99 Honda Civic Fuel Pump Fuse: Location, Checks, and Fixes

If your 1999 Honda Civic cranks but will not start, the fuel pump fuse to check first is No. 13 FUEL PUMP, a 15A fuse in the under-dash fuse/relay box on the driver’s side. On many 1999 Civics, the under-dash label also lists this fuse as “Fuel Pump (SRS Unit),” “Engine control module relay (PGM-FI), fuel pump, airbag control module,” or a similar shared-circuit description, so the wording on your fuse-box cover may not say only “fuel pump.” The under-hood fuse box also matters: the factory workshop manual refers to an FI E/M 15A fuse in the under-hood fuse/relay box as part of PGM-FI main relay circuit checks, while a commonly published under-hood diagram for this generation lists fuse 44 as 15A for the engine control unit relay and injector control unit on non-GX models. Because labels, trim, engine, and market can change the printed assignment, use the diagram on the fuse-box cover and the owner’s or service manual for your exact VIN before replacing a fuse.

Do not install a larger fuse. Replace a blown 15A fuse only with another 15A fuse of the correct type, and find the reason it blew. A fuse that opens again right away usually means a shorted wire, damaged connector, corrosion, or a pump drawing too much current. A good fuse does not prove the pump is good. The PGM-FI main relay, the ECM/PCM control signal, wiring, ground, and the in-tank pump all have to work before fuel reaches the engine.

The quickest driveway check is the two-second prime. Honda’s 1999 Civic workshop manual says the ECM/PCM grounds the PGM-FI main relay for about two seconds when the ignition is first turned to ON (II), which sends current to the fuel pump to pressurize the system. When the engine is running, the ECM/PCM keeps the relay energized; when the engine is not running and the ignition is on, it cuts the ground and stops pump current. In a quiet place, turn the key to ON without cranking. With the fuel filler cap removed, Honda’s manual says you may hear pump noise from the filler port for about two seconds. No sound is a reason to test the fuse, relay, wiring, and pump, not an automatic reason to buy a pump.

This guide is written for U.S.-market 1999 Civic sedans, coupes, and hatchbacks with the original fuel-injected gasoline engine. It covers the common DX, LX, EX, Si, HX, GX-related differences where published diagrams are clear, and value-package cars where service information is available. If the car has an engine swap, an aftermarket immobilizer, a remote start, a rewired pump, or a non-original harness, the factory color codes and fuse assignments may no longer match. Start with the fuse-box cover, then a year-specific factory wiring diagram.


1. The short answer: what to check first

1. Check No. 13 FUEL PUMP, 15A, in the under-dash fuse/relay box. The driver-side under-dash fuse box is at the bottom of the instrument panel. Remove the cover to see the fuses. A published 1999 Civic under-dash diagram lists fuse 13 as 15A for “Engine control module relay (PGM-FI), fuel pump, airbag control module.” A 1999 Civic Coupe fuse reference lists No. 13 as a 15A MINI fuse described as “Fuel Pump (SRS Unit).” The 1999 workshop manual also calls it “No. 13 FUEL PUMP (15 A)” in the under-dash fuse/relay box and includes it in PGM-FI circuit troubleshooting.

2. Check the FI E/M, 15A, in the under-hood fuse/relay box. The workshop manual’s PGM-FI main relay checks include inspecting the FI E/M 15A fuse in the under-hood fuse/relay box and repairing a short in the wire between that fuse and the PGM-FI main relay if needed. A widely published fuse diagram for the 1994–2000 Civic generation identifies the under-hood 15A fuse 44 on non-GX cars as protecting the engine control unit relay and injector control unit; the same source lists a 20A rating for GX. Use your own cover labeling or factory manual to match the name and number.

3. Listen for the two-second pump prime. The factory test says the fuel pump should run for two seconds when the ignition is first turned ON (II). The manual also says that if the engine starts and continues to run, the PGM-FI main relay is OK. If the pump primes and the engine runs, the fuse and relay are doing their basic job, even if another driveability problem still exists.

4. If the fuse is blown, fix the cause before repeating the test. Common causes listed for a 1999 Civic fuel pump fuse include damaged or exposed wiring touching the body, a failing pump drawing excessive current, a badly clogged fuel filter making the pump work harder, or a fuse with the wrong lower amperage installed. Keep the repair orderly: inspect visible wiring, connectors, and the under-rear-seat access area before condemning the pump.

