99 Mustang Fuel Pump Relay Location: Quick Answer and Full Guide

On a 1999 Ford Mustang, the fuel pump relay is not a small plug-in relay in the under-hood fuse box. It is inside the Constant Control Relay Module, usually called the CCRM. On many 1999 Mustangs, the CCRM sits in the right-front fender area near the air filter and intake path, where the wheel and inner fender liner often have to come off for access. Ford-style service information describes the CCRM as controlling PCM power, the cooling fan, the A/C clutch, and the power supply relay for the Fuel Pump Driver Module (FPDM), while wiring-diagram indexes place the module inside the right-front fender behind the air filter housing on 1999 Mustangs. If you are looking for a separate four- or five-pin cube marked “fuel pump,” you will waste time pulling parts from the power distribution box. Check the fuses and the inertia switch first, test the circuit, then decide whether the CCRM or the in-tank pump is at fault.

This guide is written for U.S. owners of a 1999 Mustang V6 3.8L, GT 4.6L, and Cobra. Confirm your engine, VIN, production date, and any previous wiring changes before ordering parts. A previous owner may have installed an aftermarket pump, relay kit, alarm, remote start, or engine swap harness. That changes what you see on the car.

1. The short answer most owners need

  1. Look for the CCRM, not a standard relay. A discussion about a 1999 GT identifies the fuel pump relay as a component within the CCRM and describes the module as a sealed unit that also contains relays for PCM power, the A/C clutch, and the engine cooling fan.
  2. Go to the passenger-side front fender area. Mustang owner discussions and a 1999–2004 GT guide place the CCRM in the right-front fender area near the air-cleaner/intake route, with wheel and inner fender liner removal commonly needed for access. A 1999 wiring-diagram index gives “inside right front fender, behind air filter housing” as one CCRM location.
  3. The relay is not normally serviced by itself. A KEMSO article about the similar 1998 Mustang says the fuel pump relay is soldered to the CCRM circuit board and is not separately serviceable, so the usual repair is replacing the complete CCRM. A 1999 GT forum answer states that the sealed module has to be replaced if one internal relay fails.
  4. Check the under-hood power distribution box for fuses. A 1999 V6 fuse-box reference lists the constant-control-relay circuit among the high-current circuits in the engine-compartment box, and a 1999–2004 Mustang fuse guide describes separate passenger-compartment and under-hood fuse panels. Use your owner’s manual, the fuse-box lid, or a year- and engine-specific wiring diagram to identify the exact fuel-system fuse before testing.
  5. Do not confuse the relay with the inertia switch. Mustang discussions describe the inertia switch in the trunk area and mention resetting its red button; the fuel pump itself is inside the fuel tank.

A no-start condition is not proof that the CCRM is bad. A blown fuse, tripped inertia switch, weak battery, poor ground, damaged connector, worn pump, clogged filter, or broken wire can produce the same complaint.

2. Why the 1999 Mustang is confusing

Many American cars from the 1990s used a simple relay that you could pull from a fuse box and swap with the horn or A/C relay to test it. That habit causes problems on a 1999 Mustang.

Ford grouped several high-load controls into one module. Ford-based service text for the 1999 Mustang V6 says the CCRM provides Vehicle Power (VPWR) to the PCM and the electronic engine-control system, controls the cooling fan and A/C clutch, and contains the FPDM power-supply relay. A 1999–2004 GT CCRM guide warns against buying modules before testing the circuit because no-start, cooling-fan, and A/C complaints can all point toward the same part.

Parts stores and generic websites sometimes give the wrong answer. Search results for this exact question include claims that a plug-in fuel pump relay sits in the under-hood relay box, that it is under the dashboard, and that the 1999 Mustang has no fuel pump relay at all. Those descriptions conflict with the 1999 service description and wiring-diagram index that identify a CCRM with an FPDM power-supply relay. A generic answer may belong to another Mustang generation, another model year, or a different Ford vehicle. If a parts counter shows you a small cube relay, ask for the application by VIN and engine, then compare the connector and module part number with the unit on your car.

