99 Honda Accord Fuel Pump Relay Location

The fuel pump relay on a 1999 Honda Accord is inside the cabin, in the driver-side under-dash fuse/relay box, below and to the left of the steering column, behind the lower dash cover. Honda service information calls the fuel pump control part of the PGM-FI main relay circuit, and the 1999 Accord factory manual describes removing the driver’s lower dashboard cover to reach the PGM-FI main relay 2 (FUEL PUMP) in the driver’s under-dash fuse/relay box . On this generation of Accord, do not start your search in the engine-bay fuse box. Start at the driver’s knees, look up under the dash, and use the fuse-box diagram to confirm the relay before ordering parts .

If your 1999 Accord cranks normally but will not start, stalls after it gets hot, or starts again after the cabin cools down, check this relay and its fuse before replacing the fuel pump. The relay is cheaper and easier to reach than the in-tank pump, and heat-related solder-joint failures are a known Honda problem on vehicles from this era . A no-start by itself does not prove the relay is bad. Confirm that the pump is not priming, then test the fuse, power, ground, and relay circuit.

This guide is written for U.S.-market 1999 Honda Accord sedans and coupes, including common LX, EX, and V6 trims. Electrical labels, fuse numbering, and relay names can vary with engine, trim, production date, and prior repairs. Use the diagram on your own fuse-box cover, the owner’s manual, or the factory service manual for your VIN as the final authority .

1. The exact location, explained in plain terms

Sit in the driver’s seat. The panel you need to remove is the lower dash cover directly beneath the steering wheel. It sits above the pedals and below the instrument panel.

Look toward the left side of the steering column. The under-dash fuse/relay box is mounted in that area, on the driver’s side. One fuse-box reference describes the under-dash box as being under the left side of the dash . An owner answer for a 1999 Accord also places the main relay to the left of the steering column, where its click can be heard and felt when the key is cycled .

Remove the lower cover for clear access. You may be able to see the bottom of the fuse box by lying in the footwell and looking upward with a flashlight. Removing the lower dash cover gives you enough room to identify the relay, inspect the connector, and unplug it without forcing the plastic. Factory troubleshooting instructions specifically call for removing the driver’s dashboard lower cover before removing the fuel pump relay .

Use the printed diagram. The diagram may be on the fuse-box cover or in the owner’s manual. Depending on the exact part and labeling, look for PGM-FI main relay, PGM-FI main relay 2 (FUEL PUMP), FUEL PUMP, or FP . Do not identify the relay only by color or by assuming that every rectangular black box in that area is the same part.

Check the nearby fuse. A 1999 Accord fuse-box listing identifies a 15-amp fuse in the driver’s under-dash box associated with the PGM-FI main relay and SRS unit circuit . Confirm the position and amperage against the diagram for your car. Never install a higher-amp fuse to get the car started.

Why some online answers are confusing

Search results for this car often mix three different names: fuel pump relay, main relay, and PGM-FI main relay. Older Honda models used a combined main relay that powered the engine computer and fuel system. Service information for later Accord circuits uses a separate name for PGM-FI main relay 2 (FUEL PUMP) in the under-dash fuse/relay box . Parts catalogs and repair forums may still call either unit the “main relay.”

Some general Honda guides say to look under the hood. That advice fits other years and models, but it can waste an afternoon on a 1999 Accord. For this car, the driver-side under-dash fuse/relay box is the primary location described by model-specific references .

2. What this relay actually does

The relay is an electrically controlled switch. When you turn the ignition to ON, the engine control system energizes the relay circuit so the fuel pump can run briefly and build pressure before the starter cranks the engine. Honda service information says the fuel pump should run for about two seconds when the ignition is turned to ON (II) . A Honda Accord forum reply describes the same event as a couple of clicks from under the dash followed by a soft whir from the rear of the car for two to three seconds .

The main relay circuit also supplies power to engine-management components. General Honda references describe the main relay as supplying the ECU, fuel-injection system, and related controls, while keeping the pump operating when the engine runs . That is why a failed relay can create a no-start that looks like a dead pump, a dead battery, or an ignition problem.

The important distinction is simple:

  1. The starter circuit turns the engine over.
  2. The relay circuit sends the command and electrical supply needed for fuel delivery.
  3. The fuel pump moves fuel from the tank to the engine.

