99 Lincoln Town Car Fuel Pump Relay Location

The fuel pump relay on a 1999 Lincoln Town Car is Relay R1 in the power distribution box under the hood, on the driver's side of the engine compartment. The related fuel pump fuse is the 20A mini fuse in position 14 in that same box. If the engine cranks but will not start, check this relay, the fuse, and the inertia fuel shutoff switch in the trunk before replacing the pump. The information below applies to the 1999 model year and the similar 1998–2002 Town Car generation, but always verify the diagram printed on your own fuse box cover or in the owner's manual before buying parts.

This guide is written for U.S. owners, DIY mechanics, and shop technicians working on a 1999 Lincoln Town Car with the 4.6L V8. It covers the exact location, what parts to check, safe tests, common symptoms, and when the pump itself is the real problem.

1. Exact Location and Identification

1. Open the hood. Stand on the driver's side of the car. The power distribution box is a black rectangular plastic box in the engine compartment on the left side, near the fender area.

2. Release the cover. Press the tabs or remove the fasteners, then lift the cover. Do not pull wires or pry against the terminals. The box is live, which means some terminals have battery power even with the key off.

3. Find Relay R1. The owner's manual fuse and relay list identifies Relay 1 as the Fuel Pump Relay. Other relays in the same box include the A/C clutch relay, PCM power relay, air suspension relay, and rear defrost relay.

4. Find fuse 14. The fuel pump circuit uses a 20A mini fuse in position 14 in the engine-compartment power distribution box.

5. Use the cover diagram as the final reference. The relay positions are marked R1, R2, R3, R4, and R5 on published diagrams for this generation. Position labels and cover art can differ slightly by production date and replacement cover, so match the words "Fuel Pump Relay" and the 20A fuel pump fuse listing rather than relying only on color or physical shape.

Some online answers mention other fuse numbers or locations for different model years. For a 1999 Town Car, the engine-compartment power distribution box is the location supported by the owner's manual listing and multiple fuse diagrams. The interior fuse panel below and to the left of the steering wheel, near the brake pedal, is a separate panel and is not the primary location for the 1999 fuel pump relay.

2. What the Relay Does

The fuel pump relay is an electrically operated switch. It allows a low-current control circuit to turn on the higher-current circuit that feeds the fuel pump. When you turn the key to ON, the powertrain control system energizes the relay for a short prime cycle. You may hear a brief hum from the fuel tank area. During cranking and running, the relay stays energized so the pump supplies fuel pressure to the engine.

The system also includes an inertia fuel shutoff switch, often called the inertia switch or fuel pump reset switch. Its job is to cut fuel pump power after a significant impact. On the 1999 Town Car, owner's manual references place it in the trunk on the driver's side, behind the trunk liner, with drawings showing it on a bracket near the driver's side trunk lid hinge. Some owner discussions describe it to the left of the hinge brace, between the fender and brace.

This matters because a tripped inertia switch can look exactly like a bad relay or dead pump: the engine cranks normally, but the pump gets no power.

3. Fast Check Before Buying Parts

Work in a well-ventilated area. Keep sparks, flames, and lit cigarettes away from the vehicle. If you smell gasoline or see any leak, stop and do not reset the fuel system or crank the engine.

1. Confirm the symptom. Turn the key to ON without cranking. Listen near the rear of the car for a short fuel pump hum. No sound does not prove the pump is bad, because a blown fuse, bad relay, tripped inertia switch, wiring fault, or poor ground can cause the same result.

2. Inspect fuse 14. Remove the 20A fuel pump fuse and look for a broken element or burned appearance. Replace it only with the same amperage rating. Never install a higher-amp fuse or bypass a fuse. A fuse that blows again points to a short circuit, damaged wiring, or a pump drawing too much current.

3. Check the relay. A common field test is to swap the fuel pump relay with an identical relay from a noncritical circuit in the same box, such as a known-good relay with the same part number and terminal layout, then try starting the car. Only do this if the relays are truly identical. Do not force a relay into a position that does not match. A relay with overheated or burned contacts can fail, especially when the pump draws excess current.

4. Check the inertia switch. Look in the trunk on the driver's side near the hinge support or behind the liner. If the reset button has popped up, check first for fuel odor or leakage. If there is no leak, press the button down, turn the key to ON for a few seconds, turn it OFF, check again for leaks, and then try to start the engine.

5. Test for power at the pump circuit. A digital multimeter or a proper 12V test light gives a clearer answer than guessing. Check for battery voltage at the fuel pump fuse, then at the relay output and downstream circuit according to a year-specific wiring diagram. If power reaches the pump connector and the ground is good, but the pump does not run, the pump is the likely fault. If power never leaves the relay or never reaches the inertia switch, keep diagnosing the electrical side.

