99 Ford Windstar Fuel Pump Relay Location: Quick Answer and Repair Guide
The 99 Ford Windstar fuel pump relay location is in the Power Distribution Box in the engine compartment. On a 1999 Windstar, look for relay 207, marked “Fuel Pump Relay,” in the under-hood fuse and relay box near the battery. The same box also contains the fuel pump motor fuse, fuse 5, 15A, and the relay control circuit fuse, fuse 20, 15A, which feeds the ignition coil, injectors, MAF sensor, fuel pump relay coil, and PCM on the 1999 model. The passenger compartment fuse panel below and to the left of the steering wheel by the brake pedal is a separate box and is not where the fuel pump relay is located.
This matters because many no-start checks go wrong at the first step. A 1999 Windstar has two fuse and relay areas, and online answers often mix up model years. The 1995–1998 Windstar used different inertia switch and relay arrangements. If you own a 1999 van, start with the under-hood Power Distribution Box, confirm the lid diagram and owner's manual labels, then test power and ground before ordering a pump.
This guide is written for U.S. owners and DIYers working on a 1999 Ford Windstar with the 3.0L or 3.8L V6. It uses Ford owner's manual fuse data, published fuse box diagrams, and practical diagnostic steps. Fuel system work involves gasoline vapor, pressurized lines, and electrical circuits. Work outdoors or in a well-ventilated area, keep sparks and flames away, wear eye protection, and have a Class B/C or ABC extinguisher nearby. If you smell raw gasoline, stop and fix the leak or get professional help before turning the key again.
1. Where To Look First
1. Open the hood and find the black Power Distribution Box near the battery. Ford's 1999 Windstar diagram places the Power Distribution Box in the engine compartment. Most owners find it close to the battery on the driver side of the engine bay. It has a removable or hinged plastic cover with a fuse and relay map. The cover may be tight; press down near the center while releasing the latch rather than prying hard on one corner.
2. Match the number on the lid or in the owner's manual. The 1999 diagram identifies relay 207 as the Fuel Pump Relay. Relay positions 201–209 are listed in the same section, with 206 marked “Not Used” and 208 marked “Not Used.” If a previous owner installed an aftermarket alarm, remote start, or stereo, look for added wiring or non-factory relays before assuming the factory layout is unchanged.
3. Check the two related fuses in the same box. The 1999 owner's manual and published diagram list these fuel pump circuit parts:
- Fuse 5 — 15A: Fuel Pump Motor, Powertrain Control Module.
- Fuse 20 — 15A: Ignition Coil, Intake Air Control Valve, Fuel Injectors #1–#6, Mass Air Flow Sensor, Fuel Pump Relay Coil, Intake Manifold Runner Control, HI-Speed Cooling Fan Relay Coil, LO-Speed Cooling Fan Relay Coil, Powertrain Control Module.
- Relay 207: Fuel Pump Relay.
4. Do not confuse this with the cabin fuse panel. The passenger compartment fuse panel is below and left of the steering wheel by the brake pedal. It handles interior circuits such as power points, radio, cluster, and other accessories. A cabin fuse labeled “20” in one diagram can be “Not Used,” while the under-hood fuse 20 is part of the engine and relay control circuit. Always use the section title “Power distribution box” when reading a 1999 Windstar chart.
5. Use the VIN and production date if the chart does not match. Ford sometimes changed connectors, calibrations, or running changes during a model year. The owner's manual in the glove box and the diagram molded into the box lid are the first two references to trust for your exact van. Repair manuals that cover 1999–2003 may show small year-to-year differences, so do not buy parts based only on a generic Windstar post.
2. Why Some Online Answers Say There Is No Relay
You may find forum posts or Q&A pages claiming the 1999–2003 Windstar has no replaceable fuel pump relay and that the PCM controls a circuit inside the Power Distribution Box. That claim can mislead a home repair. Published 1999 fuse box data and the owner's manual-based listings show a numbered relay 207 — Fuel Pump Relay in the Power Distribution Box, plus a fuse labeled “Fuel Pump Relay Coil”.
Here is the practical distinction:
1. The PCM controls the relay coil. When you turn the key, the PCM checks inputs such as the PATS anti-theft key status and whether the transmission control switch shows Park or Neutral. If those checks pass, the PCM provides ground to the fuel pump relay control coil.
2. The relay contacts carry pump power. Once the coil is energized, the relay closes its contacts and sends power toward the inertia fuel cutoff switch and then to the pump. A control problem, a bad relay, a blown fuse, a tripped inertia switch, a wiring fault, or a worn pump can all create the same “cranks but won't start” complaint.