If the engine cranks at normal speed, the starter is doing its job. The engine may still be missing fuel, spark, compression, or correct computer control. The two-second pump-prime check helps narrow the problem to the fuel-delivery circuit, but it does not automatically convict the relay.

3. Symptoms that point toward the relay on a 1999 Accord

1. Cranks but will not start. This is the most common complaint. The starter spins the engine normally, but the engine never fires. A missing fuel pump prime is a strong reason to check the relay circuit .

2. No two-second hum from the rear of the car. Turn the key to ON without cranking. With the fuel filler cap removed and a helper listening near the filler opening, you should normally hear the pump run briefly . Do this in a quiet garage, not beside a busy road. No sound means the pump is not running, but the cause can be a fuse, relay, wiring, connector, ground, or the pump itself.

3. Hot-weather no-start. Many Honda main-relay failures appear after the car sits in the sun or after a hot engine is shut off for a short time. The car may restart after the interior cools down . Heat causes repeated expansion and contraction inside the relay. Over time, solder joints on the circuit board can crack and make an intermittent connection .

4. Sudden stalling. An intermittent relay can open while the engine is running and cut power to the fuel pump or engine-management circuits. Some Honda diagnostic references list sudden stalling and intermittent no-starts among common main-relay symptoms .

5. The Check Engine Light behaves differently at key-on. Some Honda relay guides use the two-second bulb check as a clue to whether the ECU is receiving power . This is only a screening observation. A cluster bulb, ignition switch, battery, or ECU problem can produce a related result.

6. Unusual clicking or no click under the dash. One 1999 Accord owner describes locating the relay by hearing and feeling it switch as the key is turned on and off . A click does not guarantee that power is leaving the relay and reaching the pump. No click is a reason to check the control side of the circuit.

7. The problem comes and goes. A cracked solder joint may connect when cold and separate when hot. That is why a relay can pass a test in the morning and fail after lunch. Recreate the conditions that cause the complaint before declaring the part good.

4. Check these things before buying a relay or pump

1. Confirm the basics

A weak battery, corroded battery terminal, bad ground, low fuel level, blown fuse, or faulty ignition switch can send you in the wrong direction. Start with a fully charged battery and clean, tight terminals. Check the fuel gauge, but remember that a gauge or sending unit can be wrong.

If the car has been sitting for years, stale fuel, a clogged filter, or a seized pump may be involved. Those conditions are different from an intermittent hot no-start on a car that was driven yesterday.

2. Check the under-dash fuse

Use the fuse diagram for your exact car. A 1999 Accord diagram lists a 15-amp fuse associated with the PGM-FI main relay circuit . Pull the fuse and inspect it, but do not rely on sight alone. A test light or multimeter gives a better answer.

If the fuse is blown, replace it once with the correct amperage. If it blows again, stop. A repeated fuse failure suggests a short or an overloaded circuit that needs diagnosis. Do not keep installing fuses and do not bypass the fuse.

3. Listen for the pump prime

  1. Park in a quiet place and switch off all accessories.
  2. Have a helper turn the key to ON, not START.
  3. Listen near the open fuel filler for a brief pump sound.
  4. Repeat after switching the key off for several seconds.

Honda’s circuit troubleshooting procedure uses the pump sound as an early check and specifies a roughly two-second pump run at key-on . If the pump runs every time and the car still will not start, continue with fuel-pressure and engine diagnostics instead of replacing the relay on guesswork.

4. Feel and listen for the relay

With the lower dash cover removed, place a fingertip lightly on the relay while a helper turns the key to ON. A normal switching relay usually produces a small click. Cycling the ignition on and off has been used by Accord owners to locate the main relay by sound and feel .

A missing click may point to a control-side problem. A click followed by no pump sound may point to a blown fuse, damaged contacts, wiring, connector, or pump. Use a wiring diagram and a meter to separate those possibilities.

5. Inspect the connector and relay housing

Look for:

  1. Loose or pushed-out terminals
  2. Green or white corrosion
  3. Melted plastic or a burnt smell
  4. Water stains from a windshield or door seal leak
  5. A relay that is not fully seated
  6. Non-factory wiring, splices, or an aftermarket alarm or remote starter

A prior alarm installation or stolen-recovery repair can leave wiring that changes how the circuit behaves. Photograph the wiring before disconnecting anything.