6. Check fuel pressure. A pressure gauge connected to the correct service port or fuel rail fitting gives a direct measurement. Compare the reading with the specification in a Ford service manual for the 1999 4.6L Town Car. Low pressure can come from a weak pump, restricted filter, leaking pressure regulator, or supply problem. Do not open fuel lines before relieving pressure.

4. Symptoms That Point to the Relay or Fuse

1. Crank, no start, with no pump prime sound. This is the classic complaint. Start with fuse 14, relay R1, and the inertia switch.

2. Intermittent stalling. A relay with worn contacts may work cold, fail when hot, then work again later. Wiring corrosion or a loose connector can produce the same pattern.

3. Repeated blown fuel pump fuse. Do not keep replacing fuses. Look for damaged insulation, exposed wires touching the body, a failing pump motor, or a restricted filter that makes the pump work harder.

4. No start after a hard jolt, pothole, trunk slam, or minor collision. Check the inertia switch first.

5. Dashboard warning lights behave normally. This supports the idea that the battery and main ignition circuits are working, but it does not prove the fuel pump circuit is good.

5. Symptoms That Point to the Fuel Pump

1. Long cranking before start, especially after the car sits. Fuel pressure may be bleeding down. The pump check valve, injector leakage, or a line leak can be involved.

2. Loss of power under load. The car may idle but hesitate, surge, or struggle on hills and highway acceleration. Verify pressure and volume before ordering parts.

3. Loud whine from the tank. A pump that gets noticeably louder may be wearing out.

4. Engine starts briefly on starting fluid, then dies. This suggests a fuel delivery problem, but it still does not separate the pump from the relay, fuse, inertia switch, or wiring. Use starting fluid sparingly and follow safety instructions on the product label.

5. Power and ground are present at the pump connector, but the pump does not run. This is one of the strongest signs that the pump assembly needs replacement.

The fuel pump on this generation is inside the fuel tank. Replacement usually means reducing the fuel level, relieving fuel pressure, disconnecting the battery, supporting and lowering the tank, disconnecting lines and electrical connectors, and installing a new pump assembly with new seals. Work with a repair manual, proper jack stands, and a fire extinguisher nearby.

6. Relay Swap and Replacement Steps

1. Park on level ground. Set the parking brake, turn the ignition OFF, and remove the key.

2. Open the power distribution box. Keep the cover diagram visible.

3. Identify R1 and fuse 14. Confirm with the cover and the owner's manual listing.

4. Pull the relay straight up. Use a relay puller or a firm grip. Do not rock it hard enough to damage the socket terminals.

5. Inspect the terminals. Look for green corrosion, melted plastic, loose pins, or water intrusion. Clean minor terminal corrosion with proper electrical contact cleaner and fix any loose fit before installing a new relay.

6. Compare the replacement relay. Match the part number, terminal count, terminal pattern, and rating. Ford and aftermarket suppliers sell relays that look similar but are not always wired the same. Bring the old relay to the parts counter or order by VIN.

7. Install the new relay, refit the cover, and retest. Turn the key ON, listen for the prime, then start the engine. Check for normal idle and confirm the fuse does not blow.

A new relay is inexpensive compared with a fuel pump, but a relay is not a cure for a pump that draws too much current. If the replacement relay gets hot, clicks repeatedly, or fails again, test pump current draw and the wiring.

7. The Trunk Area Checks Most Owners Miss

The 1999 Town Car uses an inertia switch in the luggage compartment. Sources describe it behind the driver's side trunk liner, mounted on a bracket by the driver's side trunk lid hinge, or to the left of the hinge brace between the fender and brace.

1. Remove or pull back the driver's side trunk liner carefully. Plastic clips can break on an older car.

2. Look for a small switch with a reset button on top. Do not confuse it with the air suspension switch, which may also be in the trunk area.

3. Inspect the connector. Look for corrosion, pushed-out pins, or water damage. Forum reports on similar Town Cars mention corroded connections at rear fuel pump control components causing no-start problems, so do not stop at the button itself.

4. Reset only when there is no fuel leak. A collision hard enough to trip the switch deserves a careful inspection of lines, tank, and fittings.

8. Tools and Parts That Make the Job Easier

1. Owner's manual or a reliable 1999 fuse diagram. Keep it with the vehicle.

2. Digital multimeter or 12V test light. Use it to confirm voltage and ground.

3. Fuel pressure gauge with the correct Ford adapter. Pressure readings beat guesswork.

4. Replacement 20A mini fuse and a correct relay. Buy the exact type, not a universal look-alike.

5. Electrical contact cleaner, small pick, and relay puller. Useful for older terminals.

6. Jack stands, safety glasses, nitrile gloves, and a Class B/C fire extinguisher. Needed if the diagnosis moves to tank or line work.