5. Do not confuse the fuse with the relay. The PGM-FI main relay is not a fuse. Honda’s 1996–2000 Civic service information describes it as two individual relays in one unit. One relay supplies battery voltage to the ECM/PCM, injectors, and the second relay when the ignition is on. The second relay powers the fuel pump for two seconds at key-on and while the engine is running. A relay can click and still have burned contacts, cracked solder joints, or an open internal circuit.


2. Where the 1999 Civic fuel pump fuse is located

The under-dash fuse/relay box is at the bottom of the instrument panel on the driver’s side, and the cover must be removed for access. On a left-hand-drive U.S. car, sit in the driver’s seat and look low near the left kick panel below the steering column. You may need to move the seat back, use a flashlight, and kneel outside the car with the door open. On some cars, a lower dash panel or storage pocket makes the fuse labels hard to read. Do not pull hard on wires or pry against plastic tabs with a metal screwdriver.

Use the printed diagram on the cover as your final map for fuse position. Published fused diagrams can group several protected systems under one fuse. For example, fuse 13 may be shown with the PGM-FI relay, fuel pump, and SRS unit on the same line. That does not mean the fuse directly powers every part in the same way; it means the circuit protection covers a shared power feed. A VIN-specific Honda owner’s manual, the fuse-box cover, or the factory workshop manual is the best source when a previous owner has replaced the cover or installed an aftermarket fuse panel.

The under-hood fuse/relay box is near the battery. A published 1999 Civic diagram places the engine-compartment fuse and relay box next to the battery and says to push the tab to open it. Another generation diagram says the main under-hood box is next to the battery, with an additional ABS box on some cars. The 1999 workshop manual identifies the relevant under-hood protection as the FI E/M 15A fuse during PGM-FI main relay checks.

The fuel pump itself is inside the fuel tank, accessed from under the rear seat cushion. Honda’s 1999 Civic workshop fuel pump test says to remove the seat cushion, remove the floor access panel, and disconnect the fuel tank 2P connector with the ignition OFF. A practical owner-level replacement guide gives the same layout: lift the rear seat bottom, remove the access panel, and inspect the electrical connector on top of the pump assembly. You do not normally need to drop the tank on this model, although rust, damaged fasteners, or previous repairs can make a simple job harder.


3. What the fuse actually protects

Fuse 13 is a 15A protection point in the ignition-fed side of the fuel pump/PGM-FI system; it is not a test of fuel pressure. The workshop manual’s PGM-FI circuit troubleshooting checks for battery voltage at the PGM-FI main relay 7P connector terminal No. 5 with the ignition ON. If voltage is missing, the manual says to repair an open or short in the wire between the relay and the No. 13 FUEL PUMP 15A fuse, or replace that fuse. That is why a fuse can look fine while a wiring fault between the fuse box and relay still stops the pump.

The under-hood FI E/M 15A fuse is part of the battery-feed side. In the same factory circuit test, the manual checks battery voltage between PGM-FI main relay terminal No. 7 and body ground. If voltage is missing, it calls for checking the wire between the relay and the FI E/M 15A fuse, then replacing that fuse if needed. Think of the system as two power paths plus a control path: constant battery feed, ignition-switched feed, and ECM/PCM control and ground. A problem in any one can create a no-start.

The ECM/PCM controls the pump through the PGM-FI main relay. Honda’s workshop manual says the ECM/PCM supplies ground to the relay for two seconds at initial key-on to pressurize the fuel system, keeps the pump powered while the engine runs, and cuts ground when the engine is not running with the ignition on. The factory PGM-FI main relay description says the relay contains two internal relays: one supplies voltage to the ECM/PCM, injectors, and the second relay; the second supplies the fuel pump. This is why a no-start can involve a relay that also affects the engine computer and injectors, not only a humming pump in the tank.

A shared label can confuse parts-store lookups. If a label reads “Fuel Pump (SRS Unit)” or includes the airbag control module, do not assume the SRS system is causing your no-start. Published 1999 Civic fuse references show shared descriptions for fuse 13. Check the circuit with a meter rather than replacing unrelated SRS components. Airbag systems also require special safety procedures; do not probe yellow SRS connectors while diagnosing a fuel pump fuse.


