99 Silverado Fuel Pump Fuse: Quick Answer and Full Guide

If your 1999 Chevy Silverado cranks but will not start, check the 20A fuel pump circuit fuse and the fuel pump relay in the underhood electrical center before buying a pump. On the newer-style 1999 Silverado 1500 GMT800, the underhood center lists a 20A F58 fuse described as “Ignition Switch, Fuel Pump, PRND321 Display, Crank” and a separate Fuel Pump Relay, listed as R4 or F/PMP, depending on the label style used on the diagram. On the 1999 Silverado 2500 C/K GMT400, the underhood fuse/relay center uses a 20A mini fuse, No. 15, labeled ECM B, described as “Fuel Pump, PCM.” The 1999 model year is a changeover year, so the exact label depends on which Silverado body style you own. Use the diagram on the fuse box cover and the owner’s manual for your truck as the final authority.

A good fuse and a working relay do not prove the pump is good. The GM no-start procedure checks whether the fuel pump runs with a scan tool, then checks fuel pressure while the pump is operating. For the 4.8L, 5.3L and 6.0L Vortec engines, the GM service information gives 55–62 psi in that test. Some 1999 C/K documentation for the Central SFI system gives 60–66 psi with the pump running, so use the specification for your exact engine and fuel system rather than one number for every 1999 Silverado. If the fuse is blown, replace it only with the same amperage rating. If it blows again, stop replacing fuses and find the electrical fault.

1. Why the “99 Silverado fuel pump fuse” answer is not the same for every truck

1999 was a split year for Chevrolet trucks. The Silverado name appeared on the new GMT800 trucks, while older C/K GMT400 trucks were also sold in 1999. That matters because the fuse names, locations and circuit layouts are different.

1. Identify the truck before checking parts:

  1. 1999 Silverado 1500 GMT800: This is the newer body style. Fuse references for this truck include an underhood electrical center, an instrument panel fuse block and a center instrument panel utility block.
  2. 1999 Silverado 2500 C/K GMT400: This is the older body style. Its published underhood diagram lists ECM B as the fuel pump and PCM fuse.
  3. Engine and equipment differences: Gasoline and diesel versions can use different labels in the same general fuse center. Do not rely on a diagram from a 2000 or 2003 Silverado, and do not use a forum answer that does not name the body style.
  4. Use the VIN when ordering parts: A parts counter or online catalog should match the pump and module to the VIN, engine, cab, bed, fuel tank size and emissions equipment. A 4.3L V6, 4.8L V8 and 5.3L V8 truck do not automatically use the same pump assembly.

The practical reason this matters: A 20A fuse can be correct in one underhood box and the wrong circuit in another. Pulling the wrong fuse cannot fix a no-start and can create new electrical problems.

2. Where to look and what to check first

The underhood electrical center is the first stop on the GMT800, and the underhood fuse/relay center is also where the GMT400 ECM B fuse is listed. On the GMT800, the underhood electrical center is on the driver’s side of the engine compartment near the battery. The instrument panel fuse block is accessed through the driver’s side edge of the dash, and a fuse extractor may be mounted on the access door. Many published guides describe two main fuse areas: under the hood and inside the cab on the driver’s side.

2. Check these items in order:

  1. Turn the ignition off and remove the key. Park the truck, set the parking brake and work in a well-ventilated place.
  2. Open the hood and release the underhood cover. Read the printed label on the cover. Look for Fuel Pump, F/PMP, ECM B, ENG 1, IGN 1, INJ A or INJ B, depending on the diagram used for your truck.
  3. On a GMT800 diagram, check the 20A F58 fuse. Its published description includes “Ignition Switch, Fuel Pump, PRND321 Display, Crank.” Also locate the Fuel Pump Relay, listed as R4 in one diagram and F/PMP in another.
  4. On a GMT400 C/K diagram, check underhood fuse No. 15. It is a 20A mini fuse labeled ECM B, with the description “Fuel Pump, PCM.”
  5. Do not overlook related engine-control fuses. The GMT800 diagram also lists F21, 10A, “Engine Controls, Canister Purge, Fuel System”; F22, 20A, VCM/PCM; F30, 15A, “Ignition, Fuel Controls (Relay)”; F31, 10A, VCM/PCM; and F32, 15A, “Fuel Controls, Ignition.” These are not all the same as the fuel pump power fuse, but a problem in an engine-control or relay feed can still stop the engine from running.
  6. Replace a blown fuse with the identical size and rating. The 1999 Silverado owner’s manual says to inspect the silver-colored band and replace a bad fuse with one of identical size and rating. Do not install a 25A or 30A fuse to “get home.” A higher-rated fuse can allow wiring damage or a fire.

