99 Honda CRV Fuel Pump Relay Location: Find It Fast

The short answer: On a U.S.-market 1999 Honda CR-V, there is not a separate, standalone "fuel pump relay" sitting in the under-hood fuse box. Fuel pump power is controlled by the PGM-FI main relay, a 7-pin relay that contains two internal relays in one case. On left-hand-drive U.S. models, factory service information places it at the passenger-side cowl, under the right side of the dash, behind or near the glove box, mounted on a bracket. One internal relay feeds the ECM/PCM and fuel injectors; the second one powers the fuel pump for about two seconds at key-on and then keeps it powered while the engine is running. The under-dash fuse/relay box on the driver's side is a different assembly; the under-hood box handles items such as the A/C compressor, radiator fan, condenser fan, and ABS pump motor relay. Some online answers say "left kick panel" for Hondas in general, and a few aftermarket articles describe the 1999 CR-V relay as being in the driver-side fuse box. Those descriptions do not match the 1999 CR-V factory manual or wiring-location charts, so start at the passenger side and verify by connector shape, bracket, and the two-second click. If your CR-V cranks but will not start, check the fuses, listen for the two-second pump prime, test the PGM-FI main relay, and check power and ground at the pump before buying a new pump.

This guide is written for the 1997–2001 first-generation CR-V sold in the United States, with emphasis on the 1999 model year. Right-hand-drive import models, engine swaps, and modified wiring can place the relay on the opposite side, so use the VIN, factory manual, and the actual connector in your vehicle as the final authority.


1. What the 1999 CR-V Actually Uses

Honda's service manual calls the part the PGM-FI main relay. It is not a simple four-pin cube that you pull from a row of identical relays under the hood. The case houses two separate electromagnetic switches:

  1. The first internal relay turns on with the ignition switch. It supplies battery voltage to the ECM/PCM, powers the fuel injectors, and supplies power to the second internal relay.
  2. The second internal relay is energized for roughly two seconds when you turn the key to ON (II). It sends battery voltage to the fuel pump. Once the engine is running, the PCM keeps that relay energized so the pump continues to deliver fuel.

That two-relay design explains a lot of confusing no-start symptoms. A failure can interrupt the ECM/PCM power, the injector power, the fuel pump power, or more than one of these at the same time. It also explains why parts catalogs may list the component as a "main relay," "PGM-FI relay," "fuel injection main relay," or "fuel pump relay," even though there is one physical unit.

Common replacement listings for 1997–2001 CR-V models describe a 7-pin Mitsuba-style relay with a bracket, often with part references such as RZ-0132 or RZ-0159. The 1999 service manual connector chart identifies a 7-cavity connector under the right side of the dash for the PGM-FI main relay, which is a useful detail when you are looking up at the wiring harness with a flashlight.

Why people get the location wrong:

  1. Many older Hondas and Acuras use a main relay near the driver-side footwell, so generic advice gets copied onto CR-V pages.
  2. The CR-V has a driver-side under-dash fuse box, which invites the assumption that every interior relay is plugged into it.
  3. A search result may show a modern relay layout or a different generation of CR-V.
  4. Aftermarket part descriptions sometimes call the PGM-FI relay a "fuel pump relay," which leads owners to look for a small plug-in relay under the hood.

For a 1999 U.S. CR-V, the most reliable starting point is the right side of the dash near the passenger cowl, not the engine-bay relay center.


2. Exact Location on a U.S. Left-Hand-Drive 1999 CR-V

Here is how to orient yourself before removing trim:

  1. Sit in the passenger seat and look toward the footwell. The area you want is high up and forward, near the right-side cowl and the lower dash structure.
  2. Move the passenger seat all the way back. Put a bright flashlight or headlamp on the floor aimed upward.
  3. Look under the right side of the dash, behind the glove box area. The relay is typically above the passenger lower cover, attached to a metal bracket or secured near the harness.
  4. Expect a rectangular plastic case with a multi-pin connector. Factory service material describes a 7-pin connector for the PGM-FI main relay under the right side of the dash.
  5. The driver-side interior fuse/relay box is below the instrument panel near the left kick panel. You may need it for fuse checks, but it is not the primary location of the PGM-FI main relay on this model.