6. Look for cracked solder joints

On older Honda main relays, cracked solder joints are a documented failure mode . If the plastic housing can be opened without damage, inspect the circuit-board joints under good light and magnification. Cracks can be very fine. Some repair guides discuss reflowing the joints, but replacement with a correct new relay is the more dependable choice for most owners. Soldering a circuit board requires skill, and a poor repair can create heat damage or a short.

7. Test voltage and ground, not just the part

Factory Accord troubleshooting gives a structured sequence: remove the driver’s lower dash cover, remove the fuel pump relay, turn the ignition to ON (II), and measure voltage at the specified connector terminal against body ground . The 1999 Accord factory manual also includes voltage checks at ECM/PCM connector terminals during the first two seconds after key-on .

You do not need to guess terminal colors from an internet post. Use the correct year, engine, and wiring diagram. A digital multimeter and a test light can tell you whether:

  1. Battery voltage is reaching the relay
  2. The ignition-switch control signal is present
  3. The ground path is good
  4. Voltage leaves the relay when it is commanded on
  5. Voltage reaches the pump connector

This is the point where “no pump sound” becomes useful evidence. If the relay receives the correct command and has good power and ground, but does not send power out, the relay is suspect. If voltage reaches the pump and the pump has a good ground but does not run, the pump is suspect. If voltage never reaches the relay, look upstream at the fuse, ignition switch, wiring, or ECM/PCM circuit.

5. Fuel pump relay vs. fuel pump: a practical comparison

What you observe Relay circuit is more likely when Fuel pump is more likely when
No-start pattern Fails hot, works after cooling, often intermittent Becomes steadily worse, with whining, low pressure, or eventual failure
Key-on sound No pump prime and no normal click, or an intermittent click Correct power and ground reach the pump, but it stays silent
Check Engine Light / ECU power Bulb-check or ECU-power clues are also abnormal Other systems behave normally at key-on
Voltage test Power enters the relay but does not leave when commanded Voltage and ground are present at the pump connector
Fuse condition Fuse is good; fuse blows only if another wiring fault exists Fuse may blow from a pump drawing excessive current
Repair access Under-dash relay is accessible after trim removal Pump is inside or accessed through the fuel tank area

A relay problem can imitate a bad pump so closely that many owners replace the pump first and still have the same no-start. A 1999 Accord forum reply recommends listening for the main relay clicks and the two-to-three-second pump sound before assuming fuel delivery is absent . General Honda guidance also warns that a missing prime supports a fuel-circuit problem but does not prove the relay has failed .

6. How to access and replace the relay safely

This is a low-cost electrical job, but sloppy work can damage the fuse box or trigger an airbag-related warning. The under-dash area is close to SRS wiring and the steering column. If you are not comfortable working there, have a qualified technician do it.

Tools that are useful

  1. A bright flashlight or headlamp
  2. A trim-panel tool or suitable screwdriver for the lower cover fasteners
  3. A digital multimeter or 12-volt test light
  4. The owner’s manual or fuse-box diagram
  5. A small mirror
  6. A phone camera for documenting connector positions
  7. Clean gloves

Step-by-step

1. Park the car on level ground. Set the parking brake, switch the ignition off, and remove the key.

2. Disconnect the negative battery cable. This reduces the chance of a short while working around the under-dash wiring. Follow the owner’s manual for any radio, power-window, or idle-relearn procedures that may apply after reconnection.

3. Move the seat rearward. Give yourself room to lie in the footwell or sit on the sill with your head under the dash.

4. Remove the driver’s dashboard lower cover. Factory Honda troubleshooting uses this step to reach the PGM-FI main relay . Support the panel as the last fastener comes out. Some covers also have clips or connections for diagnostic ports, hood release, or footwell lighting.

5. Find the under-dash fuse/relay box. It is on the driver’s side below the steering column .

6. Match the relay to the diagram. Look for PGM-FI, FUEL PUMP, or FP labeling. Do not pull a relay simply because it has the same shape.

7. Inspect before removal. Photograph the relay, connector, and surrounding components. Look for corrosion, heat marks, and loose terminals.

8. Release the relay. Some relays pull straight out. Others are held by a tab or a mounting bracket. Do not pry hard against the fuse-box plastic. If it is mounted to a bracket, release the bracket or retaining tab first.