4. Tools that make the job easier and safer

1. A digital multimeter. A test light can show that voltage exists, but a multimeter lets you check continuity, battery voltage, ground quality, and an open fuse. The factory procedure uses voltage-to-ground and continuity checks at the PGM-FI main relay connector and the fuel tank connector.

2. A fuse puller or needle-nose pliers with insulated handles. Mini blade fuses can be tight after decades of heat cycling. Pull straight out; do not rock the fuse hard enough to crack the socket.

3. Correct replacement fuses. Keep spare 15A mini fuses in the car. Also keep the other ratings shown on your cover, but never substitute a higher amperage to “get home.”

4. A flashlight, inspection mirror, and phone camera. The under-dash area is cramped. Photograph the fuse box before removing anything so you can restore positions if a label is faded.

5. Basic hand tools for the rear access panel. Honda’s fuel pump test and replacement sections call for removing the rear seat cushion and floor access panel, then disconnecting the fuel tank 2P connector. A practical DIY guide lists a small socket set, screwdrivers, clean rags, gloves, safety glasses, and a container for small fuel spills.

6. Safety equipment. Work outdoors or in a well-ventilated area. Honda’s manual says not to smoke during fuel pump testing or replacement and to keep open flames away from the work area. A practical guide also recommends disconnecting the negative battery cable and having a fire extinguisher nearby. Keep sparks, incandescent drop lights, heaters, and running space heaters away from fuel vapors.


5. How to check the fuse the right way

1. Park safely and turn the ignition OFF. Set the parking brake, put an automatic transmission in Park or a manual in Neutral, and remove the key. Let the car sit if the engine is hot.

2. Find the driver-side under-dash fuse box. Remove the cover. Compare the diagram with the fuse layout. Look for No. 13, 15A, FUEL PUMP or the shared PGM-FI/fuel pump/SRS description.

3. Pull the fuse and inspect it. A blade fuse has a visible metal strip between the two blades. A clean break, dark burn mark, or melted plastic means it opened. Do not rely only on appearance; a hairline break can be hard to see.

4. Confirm with a continuity test. With the fuse removed, measure across the two exposed top test points or blades. Low resistance confirms continuity. No continuity means the fuse is open. If the fuse is installed and the car has power, a voltage check on both test points to a known good ground should show voltage on both sides. Voltage on only one side means the fuse is open.

5. Check the fuse socket. Look for green or white corrosion, a loose terminal, melted plastic, or a blade that fits loosely. Honda’s factory troubleshooting notes include checking for loose FI E/M and No. 13 fuses when an intermittent fault is present. A loose fuse can cause an intermittent no-start that disappears after you touch the box.

6. Replace only with the specified 15A rating. Press it fully into place. Turn the key to ON and listen for the two-second prime. Do not crank repeatedly with a blown fuse or a dry fuel system.

7. If the new fuse blows, stop. A repeated open fuse means current is going somewhere it should not. A 1999 Civic fuse reference lists shorted wiring, a damaged pump, a severely clogged fuel filter, or an incorrect lower-rated fuse as common causes. Have the harness and pump current draw checked with the correct wiring diagram and an ammeter or current clamp.


6. If the fuse is good but the engine still will not start

1. Listen for the two-second prime. Honda says the pump should run for about two seconds when the ignition is first turned ON (II). The manual suggests removing the fuel fill cap and listening near the fuel fill port. Road noise, a loud fuel pump on another vehicle, or a noisy cabin fan can hide the sound. Turn off the radio and blower first.

2. Watch the check engine light behavior. Honda’s 1999 workshop material connects EFI power checks with the MIL and lists loose FI E/M, No. 13 FUEL PUMP, and meter fuses as possible intermittent-fault checks. If the dash gives no normal key-on bulb check, include the ECM/PCM power feeds in your diagnosis.

3. Check the PGM-FI main relay. The factory description says the unit contains two relays and is located at the right side of the cowl. Some owner-level guides describe finding it near the driver-side under-dash fuse box or behind the glove box, and those descriptions vary by source and market. Use the Honda service manual location and connector identification for your car instead of guessing from a generic photo.