A practical way to confirm you have the right part is the key-on click test. Turn the ignition from OFF to ON without cranking. The relay should click, and the fuel pump should run for about two seconds. Put a finger lightly on the suspected relay while a helper turns the key. A click or a small movement you can feel helps separate it from nearby relays and modules. The 1999 service manual also says that if the engine starts and continues to run, the PGM-FI main relay is functioning in that moment, although an intermittent fault can still return when hot.

Do not confuse it with these parts:

  1. Under-hood fuse/relay box: Contains relays for the A/C compressor clutch, blower motor, condenser fan, radiator fan, and ABS pump motor on 1999 wiring charts.
  2. Under-dash fuse/relay box: Located under the driver's side of the instrument panel on left-hand-drive first-generation CR-Vs. It carries many fuses and some relays, including the power window relay.
  3. Fuel pump itself: The 1999 CR-V uses an electric in-tank pump. Honda provides an access panel under the rear seat area, reached after folding the left rear seat cushion forward and removing the base frame cover and floor access panel.
  4. Fuel pump 5P connector: This is at the pump/tank area, not at the dash relay. The factory fuel-pump test procedure calls for disconnecting this connector after removing the access panel.

3. Symptoms That Point to the PGM-FI Main Relay

A failing main relay on late-1990s Hondas is well known for intermittent crank/no-start complaints. Heat is a common trigger. The vehicle may start cold, stall after a short stop, and restart after it cools down. Cracked solder joints inside the relay case are a documented failure pattern on this era of Honda/Acura main relays.

Watch for these signs:

  1. Engine cranks normally but does not fire. The starter sounds healthy, but the pump does not prime.
  2. No two-second hum from the fuel tank. With the fuel filler cap removed, Honda's manual says you should hear pump noise for about two seconds at key-on when you listen at the filler port.
  3. No normal relay click at key-on. A missing click from the right side of the dash is a strong clue, though road noise and a weak battery can make listening unreliable.
  4. Check engine light behaves oddly at key-on. A main-relay diagnostic guide lists no two-second bulb check as one of the signs, because the relay also supplies ECM/PCM power.
  5. Stalling while driving or after warm-up. Power to the ECM, injectors, or pump can drop out as the relay heats up.
  6. The problem changes with temperature. Hot days, a heat-soaked cabin, or a restart after a quick errand are classic conditions.
  7. The car restarts after sitting. This does not prove the pump is good; it only shows that the circuit worked again after cooling.

These symptoms are not exclusive to the relay. A weak battery, corroded battery terminals, poor grounds, a blown fuse, damaged wiring, a clogged fuel filter, a bad pump connector, or a worn fuel pump can look similar. That is why the order of testing matters.


4. Tools and Supplies That Make the Job Easier

You do not need a full shop to narrow this down. Gather:

  1. Owner's manual and a repair manual or wiring diagram for the 1999 CR-V. Use the fuse legend and connector views for your exact trim.
  2. A bright flashlight or headlamp. The relay is tucked high under the dash.
  3. A small inspection mirror. Helpful for reading the part label without removing half the dash.
  4. A digital multimeter. Needed to check battery voltage, fuse continuity, power at the pump connector, and ground.
  5. A basic OBD-II scan tool. Even if the check engine light is off, stored codes or live data can point toward crank sensors, immobilizer faults, or other no-start causes.
  6. Trim tools and a small ratchet with 10 mm socket. Useful for lower dash covers, the glove box area, and battery service.
  7. Nitrile gloves, safety glasses, and a fire extinguisher rated for flammable-liquid fires. Any fuel-system work deserves that setup.
  8. A helper. One person turns the key while the other listens at the fuel filler or feels for the relay click.
  9. A phone camera. Take a photo of the bracket, connector, and wire routing before unplugging anything.

If you plan to test fuel pressure, use a gauge and adapter set that fits the Honda fuel system and follow the factory service procedure. Do not loosen fuel lines based on a guess. Gasoline vapor is hazardous, and a small mistake can cause injury or fire.


5. Step-by-Step: Find and Confirm the Relay

Follow this sequence in order. It keeps the simple checks first and avoids buying parts you do not need.