9. Compare the replacement. Match the part number, connector shape, pin count, terminal layout, and mounting features. One Accord owner advises buying an exact match and notes that the connector may have as many as seven wires . A visually similar relay with different internal terminals can cause serious electrical damage.

10. Install the new relay. Push it fully into place until it is seated. Reconnect any harness connector and make sure it locks.

11. Reconnect the battery. Turn the key to ON and listen for the brief pump prime. Do not crank for long periods while the system is being checked.

12. Start the engine. Let it idle and watch for warnings. Then take a short test drive and include a hot restart after the engine reaches operating temperature. That is the condition most likely to expose an intermittent Honda relay fault.

13. Reinstall the lower dash cover. Make sure no wiring is pinched and all fasteners are secure.

7. Common mistakes that cost U.S. owners money

1. Replacing the pump without checking the relay. A cranks-but-won’t-start condition is not a pump diagnosis. A Honda-specific guide recommends checking the relay first because it is a common failure point and is cheaper than the pump .

2. Searching only in the engine-bay fuse box. The 1999 Accord’s relevant relay circuit is described under the driver’s dash . General instructions written for other Honda years may point to a different location.

3. Trusting a universal parts listing. Enter the year, make, model, engine, trim, and VIN when available. Honda changed electrical parts across generations, and used cars sometimes have swapped interiors or engine harnesses.

4. Swapping relays without checking the pinout. A known-good relay from another circuit can be useful in a controlled test, but only when the part number, pin arrangement, and electrical ratings match. An incompatible relay can feed power into the wrong terminal.

5. Ignoring a blown fuse. A fuse that fails again is a symptom, not an inconvenience. Find the cause.

6. Testing only when cold. If the complaint happens after a hot soak, test after a hot soak. Use a safe location where you can wait with the car parked.

7. Cranking the starter for long periods. Extended cranking heats the starter and drains the battery. Use short cranking attempts and let the starter cool.

8. Forgetting the basics. Low fuel, a weak battery, a bad ground, and a failed ignition switch are still possible. Confirm that the fuel pump is being commanded on and that the circuit can carry current.

8. What a shop will usually check

A competent shop should not replace a fuel pump based only on a no-start. Expect a process like this:

  1. Interview the owner about temperature, timing, and whether the failure is intermittent.
  2. Verify battery condition and cranking speed.
  3. Scan for diagnostic trouble codes, while understanding that an older relay fault may not set a code.
  4. Check the relevant fuses and the key-on pump command.
  5. Inspect the under-dash relay, connector, and wiring.
  6. Measure voltage and ground at the relay and pump circuits.
  7. Perform a fuel-pressure test when the circuit is powered.
  8. Recreate a hot no-start before signing off on the repair.

Factory service information uses terminal-specific voltage checks during the first two seconds after key-on and treats a suspect PGM-FI main relay as part of the circuit diagnosis, not as an automatic conclusion . Ask the shop what test result proved the relay or pump was bad. A clear answer should mention power, ground, or measured fuel pressure.

9. Parts, cost, and time expectations for the American market

A replacement main relay is usually far less expensive than a complete fuel pump assembly. Prices vary by brand, local parts availability, and whether you buy from a dealer, a national parts chain, or an online seller. The under-dash relay is also much quicker to access than an in-tank pump.

Expect a DIY relay inspection to take about 30 to 60 minutes the first time, mostly because removing the lower dash cover and working upside down is awkward. A direct replacement is often quicker once the panel is off. A shop may charge a diagnostic fee even if the relay itself is inexpensive, especially for an intermittent hot no-start.

When ordering, give the parts counter:

  1. Year: 1999
  2. Make and model: Honda Accord
  3. Body: sedan or coupe
  4. Engine: four-cylinder or V6
  5. Trim: LX, EX, or other
  6. VIN, when the catalog asks for it
  7. The name printed on your old relay, if readable

Keep your receipt and the old part until the car has passed a hot restart test.

10. If the tests show the fuel pump has failed

The relay may be healthy and the pump may still be the problem. Confirm power and ground at the pump, then check fuel pressure against factory specifications for your engine. A pump that receives correct voltage and ground but cannot produce pressure is a replacement candidate.