4. Use the relay’s behavior as a clue. A common Honda failure pattern is an intermittent crank/no-start, often after heat soak, with no pump prime. A relay-focused guide lists cranking with no start, stalling when hot, no priming sound, and an engine that starts then dies as common symptoms. The Honda manual gives a simple rule: if the engine starts and continues to run, the PGM-FI main relay is OK.

5. Test voltage at the relay connector. The factory circuit check calls for battery voltage between relay terminal No. 7 and body ground, battery voltage at terminal No. 5 with ignition ON, and a starter-signal voltage check at terminal No. 2 in START (III). It also includes a ground continuity check at terminal No. 3. If you do not have the correct connector view and terminal numbering, do not probe random terminals. A wrong meter probe can damage the ECM/PCM.

6. Check the pump connector under the rear seat. Honda’s test says to remove the seat cushion and access panel, make sure the ignition is OFF, disconnect the fuel tank 2P connector, and use a jumper at PGM-FI main relay 7P connector terminals No. 4 and No. 5 for the specified test. With the ignition ON, the manual checks for battery voltage between fuel pump connector terminal No. 1 and body ground. If voltage is present and the pump ground is OK, the manual says to replace the fuel pump; if voltage is absent, check the harness. Because this test bypasses normal relay control and involves fuel-system connectors, it is best performed by someone comfortable with factory wiring diagrams and fuel-vapor safety.

7. Do not skip the ground. The factory test specifically says that when battery voltage is available at the pump connector, check the fuel pump ground; if the ground is good, replace the pump. A pump with power but a bad ground will not run.


7. What a blown fuse is telling you

1. A short to body ground. Damaged, frayed, or exposed wiring can touch metal and open the fuse. On an older Civic, check areas where someone may have installed an alarm, stereo amplifier, remote start, aftermarket pump, or engine-swap harness. Look along the rear seat access panel, under trim, near sharp metal edges, and around connectors that have been spliced.

2. A pump drawing too much current. A failing pump near the end of its life may pull more current than normal and overload the fuse. A pump that whines loudly, loses power under load, or causes repeated fuse failures deserves a current-draw and fuel-pressure check. A practical replacement guide lists cranking with no start, no prime sound, sputtering or stalling, loss of power under load, and surging or hesitation among common failing-pump symptoms.

3. A restricted filter or line. A severely clogged fuel filter can make the pump work harder, increasing current draw and opening the fuse. Replace the filter on schedule and use a part that fits the 1999 Civic’s fuel system. Do not assume every aftermarket fuel line or filter is compatible with E10 fuel commonly sold in the United States.

4. The wrong fuse rating. A fuse with a lower rating than Honda specified can open during normal operation. A fuse with a higher rating is worse: it can allow wiring to overheat before the fuse opens.

5. Corrosion and poor connections. Moisture, a leaking windshield or sunroof drain, or a damp cabin can affect an under-dash box. A relay guide lists corrosion at relay terminals, overheating from excessive pump current, age, and physical damage as common relay failure causes. Clean only with products safe for electrical contacts, and disconnect the battery first.

6. Repeated fuse failure after pump replacement. Check the new pump’s connector, harness routing, strainer, tank debris, and the lock-ring seal. A pinched wire under the access panel or a connector not fully seated can create an intermittent fault. If the fuse still opens, have a professional measure current draw and inspect the full circuit.


8. Common symptoms and what they usually mean

1. Engine cranks normally, never fires. This can be a blown No. 13 fuse, a PGM-FI main relay fault, no ECM/PCM control, a wiring break, a bad ground, or a dead pump. Check the two-second prime before ordering parts.

2. Starts cold, refuses to restart hot. Relay trouble is a well-known pattern on older Hondas, and a relay guide lists hot-weather intermittent stalling and no-start among common symptoms. A failing pump can also act up with heat, so confirm power and ground at the pump during the failure.

3. Starts, then dies after a few seconds. The initial prime may occur, but power may not continue once the engine should be running. The ECM/PCM is supposed to keep the relay energized while the engine runs. Check relay control, ignition feeds, and crank/cam-related inputs with a scan tool or factory procedure.