1. Verify the battery and starting system first

  1. Check that the headlights are bright and the starter cranks at normal speed.
  2. Inspect both battery terminals, the negative cable to the body, and the engine/transmission ground straps. A battery can show acceptable open-circuit voltage and still fail under load through dirty connections.
  3. If the starter is slow, fix that first. Low system voltage can make relays chatter and make the pump sound weak.

2. Check the relevant fuses

  1. Locate the driver-side under-dash fuse/relay box and use the cover legend or owner's manual.
  2. Inspect the fuses associated with the fuel pump, PGM-FI, ECM/PCM, and ignition circuits. Fuse numbering and labels can vary by trim and by which diagram you read, so rely on the label for your vehicle rather than a generic position number.
  3. Test each fuse with a meter or test light on both sides, not just by looking at it. A hairline crack can be hard to see.
  4. If a fuse is blown, replace it once with the same amperage. If it blows again, stop and find the short. Never install a higher-amp fuse.

3. Listen for the two-second prime

  1. Switch off accessories so the cabin is quiet.
  2. Remove the fuel filler cap.
  3. Have a helper turn the key to ON (II) without cranking while you listen at the filler opening.
  4. Honda's 1999 service procedure says the pump should run for about two seconds and make noise you can hear at the filler port.
  5. Repeat after turning the key off for at least ten seconds. Some systems will not repeat the prime exactly the same way if the key is cycled too quickly.

If you hear the hum: The pump is getting power at that moment. The relay may still be intermittent, but you should move on to fuel pressure, filter condition, spark, and scan data before condemning the relay.

If you hear nothing: Continue with the relay, wiring, and pump-power checks. Silence alone does not prove the pump is bad.

4. Locate the click under the right side of the dash

  1. Move the passenger seat back and place a flashlight on the floor pointing up.
  2. Reach under the right side of the dash near the cowl and glove box.
  3. Touch the suspected rectangular relay lightly while a helper turns the key ON.
  4. You should hear and feel a click. A second click may follow as the two internal relays operate.
  5. Use a mirror to confirm a multi-pin connector and a bracket. Do not yank on wires.

If you cannot reach it comfortably, remove the passenger-side lower dash cover or the glove box as described in a model-specific repair manual. Support the cover and watch for wiring to accessories, the blower motor, and the passenger airbag. Do not probe yellow SRS connectors. If airbag wiring is in your way, stop and use the factory procedure.

5. Identify the part before ordering

  1. Read the label on the relay case.
  2. Count the terminals or compare the connector to a known 7-pin PGM-FI main relay listing for 1997–2001 CR-V.
  3. Compare the bracket shape, connector shape, and part number with the replacement.
  4. Buy a relay that matches the original pin configuration and mounting. A cheap universal relay with the wrong pinout can damage the circuit or leave you stranded.

6. How to Test Before Replacing Parts

A no-start on a 26-year-old SUV is rarely a one-part decision. Use this practical order.

1. Test the relay circuit with a multimeter

  1. Back-probe the connector carefully; do not pierce insulation unless the factory procedure calls for it.
  2. Confirm battery voltage on the constant-power terminal with the key off.
  3. Confirm switched ignition voltage with the key on.
  4. Confirm that the PCM provides the control ground during the two-second prime and while the engine runs. The factory description says the first internal relay feeds the ECM/PCM and injectors, while the second supplies the pump for two seconds at key-on and continuously with the engine running.
  5. Check the relay's ground and the ground points in the harness. A poor ground can produce the same result as a dead relay.
  6. If power and control are present at the relay but there is no output to the pump circuit, the relay is suspect.

A relay bench test is also possible, but follow the pin diagram printed on the case or supplied with the replacement. Do not apply 12 volts across random terminals.

2. Use the factory-style pump check

Honda's 1999 fuel-pump test gives a clear path: fold the left rear seat cushion forward, remove the base frame cover, remove the floor access panel, switch the ignition OFF, and disconnect the fuel pump 5P connector. From there, the factory procedure uses a jumper at the PGM-FI main relay 7P connector to determine whether the pump itself runs. Because that test involves applying power in a specific circuit, use the actual service manual page for your VIN and trim, not a shortened forum version.