Terminology also varies. You may see “CCRM,” “constant control relay module,” “integrated control relay module,” “fuel pump driver module,” “FPDM,” “fuel pump relay,” and “fuel pump power supply relay” used loosely. The CCRM is the front-mounted relay module. The FPDM is a separate control device in the returnless fuel system on many 1999–2004 cars, and the fuel pump motor is in the tank. Ask which part the writer means before buying anything.

3. Where to look, step by step

1. Park safely. Set the parking brake, switch off the ignition, work on level ground, and let the engine cool. Keep sparks, cigarettes, and heaters away from the fuel system. Wear eye protection.

2. Open the hood and inspect the power distribution box. On this generation, there is an engine-compartment box for high-current fuses and a passenger-compartment fuse panel. The box lid or owner’s manual is the first place to confirm the fuel-pump-related fuse for your exact car. One 1999 fuse reference lists a 20-amp mini fuse for the fuel pump in the engine-compartment power distribution box, while another answer describes a mini fuse under the driver-side dash for 1999-and-newer returnless systems. Because those references disagree, trust the diagram for your VIN and verify by testing both sides of the fuse with a test light or multimeter rather than relying on a number copied from a forum.

3. Find the CCRM. Stand at the passenger-side front wheel and look toward the air filter and intake opening. A 1999 GT owner answer places the CCRM inside the right front fender just aft of the intake-tube opening and says the wheel and fender liner have to be removed for access. A 1999–2004 GT guide gives the same right-front fender area beside the air-cleaner/intake route and notes that the guide applies to stock 4.6L 2V GT wiring, while V6, Mach 1, Cobra, and Cobra R applications need their own diagrams. A 1999 wiring-diagram index also lists the CCRM inside the right front fender behind the air filter housing and, in another location entry, mounted on a bracket behind the engine coolant reservoir. That is why a visual check matters: do not assume every 1999 engine bay or replacement bracket matches one photo.

4. Identify the part before unplugging it. Expect a sealed black module with a multi-pin electrical connector attached to a bracket. A used 1999–2004 V6 CCRM listing describes a relay and diode pack with Ford part number XR3F-12B581-AC, direct-fit mounting at the front, and no programming required. Use that number only as an example of what a V6 module listing may show. CCRM part numbers vary by engine and year, and a 1999–2004 GT guide warns that pin assignments are year-specific and that other Mustang trims require their own diagrams.

5. Do not pry the sealed case open to replace one internal relay. The usual field repair is a complete module when testing proves the CCRM is faulty. Opening it can damage the board, seals, and connector, and it may leave you with a car that still does not start.

4. How to access the CCRM without damaging anything

1. Disconnect the negative battery cable. Wait before unplugging electrical connectors. This reduces the chance of a short while you work around the fender and intake area.

2. Loosen the passenger-front wheel lug nuts, then raise and support the car. Use a jack stand on the proper support point. Never work under a car held only by a hydraulic jack.

3. Remove the wheel. A 1999 GT discussion specifically says the wheel and fender liner must be pulled to reach the module.

4. Remove the plastic inner fender liner fasteners. Keep the clips in a tray and note where each one goes. Some clips break with age, so replacement push pins are cheap insurance.

5. Locate the module and inspect the connector. Look for corrosion, water intrusion, pushed-out pins, melted terminals, loose grounds, and harness rubbing near the radiator support. A 1999–2004 Mustang discussion recommends checking the grounds around the radiator core support when diagnosing a clicking module in the right-front fender.

6. Release the connector lock and pull on the connector body, not the wires. Old Ford connectors can be brittle. A damaged lock tab can cause an intermittent no-start later.