4. No prime sound, but the fuse is good. Move to the FI E/M fuse, PGM-FI relay terminals, ignition switch feed, starter signal, ECM/PCM control, harness, and pump connector. This is where a multimeter and wiring diagram save money.

5. Pump runs, but the engine hesitates or loses power under load. The electrical feed may be fine while fuel pressure or volume is low. A weak pump, clogged filter, restricted line, or faulty pressure regulator may be involved. A fuel pressure gauge and a pressure specification from the factory manual are needed for a firm diagnosis.

6. Fuse blows immediately after replacement. Stop installing fuses. Find the short or excessive current draw. Repeatedly cycling fuses can heat a harness and turn a small repair into a larger one.

7. Check engine light with fuel-related codes. A code points to a circuit or pressure condition; it does not by itself name the failed part. A DIY guide lists P0230 for a fuel pump primary circuit malfunction and P0087 for fuel rail pressure too low, but code availability and definitions should be checked against the 1999 Civic’s OBD-II system and a live scan tool. Record freeze-frame data before clearing anything.


9. Step-by-step driveway diagnostic plan

1. Confirm the complaint. Note whether the starter cranks at normal speed, whether the check engine light comes on at key-on, whether the pump primes, whether the fuel gauge shows fuel, and whether the problem happens cold, hot, or after rain. A low fuel level can make pump noise harder to hear and can stress an older in-tank pump.

2. Inspect both fuse boxes. Check No. 13 FUEL PUMP 15A under the dash and the FI E/M 15A under the hood. On a published non-GX diagram, under-hood fuse 44 is 15A for the PGM-FI/injector control circuit; on GX it is listed as 20A. Match your own cover.

3. Verify battery condition. A weak battery can crank slowly and confuse ECM/PCM voltage checks. Charge or test the battery before deep electrical diagnosis.

4. Test fuses with a meter, not just your eyes. Check continuity out of the car and voltage on both sides in the car. Wiggle the fuse gently to find a loose socket, but do not force it.

5. Perform the key-on prime test. Turn ON (II), listen for about two seconds, turn OFF, and repeat once after a short pause. If the pump runs, do not assume fuel pressure is correct; it only confirms basic electrical operation.

6. If there is no prime, check the PGM-FI main relay circuit. Use the factory 7P connector terminal checks for battery feed, ignition feed, starter signal, ground, and ECM/PCM control. Relay bench testing in the Honda manual checks continuity across specific terminal pairs with battery voltage applied. Do not use a generic four-pin relay pin chart on a seven-terminal Honda main relay.

7. Inspect the rear seat access area only when ready to work safely. Remove the seat cushion and access panel. Look for a loose 2P connector, corrosion, damaged insulation, signs of previous splicing, or a fuel smell. If you smell raw gasoline, see wet fuel, or find brittle wiring, stop and get professional help.

8. Confirm power and ground at the pump during the failure. Honda’s manual provides a controlled jumper test at the relay connector and a voltage check at the fuel tank 2P connector. If voltage and ground are correct and the pump does not run, the pump is the factory manual’s stated replacement conclusion.

9. After any repair, cycle the key two or three times and check for leaks. Honda’s fuel-system service text says that after turning the ignition ON, the pump runs about two seconds and fuel pressure rises; it instructs repeating that two or three times and checking for fuel leakage. Do this before starting the engine.


10. Replacing the fuse box parts and relay without creating new problems

1. Disconnect the negative battery cable before unplugging the PGM-FI main relay or working at the pump connector. A practical Civic replacement guide recommends this to prevent shorts or accidental sparks. Reconnect only after all connectors and covers are back in place.

2. Match the relay exactly. Use the Honda part number or a reputable cross-reference for your VIN. A relay guide lists Honda part number 39510-S04-952 for a 1999 Civic application, but verify with a dealer or trusted parts catalog before ordering. Do not swap in a relay with a different pin layout or rating.

3. Do not assume a click equals a good relay. A guide recommends bench testing for coil resistance and switch continuity, or substitution with a known-good relay of the same rating. Honda’s manual uses specific terminal-pair continuity checks. Cracked solder joints can make a relay intermittent even when it clicks.