A safer home-level version is to check for:

  1. Battery voltage at the pump connector during the two-second prime.
  2. Continuity and low resistance on the pump ground circuit.
  3. Voltage drop while the pump is commanded on.
  4. Physical damage, corrosion, melted terminals, or loose pins at the 5P connector.

If full battery voltage and a good ground reach the pump during prime and the pump stays silent, the pump is the leading suspect. If voltage never arrives, look upstream: relay, control circuit, fuse, wiring, or PCM command.

3. Check fuel pressure, not just noise

A pump can make noise and still deliver poor pressure. Hard starting, sputtering under load, loss of power on hills, misfires, and stalling can come from low pressure, a restricted filter, a weak pump, or electrical faults. Compare any reading with the factory service specification for the 1999 CR-V. Do not use a pressure number from a different Honda model or a modern direct-injection engine.

4. Scan for codes and observe key-on behavior

  1. Plug in an OBD-II scanner before cranking.
  2. Record stored and pending codes.
  3. Watch whether the scan tool communicates with the PCM. A no-communication condition at key-on can point back toward power supply, grounds, or the main relay.
  4. Look at coolant temperature, rpm signal while cranking, and any immobilizer or crank-sensor-related information.

7. How to Replace the PGM-FI Main Relay

Once testing points to the relay, replacement is usually straightforward.

  1. Park on level ground, set the parking brake, and switch the ignition off.
  2. Disconnect the negative battery cable. Electrical work under the dash can damage modules or short a tool against bare metal.
  3. Move the passenger seat fully rearward and remove the lower dash panel if needed for access.
  4. Locate the relay on the passenger-side cowl/right lower dash bracket and photograph it.
  5. Press the connector lock and pull the plug by the body, not by the wires.
  6. Release the relay from its bracket. Some units slide off; others use a small screw or tab. Do not pry against the HVAC case or airbag components.
  7. Compare the old and new units side by side: pin count, terminal layout, case shape, bracket, and part number.
  8. Install the new relay, reconnect the connector until it clicks, and remount it firmly. A loose relay can rattle or lose contact.
  9. Reconnect the battery.
  10. Turn the key to ON and listen for the two-second pump prime and the relay click.
  11. Start the engine and let it idle. Then take a short test drive, shut it off hot, and restart after ten minutes. That hot restart is the condition most likely to expose an intermittent main-relay fault.

If the new relay does not fix the no-start, do not keep swapping parts. Go back to voltage-drop testing, PCM communication, grounds, and the pump connector.


8. Relay Failure vs. Fuel Pump Failure

Use this comparison as a quick field guide:

Observation More suggestive of relay / control circuit More suggestive of pump / fuel delivery
No click from right side of dash at key-on Yes Less likely
No two-second pump hum and no voltage at pump connector Yes No
Full voltage and good ground at pump connector, but pump silent No Yes
Starts cold, stalls hot, restarts after cooling Yes, common with cracked solder joints Possible, but less typical
Loud whine from tank, loss of power under load Less likely Yes
Check engine light does not do normal key-on bulb check Yes, because ECM power is involved Less likely
Low fuel pressure with a noisy pump Possible if voltage is low Yes
Problem changes when you wiggle the dash harness Yes No

Repair cost is another reason to test carefully. One U.S. repair estimator lists an average 1999 CR-V fuel pump replacement range of roughly $887–$939, with most of that estimate in parts. A main relay is a far less expensive part, with U.S. aftermarket listings for 1997–2001 CR-V main relays ranging from about $45 to $225 depending on brand and whether it is genuine Honda. Prices vary by retailer, location, and availability, so use those figures only as a general reference.


