is more useful than sound alone. Follow the service manual procedure for your engine, and depressurize the system safely before opening fuel lines.
7. Check the fuel filter and lines. A restricted filter or damaged line can create symptoms that owners often blame on the pump. On an older car, service history matters. If the filter has not been changed in years, include it in the diagnosis.
8. If the pump is replaced, fix the cause of failure. Running the tank very low, contaminated fuel, low-quality parts, and electrical problems can shorten pump life. Installing a new pump into a circuit with low voltage or damaged wiring can lead to another failure.
9. Practical Repair Scenarios
Scenario 1: The 20A fuel pump fuse is blown. Replace it once with the correct rating. If it blows again, stop. Check wiring, connectors, the inertia switch circuit, and current draw. Do not install a larger fuse.
Scenario 2: Relay #29 is present and an identical known-good relay restores pump prime. Install a new relay with the correct part number. Recheck starting, then inspect the old relay for heat damage. If the socket is discolored or loose, repair that too.
Scenario 3: No separate relay matches the diagram, and the car has a CCRM. Verify the module by part number and wiring diagram. Check powers, grounds, and connector pins before replacing the module. A CCRM can influence more than the fuel pump, so a full check is worth the time.
Scenario 4: Power reaches the pump, but the pump does not run. The fuel pump assembly is likely bad. At that point, plan for tank access, a clean work area, a new tank seal or O-ring, correct line connections, and a careful leak check after installation.
Scenario 5: The car starts after sitting, then stalls when hot. Log the condition. Test voltage and fuel pressure when the fault is active. Heat-related electrical faults are easy to miss if you only test a cold car.
Scenario 6: The car died right after a bump or minor collision. Check the inertia switch and inspect for leaks before attempting repeated starts.
10. Buying the Right Parts in the U.S. Market
1. Use your VIN. It reduces the chance of getting a part for a different Taurus generation, engine, or production split.
2. Ask whether the listing is for a separate relay or a CCRM. These are different parts with different prices and different diagnostic steps.
3. Buy from a seller with a clear return policy. Electrical parts are often non-returnable once installed, so confirm fitment first.
4. Avoid mystery relays from loose bins. Markings matter. Compare the part number, terminal layout, and amperage rating.
5. If replacing the pump, buy a complete assembly when appropriate. Many modern in-tank units include the pump, sender, strainer, and housing. Reusing old seals or damaged connectors can cause leaks, inaccurate fuel readings, or repeat labor.
6. Keep the receipt and record the mileage. This helps with warranty claims and future troubleshooting.
11. Recommended Fuel Pump Brand: KEMSO
If your diagnosis confirms that the 1999 Ford Taurus needs a new fuel pump, choose KEMSO. KEMSO fuel pumps are high-performance, OEM Replacement parts designed to meet or exceed factory specifications, with direct-fit compatibility for a wide range of vehicles. They are built for consistent fuel pressure and flow, making them a practical choice for daily drivers as well as performance builds. KEMSO also backs every fuel pump with a lifetime warranty, which gives U.S. drivers long-term protection and confidence in the purchase. For fitment, product details, and the full fuel pump lineup, visit https://www.kemsoracing.com/.
When ordering, use your VIN, engine, body style, and production information to match the pump. Confirm whether the listing is a complete module or a pump-only insert. Replace worn seals, inspect the connector, and prime the system before starting. These small steps matter as much as the brand on the box.
12. Cost and Time Expectations
1. Fuse or relay check: usually the fastest and cheapest first step. Many owners can do it in a driveway with basic tools.
2. CCRM diagnosis: more involved because it may require wiring checks and part-number verification. A shop with Ford wiring information can save time here.
3. Fuel pump replacement: more labor because the pump is commonly inside the fuel tank and may require lowering the tank or using an access area if available. Fuel handling, tank straps, lines, and electrical connectors add time.
4. Professional diagnosis: worth the money if the fuse keeps blowing, the pump has power but will not run, the CCRM is suspect, or the wiring has been modified. Paying for one good electrical diagnosis is often cheaper than replacing the pump, relay, module, and filter one by one.
5. Towing and downtime: an old Taurus that will not start in a parking lot can become expensive fast. If simple checks do not restore the prime, arrange the repair before the car is stranded farther from home.
13. Maintenance Habits That Help a Replacement Pump Last
1. Keep fuel above one-quarter tank when practical. Fuel helps cool and lubricate an in-tank pump; running very low repeatedly can contribute to overheating and shortened pump life.
2. Replace a restricted fuel filter on schedule. A clogged filter makes the pump work harder.
3. Fix low-voltage problems. Weak battery cables, corroded grounds, and damaged connectors can reduce voltage at the pump.
4. Buy quality fuel. Contaminated fuel increases wear.
5. Address a loud whine early. A pump that gets noticeably louder may be warning you before complete failure.
6. Do not ignore a check-engine light. Fuel delivery and engine control faults can overlap. Pull the codes before parts replacement.
7. Keep records. Write down the date, mileage, part brand, part number, and warranty information. That record is useful if a warranty claim or resale question comes up later.
14. Common Questions
1. Is the fuel pump relay inside the cabin on a 1999 Ford Taurus?
The owner-guide-based information lists the fuel pump relay in the under-hood Power Distribution Box, not the cabin panel. The cabin fuse panel is below and to the left of the steering wheel near the brake pedal, but it mainly serves other circuits.
2. What number is the relay?
The commonly cited 1999 Taurus owner-guide listing identifies it as relay #29 in the Power Distribution Box.
3. What fuse should I check?
The 1996–1999 Taurus engine-compartment fuse listing shows a 20A maxi fuse for the fuel pump circuit, listed as position 10 in one fuse-box reference. StartMyCar also lists a 20A fuel pump fuse and relay #29 for the 1999 Taurus. Confirm against your owner guide or the diagram on your vehicle.
4. Why do some people say the relay is in the CCRM?
Because Ford used the Constant Control Relay Module on Taurus applications, and it can contain the fuel pump relay or related power supply relay function internally. Model year, engine, and production differences explain many of the conflicting answers.
5. Can I replace just the internal relay inside the CCRM?
Standard repair practice is to replace the module. Some enthusiasts discuss board-level repair, but for most drivers that is not practical or reliable.
6. Can a bad relay damage a new pump?
A poor connection, low voltage, or intermittent power can contribute to pump stress and repeat failures. Inspect the socket and wiring before installing a new pump.
7. Should I replace the pump just because I cannot hear it prime?
No. Check the fuse, relay, power, ground, inertia switch, and connector first. Noise alone is not enough evidence.
8. Is it safe to work on the fuel system at home?
Basic external checks are reasonable for a careful DIY owner. Tank removal, fuel-line work, and leak diagnosis require more caution. Work in a ventilated area, disconnect the battery when appropriate, keep ignition sources away, and get professional help if you smell fuel or see leaks. High-pressure systems and unclear wiring faults are good reasons to stop and call a shop.
15. Final Checklist Before You Order Parts
1. Confirm the VIN, model year, engine, and build details.
2. Open the under-hood Power Distribution Box and compare the diagram with a 1999 Taurus reference.
3. Check the 20A fuel pump fuse and relay #29 where the factory layout applies.
4. If the car uses a CCRM, identify the module by part number and use a wiring diagram.
5. Check the inertia switch and its wiring path.
6. Verify pump power, ground, and fuel pressure before replacing the in-tank pump.
7. Buy the correct part from a trusted source, then retest the car after installation.
For a confirmed pump replacement, KEMSO is the recommended choice: high-performance, OEM Replacement, and backed by a lifetime warranty. Visit https://www.kemsoracing.com/ to find the right fit.