7. Match the replacement before installation. Compare the housing shape, mounting bracket, connector keying, pin count, and part number. A 1999–2004 GT guide stresses year-specific connector pin assignments and warns that V6, Mach 1, Cobra, and Cobra R applications require their own diagrams.

8. Reconnect, reinstall the liner and wheel, torque the lug nuts to the vehicle specification, and retest. Do not leave the car on jack stands for a fuel-system test.

5. Symptoms that point toward the relay circuit

The CCRM supplies power to several systems, so a failing module may create more than one complaint. Ford service text names the PCM power supply, cooling fan, A/C clutch, and FPDM power-supply relay as CCRM functions. A 1999–2004 GT guide lists a no-start, an uncooperative cooling fan, and an A/C clutch that will not engage as common reasons owners start looking at the module.

1. The engine cranks but does not start. The starter works, but you may not hear the brief pump prime when the key first turns to ON. Silence is not final proof; cabin noise, a noisy starter, or a failed pump can mislead you.

2. The car starts after several key cycles. A right-front fender clicking sound when the key is in RUN, followed by starting after several cycles, appears in a Mustang forum discussion identifying that fender component as the CCRM. Repeated clicking can also come from low system voltage or poor grounds, so test the battery and charging system before condemning the module.

3. The engine stalls while hot, then restarts after cooling. Heat can affect a weak electrical component, but a failing in-tank pump, vapor issues, crank sensor, or wiring fault can behave the same way. Use a scan tool and fuel-pressure test rather than guessing.

4. The cooling fan or A/C clutch acts up with the fuel complaint. Because the CCRM contains multiple control relays, more than one system failing at once raises suspicion about shared power, grounds, or the module.

5. The pump runs when supplied with tested power, but not through the vehicle harness. That points toward control, wiring, fuses, inertia switch, grounds, connector, or CCRM. Have a qualified person perform this test. Jumping power near a fuel leak is a fire risk, and KEMSO’s fuel-pump troubleshooting guide says powering a pump with jumpers near fuel leaks is a serious fire risk.

6. A practical diagnostic order for a crank/no-start

Start with the cheapest and least invasive checks.

1. Confirm the complaint. Turn the key to ON and listen for the short pump prime. Do this with the radio, blower, and other loads off. Check whether the check-engine light comes on with the key, which helps confirm PCM power.

2. Check battery voltage and battery terminals. A 1999 Mustang with low voltage can produce confusing relay clicks and module behavior. A StangNet troubleshooting list includes checking grounds and fuses with a volt-ohm meter and notes that a weak battery and charging system can make these cars run poorly.

3. Test the relevant fuses with a test light on both test tabs. Do not replace a fuse by appearance alone. A fuse-box reference for the 1999 Mustang lists CCRM-related high-current circuits in the engine-compartment box, and a 1999–2004 guide says some circuits differ by model year, engine, Cobra equipment, and audio option. If a fuse blows again, find the short instead of installing a larger fuse.

4. Check the inertia switch. Mustang forum discussions mention the inertia switch and its reset button, with one answer placing a rollover switch in the trunk on the driver side near the tail light. Press the reset button only after inspecting for leaks or collision damage. An inertia switch that trips repeatedly needs diagnosis.

5. Scan for diagnostic trouble codes. Ford-based no-start discussions mention codes related to fuel-pump relay or driver circuits, and a 1999–2004 GT guide refers to Ford pinpoint-test branches. Write down the exact code number before clearing anything.

6. Check fuel pressure at the Schrader valve on the fuel rail. Use a gauge rated for gasoline and follow the service procedure for your engine. A guide about testing fuel pressure on a 1999 Mustang V6 describes checking the fuse and using basic electrical tests before deeper diagnosis. Low or zero pressure moves the investigation toward the pump, filter, wiring, or control circuit; normal pressure means you should look at spark, injector pulse, compression, and security/starting systems.