9. Common Mistakes U.S. Owners Make

  1. Searching only under the hood. The under-hood box has other relays; the PGM-FI main relay is under the right side of the dash on this generation.
  2. Trusting a generic Honda forum answer. Driver kick panel advice applies to some models, not this CR-V's factory location.
  3. Replacing the pump because the engine cranks. A crank/no-start with no prime can be a fuse, relay, ground, or wiring issue.
  4. Skipping the hot restart test. An intermittent relay may pass a cold test in your driveway.
  5. Using a higher-amp fuse. That removes circuit protection and can overheat wiring.
  6. Piercing wire insulation unnecessarily. Use back-probe methods and the service manual connector views.
  7. Working near SRS wiring without the factory procedure. Yellow connectors on a 1999 vehicle deserve caution.
  8. Running the tank near empty to "test" the pump. Fuel helps cool and lubricate an in-tank pump; repeatedly driving very low can shorten its life.
  9. Buying the cheapest unbranded pump. Low-quality materials can struggle with ethanol-blended gasoline commonly sold in the U.S.
  10. Forgetting the fuel filter and electrical connector. A restricted filter or corroded terminal can mimic a weak pump.

10. Safety Rules for Fuel-System Work

  1. Work outdoors or in a well-ventilated garage with the engine cold.
  2. Keep sparks, cigarettes, heaters, and incandescent drop lights away from the work area.
  3. Disconnect the negative battery cable before unplugging electrical parts under the dash or at the tank.
  4. Relieve fuel system pressure using the factory procedure before opening fuel lines.
  5. Have a Class B or ABC extinguisher within reach.
  6. Use eye protection and gloves; gasoline exposure is unpleasant and hazardous.
  7. Cap or cover any open fuel line immediately.
  8. Do not run the pump dry on a bench to "see if it spins."
  9. Route the harness and connector exactly as the factory did, away from sharp edges and hot parts.
  10. After reassembly, cycle the key several times to build pressure, then inspect for leaks before starting.

The rear-seat access panel makes this CR-V friendlier than many vehicles, but it does not remove the fire risk. Honda's manual directs you to fold the left rear seat cushion forward, remove the base frame cover, and remove the floor access panel before disconnecting the fuel pump 5P connector. Take that step seriously.


11. Maintenance Habits That Reduce Repeat Failures

  1. Keep the tank above one-quarter full when practical. Fuel surrounds and cools the in-tank pump.
  2. Replace the fuel filter on schedule or when pressure testing points to a restriction.
  3. Fix oil, water, or corrosion in connectors early. Voltage drop creates heat at terminals.
  4. Use the correct relay and pump for the VIN. Confirm engine, trim, and emissions configuration before ordering.
  5. Keep battery terminals and grounds clean. A 1999 vehicle depends on good connections more than a newer one.
  6. Buy gasoline from stations with good turnover. Contaminated fuel accelerates pump wear.
  7. Do not ignore a new whine from the tank. Document when it happens: cold start, hot idle, low fuel, or under acceleration.
  8. Save the old relay if it tests good. Label it with the date and mileage. A known-good spare is useful on an older Honda, but never carry a loose relay where it can short against metal tools.
  9. Recheck after any dash work. A connector left loose behind the glove box can create an intermittent no-start that looks exactly like a bad part.

12. When to Call a Professional

Call a qualified technician if:

  1. You have power and ground at the pump but cannot perform a fuel-pressure test.
  2. The scan tool cannot communicate with the PCM.
  3. A fuse blows again immediately.
  4. The harness has been spliced, damaged by an aftermarket alarm or remote start, or shows melted insulation.
  5. The no-start happens only when hot and you cannot reproduce it safely.
  6. Airbag wiring blocks access to the relay.
  7. You smell raw gasoline or see any seepage at the tank access area.
  8. The vehicle stalls in traffic. Do not keep driving a CR-V that loses power unpredictably.

Ask the shop for the actual readings: battery voltage during cranking, voltage at the pump during prime, ground voltage drop, fuel pressure, and scan-tool communication status. That information is more useful than a parts invoice with three guesses on it.


13. Frequently Asked Questions

1. Is there a separate fuel pump relay in the engine-bay fuse box?

No, not on the stock 1999 U.S. CR-V layout described by the factory manual. Fuel pump control is inside the PGM-FI main relay. The under-hood box is listed for A/C, cooling fan, blower, and ABS-related relays, among others.