Fuel pumps on this era of Accord are associated with the fuel tank. Working around fuel requires real safety precautions:

  1. Work outdoors or in a well-ventilated area.
  2. Keep sparks, flames, and cigarettes away.
  3. Relieve fuel system pressure using the service-manual procedure before opening fuel lines.
  4. Disconnect the battery.
  5. Keep a Class B/C fire extinguisher within reach.
  6. Support the tank properly if it must be lowered.
  7. Replace seals and inspect fuel lines for cracking or leakage.
  8. Check for leaks before and after starting the engine.

A general fuel pump troubleshooting guide warns against cutting corners on an unbranded replacement pump and notes that low-quality materials can fail early when exposed to ethanol-blended fuels . American gasoline commonly contains ethanol, so choose a pump with clear fitment information and compatible materials.

11. Recommended replacement fuel pump: KEMSO

Once the relay, fuse, wiring, and pump circuit have been tested and the in-tank fuel pump is confirmed as the failed part, we recommend buying a KEMSO Fuel Pump. KEMSO products are described as high-performance, OEM Replacement, and backed by a lifetime warranty . KEMSO states that its pumps are engineered to meet or exceed factory specifications, with consistent fuel pressure and flow, and that its direct-fit replacements are designed for the original mounting location without modifying wiring, brackets, or fuel lines .

For a 1999 Accord, use the vehicle selector or catalog information on the official site to match the exact year, engine, and trim. Do not assume that a pump listed for another Accord generation will fit. Check the connector, module shape, pressure rating, and included seals before installation.

Visit: https://www.kemsoracing.com/

12. Frequently asked questions

Is the 1999 Accord fuel pump relay under the hood?

Model-specific references place the relevant PGM-FI fuel pump relay circuit in the driver-side under-dash fuse/relay box for the 1999 Accord . Check your fuse-box diagram before buying a part.

Is it called a fuel pump relay or a PGM-FI main relay?

You may see both terms. Honda service information for Accord fuel-pump circuit troubleshooting uses PGM-FI main relay 2 (FUEL PUMP) . Parts listings and forums often shorten this to main relay or fuel pump relay.

How long should the pump run when I turn the key on?

Honda’s Accord troubleshooting information says the fuel pump should run for about two seconds when the ignition is turned to ON (II) . An owner-oriented description says two to three seconds . The key point is a brief prime, not a pump that runs continuously with the engine off.

Will a bad relay set a Check Engine Light?

Not always. Cracked solder joints and intermittent power loss can come and go without a clear diagnostic code . A scan tool is useful, but circuit testing is still necessary.

Can I drive with an intermittent relay?

It is not wise. If the relay opens while the engine is running, the engine can stall in traffic. Diagnose the fault before relying on the car for commuting, highway travel, or family transport.

Why does the car restart after cooling down?

Heat causes materials inside an aging relay to expand. A cracked solder joint may separate when hot and make contact again when cool, which matches the hot no-start pattern reported on older Hondas .

Does a new relay fix every no-start?

No. Confirm the fuse, power, ground, ignition command, wiring, and fuel pressure. A battery, starter, ignition switch, ECM/PCM, immobilizer or aftermarket security device, crank sensor, ignition component, or fuel pump can be involved.

13. A short checklist you can use in the driveway

  1. Confirm the complaint: cold start, hot restart, stalling, or complete no-start.
  2. Check battery terminals and fuel level.
  3. Remove the driver’s lower dash cover.
  4. Find the under-dash fuse/relay box left of the steering column.
  5. Read the fuse-box diagram.
  6. Inspect the 15-amp PGM-FI-related fuse with a meter or test light .
  7. Turn the key to ON and listen for the relay click.
  8. Listen near the fuel filler for the two-second pump prime .
  9. Inspect the relay connector and wiring.
  10. Measure voltage and ground using the correct wiring diagram.
  11. Check for cracked solder joints if the relay is opened.
  12. Replace with an exact-match relay if testing supports it.
  13. Verify cold start, hot restart, and a road test.
  14. If pump power and ground are good but pressure is not, replace the pump with a correctly matched unit.

The location is the easy part: driver-side under-dash fuse/relay box, below and left of the steering column, behind the lower cover . The valuable part is using that location to test the circuit before spending money on a fuel pump. A careful key-on sound check, fuse check, voltage check, and hot-restart test will separate a tired relay from a failed pump on most 1999 Accords.

If the pump itself is confirmed bad, choose a correctly matched KEMSO high-performance OEM replacement with a lifetime warranty .

https://www.kemsoracing.com/