3. A generic article may describe a different year or a different module. Some Windstar discussions cover 1996–1998 parts, the constant control relay module, or later Ford fuel pump driver modules used on other vehicles. Those are not the same as the 1999 Windstar layout shown in the 1999 owner's manual fuse charts.
4. The best answer is to test, not guess. Relay 207 is a known service part in the 1999 diagram, but replacing it without checking fuses, PCM control, inertia switch position, and pump power can waste time and money.
3. Tools That Make The Job Easier
1. Basic hand tools: a fuse puller or needle-nose pliers, a small flat trim tool, a flashlight, gloves, and safety glasses.
2. Electrical test tools: a digital multimeter, a 12V test light, and jumper leads with fused protection if you know how to use them safely. A scan tool that can read Ford PCM data is helpful but not required for the first checks.
3. Fuel system tools: a fuel pressure gauge with the correct Ford adapter, a line disconnect tool where required, and a drain pan rated for gasoline.
4. Reference materials: the 1999 Ford Windstar owner's manual, the diagram inside the Power Distribution Box lid, and a year-specific wiring diagram from a reputable repair database. Phone photos of the box before removing anything help put parts back in the right slots.
5. Replacement consumables: correct 15A mini fuses, dielectric grease for clean electrical terminals if appropriate, and a new fuel filter if service history is unknown. Never install a higher-amperage fuse to “test” a circuit. That can overheat wiring and damage components.
4. What The Fuel Pump Circuit Does On A 1999 Windstar
The pump is inside the fuel tank and needs clean power, a good ground, and a closed safety circuit. The Windstar fuel pump pushes gasoline from the tank to the engine so the injectors can deliver fuel under pressure. A bad pump can cause long cranking, stalling, whining from the tank area, sputtering at speed, loss of power during acceleration, or a no-start.
The published Windstar wiring explanation describes power flowing through two fuses to the fuel pump relay in the battery junction box. On the 1999 owner's manual chart, fuse 5 supplies the fuel pump motor and PCM, while fuse 20 supplies the relay coil side and several engine management components. Rick's Free Auto Repair Advice describes a 10A control coil fuse in the central junction box and a 15A contact fuse in the battery junction box for Windstar wiring in general; the 1999-specific owner's manual chart lists fuse 20 as 15A for the fuel pump relay coil circuit. That is one more reason to use the 1999 chart when working on a 1999 van.
The same wiring explanation notes that the PCM supplies ground to the relay coil only after key and Park/Neutral checks pass. Power then goes through the inertia fuel cutoff switch to the pump. The pump ground is identified as G101 in the lower left front of the engine compartment in that wiring article. Corrosion, loose terminals, damaged harness sections, and poor grounds can all imitate a dead pump.
5. Step-By-Step: Find Relay 207 And Check The Easy Items
1. Park on level ground, set the parking brake, and switch the ignition off. Remove the key. Let the engine cool if it has been running. Keep cigarettes, shop heaters, and sparks away from the work area.
2. Open the hood and locate the Power Distribution Box near the battery. Release the cover carefully. Brittle 1990s plastic can crack, especially after years of under-hood heat.
3. Read the map on the lid. Find 207 Fuel Pump Relay, fuse 5, and fuse 20. If the lid is missing or unreadable, use the 1999 owner's manual fuse chart or a reputable 1999-specific fuse diagram.
4. Inspect fuse 5 and fuse 20. Pull one at a time and look for a broken or melted internal strip. Replace only with the same amperage and type shown in the manual. If a new fuse blows right away or repeatedly, stop installing fuses and find the overload. Published causes include a short in the pump wiring, a failing pump drawing excess current, a severely clogged fuel filter, or a fuse with the wrong rating.
5. Check relay 207 seating. Press it firmly into place. Look for green corrosion, pushed-out terminals, melted plastic, or water tracks in the socket. A relay that has been loose can cause an intermittent no-start.
6. Swap only with an identical known-good relay for a quick test. Some owners test by swapping a same-part-number relay from a noncritical circuit, such as a matching horn or wiper relay, then returning everything to its original position after the test. Do this only when the part number, pin layout, and rating match. A wrong relay can feed power to the wrong pins.
7. Listen for the pump prime. With the radio, blower, and lights off, turn the key from OFF to ON without cranking. A working pump normally makes a brief hum or buzz from the rear of the van for a few seconds. No sound does not prove the pump is bad; it only tells you to check power, ground, relay control, and the inertia switch.
8. Do not keep cranking a dry or flooded engine. Long cranking can overheat the starter and wash cylinder walls with fuel. Work through the circuit checks instead.