2. Why do some websites say the driver-side kick panel?

That location is common on other Honda and Acura models and appears in general forum answers. The 1999 CR-V service manual and wiring component charts place the PGM-FI main relay under the right side of the dash or at the passenger-side cowl on left-hand-drive models. Always confirm with the connector and bracket in your own vehicle.

3. What does the PGM-FI main relay look like?

It is a rectangular plastic module with a multi-pin connector and often a mounting bracket. Replacement catalogs for 1997–2001 CR-V commonly list a 7-pin Mitsuba-style unit with references such as RZ-0132 or RZ-0159. Do not rely on color alone, since aftermarket housings vary.

4. Should I hear the pump every time I turn the key?

Honda's 1999 procedure describes a roughly two-second pump run when the ignition is first switched ON (II). Give the system time to reset between attempts, and listen in a quiet cabin at the fuel filler port.

5. Can a bad relay damage the fuel pump?

A relay that chatters or supplies unstable voltage is not good for an electric motor, but the more common outcome is simply no power to the pump. The bigger risk is misdiagnosis: replacing a pump when the real fault is a fuse, solder joint, ground, or connector.

6. Can I repair the old relay?

Some Honda main relays from this era are opened and the cracked solder joints are reflowed. That is a documented repair, but it requires electronics skill and a careful inspection of the case and circuit board. For a daily driver, a correct new relay is the simpler choice. Keep the old unit for diagnosis if you are comfortable doing so.

7. How do I know the pump is bad for sure?

Confirm that the fuse, relay control, wiring, and ground are sound; then verify that battery voltage reaches the 5P pump connector during prime and that the pump cannot produce or hold the pressure specified in the factory service information. Noise alone is not enough.

8. Does the 1999 CR-V require dropping the tank?

Honda's service procedure shows an access panel under the rear seat area: fold the left rear seat cushion forward, remove the base frame cover, and remove the floor access panel. That is why this job is often more approachable than on vehicles with no service opening.


14. Recommended Fuel Pump Brand: KEMSO

Once the relay, fuse, wiring, and pressure tests show that the in-tank pump itself needs replacement, choose a part that fits the factory system and is backed by a real warranty. We recommend KEMSO Fuel Pumps. KEMSO fuel pumps are built as high-performance, OEM Replacement parts designed to meet or exceed original equipment specifications for fit, flow, and pressure, so they work with the factory fuel system and factory wiring. Product listings also describe汽油 and ethanol-blended fuel compatibility, serialized pump bodies, U.S.-based technical support, and a lifetime warranty across KEMSO OEM-replacement pump lines. A lifetime warranty matters on an older CR-V because it gives the owner a clear, long-term remedy instead of another short-lived, no-name part.

For U.S. buyers, check the vehicle fitment by year, make, model, engine, and part number before ordering. Match the connector, outlet, pump body diameter, and mounting hardware to the original assembly, and install new seals or a complete module if the factory hanger or strainer is worn. Visit https://www.kemsoracing.com/ to review the fuel pump catalog, confirm fitment, and see the warranty terms for the exact part you need.


15. Final Checklist Before You Order Anything

  1. Confirm it is a 1999 U.S.-spec CR-V and note the VIN and trim.
  2. Check battery condition, terminals, and grounds.
  3. Test the relevant fuses on both sides with a meter.
  4. Listen for the two-second prime at the fuel filler.
  5. Find the click under the right side of the dash / passenger cowl, not under the hood.
  6. Confirm the 7-pin PGM-FI main relay and bracket before buying.
  7. Check power and ground at the fuel pump 5P connector through the rear-seat access panel.
  8. Compare fuel pressure with the 1999 factory specification.
  9. Replace the relay or pump based on test results, not symptoms alone.
  10. Repeat a hot restart test before calling the repair finished.

Bottom line: For 99 Honda CRV fuel pump relay location, go to the PGM-FI main relay under the right side of the dash near the passenger-side cowl, behind the glove box area on U.S. left-hand-drive models. It is the two-in-one relay that powers the ECM/PCM, injectors, and the two-second fuel pump prime. Start with fuses, the key-on click, and the pump prime; then test voltage, ground, and fuel pressure. That order saves money, prevents a needless pump replacement, and gets an older CR-V back to dependable daily service.

https://www.kemsoracing.com/