4. Keep the fuse cover installed. It protects the terminals from dirt and moisture and carries the circuit map. If the diagram is missing, photograph a verified year-specific diagram and keep it with your maintenance records.

5. Label any replaced fuse with its rating. Write the date and mileage on a small maintenance card. If the same fuse opens again, you will know quickly that the first repair did not address the cause.


11. When the fuel pump itself needs replacement

A pump replacement is justified when the fuse and relay circuits test good, power and ground reach the pump, and the pump still does not run or cannot supply correct pressure and flow. Honda’s factory test says that if battery voltage is available at the pump connector and the ground is OK, replace the fuel pump. A practical owner guide also advises checking the fuse and main relay first because the relay is a common failure point and many owners replace a pump unnecessarily.

Access on a 1999 Civic is through the rear seat. Honda’s replacement section lists removing the seat cushion, removing the floor access panel, disconnecting the 2P connector, removing the pump mounting nuts, and lifting the pump from the tank. A DIY guide describes lifting the front edge of the rear seat cushion to release two clips, then removing the access panel screws. Clean the top of the pump area before opening the tank so dirt does not fall inside.

Relieve pressure and control fuel safely. A practical guide describes removing fuse 13, starting the engine until it stalls, cranking briefly, then disconnecting the negative battery cable. Honda’s manual gives explicit no-smoking and no-open-flame warnings for fuel pump testing and replacement. Have rags ready for small spills; do not use a shop vacuum around fuel vapors.

Replace related wear items. A KEMSO diagnostic guide recommends replacing the pump and strainer together, renewing an accessible in-tank filter, replacing the external filter when applicable, and addressing cracked hoses or a tired tank seal. Consider a new fuel pump relay as inexpensive preventive maintenance if the original has heat-related intermittent behavior.

Prime and inspect before driving. Reconnect the battery, cycle the ignition ON two or three times, and check every connection for wetness or odor. Then start the engine and let it idle while you recheck the access area. Do not close the panel until you are sure there is no leak.

A shop is the right choice when the fuse keeps blowing, the tank is rusty, the connector is melted, the harness has been modified, or fuel is visible. A fuel-system troubleshooting guide says to stop and call a professional if you smell raw fuel, see a wet tank seam, or find brittle harness insulation, because jumper testing near leaks is a fire risk. It is also sensible to hand the job to a technician if you do not have a wiring diagram, a multimeter, or a safe workspace.


12. Parts and fitment notes for U.S. owners

1. Confirm trim and engine before ordering. The 1999 Civic came in multiple body styles and engine families in the U.S. Published fuse references show a 15A under-hood fuse 44 for non-GX cars and 20A for GX in one generation diagram. That difference is a good reason to check your VIN rather than buying from a generic “96–00 Civic” listing.

2. Use the fuse-box cover and a factory manual for circuit names. One published 1999 diagram calls under-dash fuse 13 “Engine control module relay (PGM-FI), fuel pump, airbag control module,” while another coupe reference says “Fuel Pump (SRS Unit).” Both point to the same 15A No. 13 fuse. The Honda workshop manual uses “No. 13 FUEL PUMP (15 A).”

3. Buy fuses from a reputable auto-parts source. Cheap, unmarked fuses can have inconsistent ratings. Keep a small assortment in the glovebox, but mark the 15A slot clearly.

4. Check the fuel filter service history. A clogged filter is listed as a possible reason a 1999 Civic fuel pump fuse blows because it can make the pump work harder. If the car has an unknown maintenance history, filter replacement is a sensible part of a full fuel-system service.

5. Keep the tank above one-quarter full when practical. A KEMSO guide notes that fuel helps cool and lubricate an in-tank pump and that repeatedly running low can contribute to shorter life. This is especially useful advice for an older daily driver with the original tank sending unit.

6. Document what you tested. Write down fuse continuity, voltage readings, whether the pump primed, and the conditions during the no-start. This helps a mechanic avoid repeating your work and helps you spot an intermittent pattern.


13. Frequently asked questions

1. Is the 1999 Honda Civic fuel pump fuse under the hood or under the dash?
The main fuse owners usually mean is No. 13 FUEL PUMP, 15A, in the under-dash fuse/relay box on the driver’s side. The under-hood box also has an FI E/M 15A fuse involved in the PGM-FI main relay circuit. Check both.