6. Do Not Skip The Inertia Fuel Cutoff Switch
The 1999–2003 Ford Windstar inertia switch is in the jack storage compartment at the right rear corner of the vehicle. Open the rear hatch, remove the jack compartment cover, and look behind the thin foam covering toward the rear of the compartment. The switch has a red reset button on top. Make sure the button is fully depressed.
This switch cuts electrical power to the fuel pump after an impact. Rick's Free Auto Repair Advice notes that even a minor parking-lot bump can toggle it, producing extended cranking with no start. Answers and repair Q&A sources describe the right rear quarter panel or jack storage area for 1999–2003 vans. Older 1995–1998 Windstars are often described with the reset near the driver's left foot by the hood release, so check the year range before following a video or forum post.
Safe reset routine:
1. Turn the ignition off and remove the key.
2. Inspect for fuel odor, leaks, or collision damage. If you smell gas or see wet fuel lines, do not reset and start the van.
3. Press the red button fully down.
4. Turn the key to ON and listen for the pump prime.
5. Start the engine and let it idle while you watch for leaks or warning lights. If the switch trips again without an impact, have the circuit and switch inspected.
An inertia switch reset is a safety reset, not a repair for a fuel leak. Never bypass the switch to keep a damaged van running.
7. Symptoms That Point To The Relay, Fuse, Switch, Or Pump
1. Cranks normally, never fires, and no pump hum: Check fuse 5, fuse 20, relay 207, the inertia switch, pump power, and pump ground before condemning the pump. A defective relay can stop all power to the pump and create intermittent power loss, no-start, or unpredictable pump operation.
2. Starts cold, stalls when warm, then restarts after cooling: A weak pump, relay with heat-sensitive contacts, poor connector, or PCM control issue can be involved. Record how long it stalls and whether the pump prime sound returns when the van restarts.
3. Whining from the fuel tank: A high-pitched whine after pump prime can indicate a failing pump. A clogged fuel filter can also add strain and contribute to premature pump wear.
4. Sputtering at highway speed or power loss on acceleration: Low or inconsistent fuel pressure can cause these symptoms. Verify pressure with a gauge rather than replacing parts based on feel alone.
5. Fuse 5 blows again: Look for damaged or exposed pump wiring, a failing pump drawing excess current, a severely clogged filter, or an incorrect fuse rating. Do not upsize the fuse.
6. Check engine light with fuel pressure-related code: Some Windstar guidance notes P0087 as a low fuel rail pressure code, but a scan tool alone cannot separate an electrical fault from a mechanical pump fault. Use the code as one clue.
7. No-start after running the tank very low: Running low or out of gas can shorten pump life because the pump depends on fuel for cooling and lubrication. Add several gallons of fresh gasoline, cycle the key to ON a few times, and retest before assuming a new pump is needed.
8. A Practical Diagnostic Order That Saves Money
Use this order on a 1999 Windstar no-start. It moves from free checks to more involved tests.
1. Verify battery and starter operation. A weak battery can crank slowly and confuse PCM inputs. Charge or load-test the battery if cranking speed is low.
2. Confirm fuel level. Do not trust an old gauge on a high-mileage van. Add fuel if there is any doubt.
3. Reset the inertia switch only if safe to do so. Follow the right rear jack compartment procedure for 1999–2003 vans.
4. Inspect under-hood fuse 5 and fuse 20. Replace blown 15A fuses only with the same rating.
5. Identify relay 207. Reseat it or test with an identical known-good relay.
6. Check for a PCM-controlled ground at the relay socket. The Windstar PCM provides ground to the relay control coil after PATS and Park/Neutral checks pass. If that ground is missing, the problem may be an input, wiring, or PCM-related issue rather than the pump.
7. Check power at the pump connector and quality of ground. Rick's wiring guide recommends disconnecting the connector at the pump and checking for power and good ground; if missing, check the relay socket and transmission control switch. The guide identifies G101 in the lower left front of the engine compartment as the pump ground.
8. Measure fuel pressure. Use a gauge at the fuel rail service port and compare the reading with the Ford specification in a year-specific service manual. One Q&A source mentions about 30 psi as a rough check for a Windstar, but the correct spec for your engine and test conditions should come from Ford service data. Low pressure with good voltage and ground at the pump points strongly toward the pump, filter, regulator, or internal tank issue.
9. Inspect the filter and lines. A clogged filter can restrict flow, cause misfires or rough idle, and add strain to the pump. Look for leaks, kinked lines, rust, and damaged connectors.
10. Replace the pump only after the evidence supports it. A pump that receives proper voltage and ground but cannot build specified pressure is a much stronger candidate than a pump that never receives power.