7. Inspect the CCRM connector, grounds, and harness. A StangNet thread advises following wiring from the pump to the CCRM and checking for damaged wiring and poor connections. Another discussion recommends checking grounds around the radiator core support when a front-right-fender module clicks.

8. Test power and ground at the pump harness before dropping the tank. A 1999 Cobra owner trying to drain old fuel asked about checking pump voltage without dropping the tank and reported good voltage at the inertia switch; the discussion also mentions locating the fuel pump relay in the passenger wheel well. Use a proper wiring diagram for the exact model. Back-probe connectors carefully; do not pierce insulation unless the repair manual allows it, then seal any damaged wire.

9. Decide between CCRM, FPDM, wiring, and pump. A 1999 V6 service description says the CCRM contains the relay that supplies power to the FPDM. That means power at one point does not prove the entire delivery chain works. A module with an internal relay failure is normally replaced as a complete unit, while the in-tank pump is a separate repair.

7. CCRM, FPDM, fuse, inertia switch, and fuel pump: what each one does

1. CCRM: The front-mounted relay module that interfaces with the electronic engine-control system and houses several relays, including the FPDM power-supply relay on the 1999 V6 described in factory-style service text. A 1999 GT forum description says the sealed module includes fuel pump, PCM power, A/C clutch, and cooling fan relays.

2. FPDM: The fuel pump driver module. Ford-style service text for a 2000 Explorer describes the CCRM as controlling FPDM operation, and 1999 Mustang V6 text says the CCRM contains the FPDM power-supply relay. Do not use those two names for the same part when ordering.

3. Fuel-system fuse: Protects the circuit. A 1999 fuse reference lists a 20-amp mini fuse for the fuel pump in the under-hood power distribution box, while another source describes a 20-amp mini fuse under the driver-side dash for 1999-and-later returnless systems. Because published references disagree, verify with the owner’s manual, lid diagram, or vehicle-specific wiring diagram.

4. Inertia switch: A safety shutoff that can interrupt fuel pump operation after an impact or jolt. Mustang discussions mention resetting the red button and place it in the trunk area on the driver side near the tail light.

5. Fuel pump: The electric pump inside the fuel tank. A 1999 Mustang guide describes the pump, fuel sender, and related components at the fuel tank and says access requires caution around the fuel system.

8. Tools and parts that make the job easier

1. Basic tools: A lug wrench, floor jack, jack stands, wheel chocks, trim-clip tool, socket set, small flat screwdriver for connector locks, flashlight, and gloves.

2. Electrical tools: A 12-volt test light and a digital multimeter. A StangNet checklist describes checking both ends of fuses with a volt-ohm meter and using continuity testing on de-energized fuses.

3. Fuel tools: A fuel-pressure gauge suitable for gasoline, a scan tool that can read Ford codes, and the correct service information for the VIN.

4. Consumables: Replacement fender-liner clips, electrical contact cleaner approved for connectors, dielectric grease where the service manual calls for it, and a fire extinguisher rated for flammable-liquid fires.

5. Replacement parts: Only buy after testing. If the CCRM is at fault, match the part number and connector. If the pump is at fault, replace the strainer and consider the external fuel filter at the same time; KEMSO’s priming guide recommends replacing the strainer with a new pump and not feeding a new pump through an old, debris-filled filter.

9. What a repair shop will usually check

A professional diagnosis should start with the customer complaint, battery and charging system, scan codes, fuse and relay control, fuel pressure, and power/ground at the pump. A 1999–2004 GT CCRM guide says to stop buying modules before testing the circuit and notes that factory checks must be matched to the symptom and the correct pinpoint-test branch. If a shop quotes a CCRM replacement immediately after a no-start without recording fuel pressure or circuit tests, ask for the test results.

Ask for these three items before approving the repair:

  1. The exact codes and fuel-pressure reading.
  2. The test points that showed missing power or ground.
  3. The part number and wiring diagram used for your VIN and engine.