2. What size is the fuel pump fuse?
15A for No. 13 in the under-dash box. The under-hood FI E/M fuse in the workshop manual is also 15A. Do not increase either rating.

3. Why does my fuse label mention SRS?
Some published 1999 Civic references list fuse 13 as “Fuel Pump (SRS Unit)” or include the airbag control module in the same line. It is a shared circuit description. Do not probe SRS wiring while chasing a pump problem.

4. Will a bad fuel pump fuse cause stalling while driving?
An open fuse will stop power to the circuit it protects, but intermittent stalling can also come from a loose fuse, failing PGM-FI main relay, wiring fault, ECM/PCM power issue, or weak pump. Honda’s troubleshooting notes include loose FI E/M and No. 13 fuses among intermittent-fault checks.

5. How long should the pump run at key-on?
About two seconds. Honda’s 1999 Civic manual says the ECM/PCM energizes the PGM-FI relay for two seconds at initial key-on to pressurize the system and keeps the pump powered while the engine runs.

6. Can I bypass the relay to test the pump?
Honda’s manual includes a specific jumper test at the PGM-FI main relay 7P connector terminals No. 4 and No. 5, followed by a voltage check at the fuel tank connector. Only use the factory procedure, correct terminal view, and full fuel-vapor precautions. Do not run a loose wire from the battery to the pump.

7. The fuse is good and I hear a click. Is the relay fine?
Not necessarily. Listen for the pump prime as well. A relay can click with damaged contacts, and the factory manual uses terminal-pair continuity checks for a firm relay test. Also check the FI E/M feed, No. 13 ignition feed, ground, and ECM/PCM control.

8. Can I drive with an intermittent no-start?
It is risky. If the car stalls in traffic, you lose power steering assist and may be stranded. Repair the cause before relying on the car for commuting.

9. Does a new pump fix a blown fuse?
Only if the old pump was drawing excessive current and all wiring is sound. A shorted harness, clogged filter, wrong fuse rating, or poor connector can still open the new fuse. Diagnose first.

10. Where is the fuel pump on this Civic?
Inside the fuel tank, accessed through a panel under the rear seat cushion. You normally do not drop the tank.


14. Recommended replacement fuel pump: KEMSO

If testing proves the pump is the failed part, we recommend buying a KEMSO brand Fuel Pump. KEMSO Fuel Pump products are described as high-performance, OEM Replacement units, and the brand supports them with a lifetime warranty. Brand material also says KEMSO pumps are engineered for consistent fuel pressure and flow and are built as direct replacements with the installation items needed for many applications. For an older 1999 Civic, confirm the exact year, body style, engine, and connector style before ordering; a correct diagnosis and correct fitment matter more than a higher-flow number.

Visit the official KEMSO website at https://www.kemsoracing.com/ to browse the fuel pump catalog, confirm fitment for your Civic, review warranty terms, and contact the brand with your VIN or part number if you need help choosing the right pump. Keep your test notes, old part number, and photos of the pump connector handy when you order. If the original fuse blew repeatedly, finish the wiring and filter checks before installing any new pump.


15. Final checklist before you put the car back on the road

1. No. 13 FUEL PUMP 15A is installed, fully seated, and continuous.

2. The under-hood FI E/M 15A feed is good and matches your cover or factory diagram.

3. The PGM-FI main relay clicks, passes the specified continuity checks, and keeps the engine running.

4. The pump primes for about two seconds at initial key-on.

5. The rear access panel connector is clean, tight, and routed away from sharp edges.

6. The engine starts, idles, accelerates, and does not stall after a hot restart.

7. There is no fuel odor, wetness, or leak after several key cycles.

8. The fuse box cover, rear access panel, and seat cushion are secured.

9. Your maintenance record lists the date, mileage, parts used, and readings taken.

10. If the same fuse opens again, stop driving and have the circuit tested professionally.


A 1999 Civic is old enough that previous repairs can matter as much as the factory diagram. Start with the simple checks, verify voltage and ground, and replace only what the evidence supports. That approach usually saves a fuel pump, a tow bill, and a weekend of guessing.

KEMSO official website: https://www.kemsoracing.com/