9. Relay Testing Without Damaging The Circuit
1. Use a multimeter, not a screwdriver across terminals. You need to know which socket terminal has battery feed, which has the PCM-controlled ground, which is the relay coil feed, and which feeds the load. A wrong jumper can damage the PCM or back-feed a circuit.
2. Check voltage drop on the power side. A fuse can look fine while a corroded terminal still drops voltage under load. Measure at the relay socket and near the pump connector while the circuit is commanded on.
3. Check the ground side. A poor ground can make a good pump appear dead. Clean a factory ground only after disconnecting the battery, then restore the connection securely and protect it from corrosion.
4. Listen and feel for relay click. A click tells you the coil moved, not that the contacts carry current. Burned or pitted contacts can still fail under load.
5. Watch for heat and intermittent behavior. A relay or terminal that gets unusually hot, or a pump that works only after tapping the box, needs further inspection. Do not drive with an intermittent fuel cut.
10. When The Pump Itself Is The Problem
The 1999 Windstar fuel pump is inside the fuel tank. One replacement guide describes the pump as an in-tank unit beneath the vehicle near the rear passenger side and says the tank must be lowered for access. Kelley Blue Book also describes the Windstar pump as located inside the fuel tank and notes that a failing pump can cause no-start, stalling, reduced fuel flow, a check engine light, or a whirring sound from the tank.
Replacing a pump on an older minivan involves more than the pump motor. Inspect the tank, strainer, sending unit, lock ring, seal, electrical connector, and fuel lines. A complete module assembly can be easier than rebuilding a worn sending unit with a bare pump, but fitment must match the exact year, engine, emissions setup, connector shape, and tank design. Parts listings warn that 1999 Windstar pumps vary by trim and may depend on the 3.8L/3.0L engine and rectangular connector.
Before buying, confirm:
1. Model year, engine size, VIN, and build date.
2. Whether the van has the original tank and sending unit.
3. Connector shape and pin count.
4. Whether you need a complete module assembly, a pump insert, a strainer, a tank seal, or a filter.
5. U.S. emissions and fuel system configuration.
6. The seller's return policy and warranty terms in writing.
A low-price pump that fits poorly can leave you lowering the tank twice. On a vehicle this age, a complete assembly with a new seal and strainer is often the cleaner repair, but confirm the part number against the VIN.
11. Safe Fuel Pump Replacement Overview
This is an overview for understanding the job, not a substitute for Ford service procedures. Fuel tank removal can be dangerous if the tank is full, the vehicle is unstable, or fuel vapor is present.
1. Reduce fuel level. A nearly empty tank is lighter and safer. Siphon or drain only with approved equipment and legal storage containers.
2. Relieve fuel system pressure. Follow the Ford procedure for the 1999 Windstar. Wear eye protection and cover the service port with a shop towel.
3. Disconnect the negative battery cable. Keep the key out of the ignition.
4. Support the vehicle correctly. Use a level surface, wheel chocks, jack stands rated for the vehicle, and never rely on a jack alone.
5. Disconnect filler, vent, lines, and electrical connectors near the tank. Label or photograph connections. Cap open lines to keep dirt out.
6. Support the tank and remove straps carefully. Old fasteners may be rusted. Penetrating oil and hand tools reduce the chance of breaking a line.
7. Lower the tank enough to access the pump module. Clean the area around the lock ring before opening the tank so dirt does not fall inside.
8. Replace the pump or module with the correct seal. Compare old and new parts side by side, including inlet, outlet, float arm, connector, and strainer.
9. Reconnect and check for leaks before starting. Cycle the key to ON several times to prime, inspect every connection, then start and recheck.
10. Dispose of old gasoline and parts properly. Use an approved container and follow local hazardous waste rules.
If any step feels unsafe, have a professional shop handle it. Gasoline vapor can ignite from a small spark, and a fuel leak under pressure is not a driveway problem to ignore.
12. Cost And Time Expectations For U.S. Owners
A relay and fuse check can take under an hour and may cost only a few dollars for correct replacement fuses. A used-but-identical relay swap test costs nothing if you already own the spare. A fuel pressure gauge or multimeter is often cheaper than one incorrect pump purchase.
A full pump replacement costs more because of the part and the labor needed to lower the tank. Kelley Blue Book notes that a fair repair range for this older Windstar was not yet available in its pricing page, so local estimates can vary widely. Ask a shop to list diagnostic time, pump assembly brand, filter, tank seal, any rusted line repair, and warranty on parts and labor. A shop that replaces the pump without checking pressure, voltage, and ground may leave the original electrical fault in place.