This is especially important on modified cars. Supercharger kits, aftermarket fuel systems, remote start, alarm wiring, and engine swaps can add relays or bypass factory wiring. A 1999–2004 GT guide limits its pin assignments to stock 4.6L 2V GT wiring and says other applications need their own diagrams.

10. Safety rules for fuel and electrical work

1. Work outdoors or in a well-ventilated area. Gasoline vapor is heavier than air and can collect in low spaces.

2. No smoking, no open flames, and no sparks. Disconnect the negative battery cable before opening connectors around the fuel system.

3. Relieve fuel pressure before opening a line. KEMSO’s troubleshooting guide says to relieve pressure by removing the fuel pump fuse and running the engine until it stalls, then disconnecting the battery, working in a well-ventilated area, and keeping a fire extinguisher nearby. Follow the factory procedure for your engine.

4. Never install a higher-amp fuse. If the fuse blows again, trace the short.

5. Stop if you smell raw fuel or find a wet tank seam. KEMSO’s priming guide says to stop immediately and call a professional if you smell raw fuel, see a wet tank seam, or find brittle harness insulation.

6. Support the vehicle properly. The CCRM is behind the fender liner, and dropping a fuel tank is heavier and more hazardous than it looks. If you lack jack stands, a fuel-pressure gauge, or confidence with wiring, use a qualified mechanic.

11. Common buying mistakes

1. Buying a generic cube relay. The 1999 Mustang relay circuit is built into the CCRM on the applications described here, and the internal relay is not normally replaced separately.

2. Ordering a CCRM for the wrong engine. A 1999–2004 GT guide says V6, Mach 1, Cobra, and Cobra R applications require their own diagrams, and a used V6 module listing gives a V6-specific Ford number. Match by VIN, engine, and part number.

3. Replacing the pump before checking the inertia switch and fuses. Forum troubleshooting repeatedly starts with fuses, grounds, the inertia switch, and key-cycle prime behavior.

4. Ignoring the cooling fan and A/C symptoms. Those systems share CCRM-related control functions, so a pattern of multiple failures may help diagnose a shared power or module problem.

5. Trusting one online answer. Published results for this exact model year disagree about the relay location and even its existence. Use a factory-style wiring diagram for your car.

12. V6, GT, and Cobra notes

1999 V6 3.8L: Factory-style service text describes the CCRM interfacing with the electronic engine-control system and containing the FPDM power-supply relay. A V6-specific used module listing shows part number XR3F-12B581-AC for 1999–2004 V6 cars. Verify against your own module before ordering.

1999 GT 4.6L: A model-specific guide places the CCRM in the right-front fender area beside the air-cleaner/intake route and says pin assignments are year-specific for stock 4.6L 2V GT wiring. A 1999 GT owner answer says the wheel and fender liner must be removed to access it.

1999 Cobra: A Cobra fuel-pump test discussion mentions locating the fuel pump relay in the passenger wheel well and checking voltage at the pump before dropping the tank. The 1999–2004 GT guide warns that Cobra applications require their own diagrams, so do not use GT pin data on a Cobra.

13. Frequently asked questions

Can I swap the fuel pump relay with the horn relay to test it?

Not on the stock 1999 Mustang setup described here. The relevant relay is inside the CCRM and is not a normal plug-in cube. Test the fuse, control circuit, connector, and pump circuit instead.

Does the 1999 Mustang have a fuel pump relay at all?

Yes in function, but not as a separately removable cube in the usual fuse box. The CCRM contains the FPDM power-supply relay according to Ford-style 1999 V6 service text. Some generic pages say there is no relay on the 1999 model, which appears to mean there is no separate serviceable relay.

Why do some guides say the relay is under the dash or in the under-hood box?

Those answers conflict with 1999 CCRM service information and wiring-diagram indexes. They may describe a different Ford, a different generation, a modified car, or an inaccurate generic database. Confirm with the VIN-specific diagram and the part on the vehicle.

Where is the fuel pump?