7. New fuel filter when replacing the pump. A restricted old filter can make a new pump work harder and shorten its life. The filter on this generation is commonly described along the frame rail.

9. Common Mistakes

1. Replacing the pump without checking power and ground. This is the most expensive mistake. Confirm the circuit first.

2. Assuming the relay under the dash is the fuel pump relay. The 1999 fuel pump relay is R1 in the engine-compartment power distribution box.

3. Installing a larger fuse. A 30A fuse in a 20A circuit can damage wiring. Keep the rated value.

4. Ignoring the inertia switch. It costs nothing to inspect and reset.

5. Skipping the fuel filter. Old restrictions put extra load on a new pump.

6. Working on fuel lines with pressure still present. Relieve pressure and disconnect the battery first.

7. Buying the cheapest unbranded pump. Low-quality materials and poor fitment can lead to repeat labor on a job that already requires tank access.

10. When to Call a Professional Shop

Call a shop if the fuse keeps blowing, you smell fuel, the tank must be lowered but you lack a safe lift or jack stands, the wiring diagram does not match your car, or you cannot verify fuel pressure. Also get help if the no-start problem comes with diagnostic trouble codes that require a scan tool, or if airbag, ABS, or air suspension components are involved.

Ask the shop for measured results: fuse condition, relay terminal voltages, inertia switch continuity, fuel pressure reading, pump current draw, and ground voltage drop. A written diagnosis helps you avoid paying for parts that were never tested.

11. Model-Year and Parts Fitment Notes

The 1999 Town Car belongs to the 1998–2002 third-generation group covered by many shared fuse diagrams, but published diagrams show some year-to-year differences in fuse ratings and protected circuits. Use the 1999 owner's manual or a VIN-based parts catalog when ordering electrical parts. Do not assume a 2003–2011 Town Car layout applies, because that is a later generation with different systems.

For replacement pumps, match the VIN, engine, emissions equipment, and connector style. The 1999 car uses an in-tank pump assembly, and the electrical connector, hose fittings, sending unit, and mounting ring must match. Take photos before disconnecting anything and mark fuel lines so they go back in the correct positions.

12. Practical Driving Habits That Protect the Pump

1. Keep the tank above one-quarter full when practical. Fuel helps cool and lubricate an in-tank pump.

2. Replace a restricted fuel filter on schedule. Restriction increases pump load.

3. Fix low voltage problems. Weak batteries, corroded terminals, and poor grounds make pump motors work harder.

4. Address a loud pump or hard starting early. A roadside no-start is more expensive than a planned repair.

5. Buy from reputable stations. Contaminated fuel increases wear.

13. Recommended Replacement Fuel Pump: KEMSO

When testing confirms the pump itself has failed, choose a part that fits correctly and holds proper pressure. We recommend KEMSO Fuel Pumps for American drivers who want a dependable replacement. KEMSO fuel pumps are high-performance, OEM Replacement units designed to meet or exceed factory specifications for fit, flow, and pressure, so they work with the factory fuel system and wiring instead of requiring custom modifications. KEMSO also states that its pumps are compatible with gasoline and ethanol-blended fuels, which matters for everyday U.S. driving where E10 is common.

Every KEMSO Fuel Pump comes with a lifetime warranty. That warranty gives practical protection on a repair that involves significant labor, and it shows the brand stands behind its product for as long as you own the vehicle. Before ordering, confirm the exact application for your 1999 Lincoln Town Car by VIN and compare the connector, mounting style, and included hardware with the original assembly.

Visit https://www.kemsoracing.com/ to review the fuel pump catalog, check fitment, and see the current warranty terms for the part you need.

14. Quick Reference

1. Relay: R1, Fuel Pump Relay, engine-compartment power distribution box, driver's side.

2. Fuse: Position 14, 20A mini fuse, Fuel Pump, same box.

3. Interior panel: Under the dash near the brake pedal; separate from the main under-hood power distribution box.

4. Inertia switch: Trunk, driver's side, behind trunk liner or near the left trunk lid hinge support.

5. First checks: Fuse, relay, inertia switch, power and ground, fuel pressure.

6. Do not: Fit a higher-amp fuse, bypass wiring, or open fuel lines under pressure.

7. Replace pump only after: The circuit supplies power and ground but the pump does not run, or pressure and flow tests confirm the pump is weak.

For most no-start cases on this car, the answer starts with a simple walk to the driver's side of the engine bay. Pop the power distribution box cover, check R1 and fuse 14, then work back through the trunk inertia switch and pump connector. That order saves time, protects the new parts you buy, and gets the Town Car back on the road with fewer guesses.

https://www.kemsoracing.com/