13. Common Mistakes On The 1999 Windstar
1. Using a 1995–1998 inertia switch location. The 1999–2003 switch is described in the right rear jack compartment, while older vans use a different area.
2. Searching only in the cabin fuse panel. The fuel pump relay is in the under-hood Power Distribution Box; the cabin panel is below and left of the steering wheel by the brake pedal.
3. Replacing the pump before checking fuse 5, fuse 20, and relay 207. These are listed in the 1999 diagram and owner's manual-based charts.
4. Installing a larger fuse. Fuse ratings protect wiring. Replace with the same amperage and fix the cause of a repeat failure.
5. Ignoring the PCM control side. The PCM provides ground to the relay coil after anti-theft and Park/Neutral checks. A missing PCM ground can look like a dead pump.
6. Trusting a generic “no relay” post. Some Q&A pages say later Windstars have no single replaceable relay, but 1999-specific chart data identifies relay 207.
7. Running the tank near empty. Low fuel can shorten pump life.
8. Forgetting fitment details. 1999 Windstar pumps can vary by trim, engine, and connector type.
14. Maintenance Habits That Help An Older Windstar
1. Keep at least a quarter tank when practical. This helps reduce heat and strain on an aging in-tank pump.
2. Replace the fuel filter on schedule. A clogged filter can restrict flow and add load to the pump.
3. Fix fuel leaks and corrosion early. Moisture and road salt can damage connectors, grounds, and tank straps.
4. Keep the Power Distribution Box lid sealed. Water in the relay socket can cause intermittent no-start problems.
5. Note changes before failure. Longer cranking, a new whine from the tank, or brief power loss on hills deserves a pressure test before the van strands you.
6. Save the fuse map. Take a clear photo of the under-hood lid diagram and keep it in your phone. Older replacement lids and missing diagrams are common at salvage yards.
15. Quick Reference Chart
1999 Ford Windstar fuel pump electrical checks:
1. Main location: Power Distribution Box, engine compartment, near the battery.
2. Relay: 207, Fuel Pump Relay.
3. Pump motor fuse: Fuse 5, 15A, “Fuel Pump Motor, Powertrain Control Module”.
4. Relay coil and engine management fuse: Fuse 20, 15A, includes “Fuel Pump Relay Coil” and PCM-related components.
5. Second fuse panel: Passenger compartment, below and left of steering wheel by brake pedal; not the fuel pump relay location.
6. Inertia switch: Right rear jack storage compartment for 1999–2003; red reset button on top.
7. PCM control: Provides ground to relay coil after PATS and Park/Neutral checks.
8. Pump location: Inside the fuel tank; tank lowering is commonly required for access.
16. Recommended Replacement Fuel Pump: KEMSO
If testing confirms the pump is the failed part, consider a KEMSO Fuel Pump. KEMSO sells aftermarket fuel pumps for cars, motorcycles, ATVs/UTVs, and powersports applications through its U.S. online store. Its catalog includes vehicle-specific pump listings and a blog covering Ford fuel delivery repairs. For a 1999 Windstar, use the site's fitment tools or contact the seller with your VIN, engine size, connector shape, and part number before ordering.
KEMSO Fuel Pump products are high-performance, OEM Replacement units backed by a lifetime warranty. That combination is useful for an older daily driver or family van where reliable starting and consistent fuel pressure matter. Choose the complete assembly when the sending unit, strainer, or tank seal is also worn, and keep your receipt and warranty details with the vehicle service records.
Visit https://www.kemsoracing.com/ to review available fuel pumps and confirm fitment for your exact Ford Windstar.
17. Final Checklist Before You Order Parts
1. Did you confirm relay 207 in the under-hood Power Distribution Box?
2. Did you check fuse 5 and fuse 20 with the correct 15A rating?
3. Did you reset the right rear inertia switch only after checking for leaks and damage?
4. Did you confirm a PCM-controlled ground at the relay coil when the key is turned on?
5. Did you verify power and ground at the pump connector?
6. Did you measure fuel pressure against the correct Ford service specification?
7. Did you confirm pump fitment by year, engine, VIN, and connector?
8. Are you replacing the filter, strainer, and seal as needed?
When the electrical checks pass and the pump still cannot build pressure, the in-tank pump is the logical next repair. When power never reaches the pump, stay in the Power Distribution Box, relay control circuit, inertia switch, wiring, and grounds. This order keeps the repair focused and helps a 1999 Windstar get back to reliable starts without unnecessary parts.
For replacement fuel pump options, fitment help, and warranty information, visit https://www.kemsoracing.com/.