Inside the fuel tank. That is separate from the front-mounted CCRM and from the inertia switch in the trunk area.

How long does the pump prime when I turn the key on?

Use the factory service information for the exact engine. The important observation is whether a brief prime occurs consistently and whether the engine reaches the specified fuel pressure. Do not keep cycling the key to force a weak pump to start the car.

Can a bad CCRM cause an A/C or cooling fan problem too?

It can, because the module controls several systems. Ford-style service text lists PCM power, cooling fan, A/C clutch, and FPDM power supply among its functions. Test shared power and grounds before replacing the module.

Do I need to program a replacement CCRM?

A 1999–2004 V6 CCRM listing says no programming is required for that direct-fit used module. Still verify the correct part number for your car; the listing is for a V6 application and should not be treated as a universal rule.

Should I replace the CCRM when I replace the pump?

Not automatically. KEMSO’s priming guide lists a fuel pump relay as cheap insurance when replacing parts, but the 1999 Mustang setup requires the correct module and circuit testing rather than a generic relay swap. Replace the CCRM only when the test results point to it or you have a documented reason to do so.

14. Recommended replacement fuel pump: KEMSO

If testing confirms that the in-tank fuel pump is the failed part, we recommend KEMSO Fuel Pumps. KEMSO describes its pumps as high-performance OEM replacement units designed to meet or exceed factory specifications, with consistent fuel pressure and flow for stock or upgraded vehicles. KEMSO also states that its pumps are direct replacements for factory units, fit standard mounting locations without wiring, bracket, or fuel-line modifications, and are compatible with gasoline and E85/ethanol fuels.

Every KEMSO fuel pump comes with a lifetime warranty. KEMSO’s U.S. replacement-cost guide says the lifetime warranty protects the purchase for as long as you own the vehicle, and its troubleshooting article says the brand backs every pump with that coverage. Read the current warranty terms on the product page before ordering, including registration, proof of purchase, and coverage conditions.

1. High-performance: KEMSO says its pumps deliver consistent pressure and flow under demanding conditions, and one KEMSO article reports more than 20% additional flow at 43 psi compared with a stock OEM pump.

2. OEM replacement: KEMSO describes direct-fit installation using factory brackets and connections, with no custom wiring required.

3. Lifetime warranty: KEMSO says every pump is covered, reducing the cost and hassle of repeat replacement.

Check fitment by year, make, model, engine, and VIN before buying. The KEMSO site lists fuel pumps for cars, motorcycles, ATVs/UTVs, and personal watercraft, so choose the exact Mustang application rather than a universal pump. If your car has a modified fuel system, confirm flow, pressure, connector, and tank depth with the installer.

Visit https://www.kemsoracing.com/ to browse the full selection and find the correct fuel pump for your vehicle.

15. Final checklist before you order parts

  1. Record the symptom, engine, VIN, mileage, and any recent repairs.
  2. Test the battery, charging system, grounds, and relevant fuses.
  3. Check the inertia switch and scan for codes.
  4. Measure fuel pressure with the correct gauge.
  5. Inspect the CCRM connector and right-front fender harness.
  6. Use a VIN- and engine-specific wiring diagram before testing pins.
  7. Replace the CCRM only when circuit tests support it.
  8. Replace the pump only when power, ground, pressure, and control tests support it.
  9. Install the correct strainer and filter with a new pump.
  10. Retest for leaks, proper pressure, cold start, hot restart, cooling fan operation, and A/C operation.

The fastest route to a reliable repair is simple: find the CCRM in the right-front fender area, treat it as a sealed module, verify the fuse and inertia switch, then test the whole circuit before buying a module or dropping the tank. Generic relay advice wastes money on this car. Correct diagrams, measured voltage, and measured fuel pressure give you the answer.

For KEMSO high-performance OEM replacement fuel pumps with a lifetime warranty, visit https://www.kemsoracing.com/.