A visual check is not always enough. A fuse can look acceptable but still have a poor connection, corrosion or a break that is hard to see. A test light or multimeter gives a better answer. With the ignition on, a properly powered fuse should show voltage on both test points. GM’s no-start procedure uses a test lamp to probe both sides of underhood fuses, including engine and injector feeds.

3. What the fuse and relay actually do

The fuse protects the circuit. The relay switches power to the pump. The VCM or PCM controls the relay. When the ignition switch is turned ON, the VCM energizes the fuel pump relay, which powers the pump. The pump remains on while the engine is cranking or running and the control module receives reference pulses. If no reference pulses are present, the module shuts the pump off within about two seconds.

3. What this means during a no-start:

  1. You may hear a short pump prime. GM documentation says the pump operates for about 2 seconds when the ignition is turned ON, and fuel pressure must be observed while the pump is operating. GM also notes that removing the fuel cap may help you hear the pump.
  2. No sound does not automatically mean a dead pump. The fault may be the fuse, relay, control module command, wiring, connector, ground or the pump itself.
  3. The pump is inside the fuel tank. GM describes the electric pump as attached to the fuel level meter assembly inside the tank, sending fuel through an in-line filter, with a pressure regulator controlling pressure at the injectors and unused fuel returning to the tank. A KEMSO replacement guide also says the 1999 Silverado pump is in the tank and the module is replaced as a unit.
  4. A relay can fail even when the fuse is good. A common shop test is to compare the fuel pump relay with an identical, known-good relay from another noncritical circuit, then retest. Only swap relays with the same part number and terminal layout. KEMSO’s 1999 Silverado guide also recommends checking the relay and fuse before condemning the pump.
  5. A blown fuse is a symptom. A pump drawing too much current, damaged wiring, a short to ground or a connector problem can cause the fuse to open again. Repeating fuse replacements without testing the circuit is not a repair.

4. symptoms that point to fuel delivery, and symptoms that point elsewhere

Long cranking, stalling, loss of power under load and low fuel pressure are common fuel-delivery complaints. Published Silverado repair material lists hard starting, stalling at idle or low speed, poor acceleration, reduced fuel economy, whining from the tank and codes such as P0230 as possible signs. These signs are useful, but they do not prove the pump is the failed part.

4. Separate the complaints before spending money:

  1. Engine cranks normally but does not fire: GM’s no-start procedure assumes the battery and cranking speed are OK and says to make sure there is adequate fuel in the tank. Check the fuel pump command, fuse power, relay, pressure and injector/ignition feeds.
  2. Hard start after sitting: Pressure may bleed down after shutdown. GM’s fuel system diagnosis checks whether pressure remains constant after the pump stops and lists possible causes that include a leaking fuel line, pump check valve, pressure regulator or injectors.
  3. Starts, then stalls: The engine may be losing fuel pressure, ignition feed, sensor input or module control. GM’s no-start table includes P0230, P0335, P0336, PCM and communication codes, and it also notes that a malfunctioning MAF sensor can cause a no-start or stall after start.
  4. Loss of power on hills or under load: A weak pump, restricted filter, pressure regulator problem or restricted line can all be involved. GM’s fuel system diagnosis includes tests for pressure drop, return-line restriction and pressure behavior during acceleration.
  5. Loud pump noise: A new or changed whine from the tank deserves attention, but sound alone does not measure pressure.
  6. Check Engine Light: Scan the vehicle before removing parts. GM’s no-start procedure directs the technician to applicable DTC tables for several fuel, crank sensor, PCM and security-related codes.

Do not ignore security, battery and crank sensor issues. The GM procedure checks Body Control Module vehicle theft deterrent codes, engine RPM while cranking, crankshaft position sensor feed voltage, camshaft position sensor feed voltage and ignition feeds to underhood fuses. A truck with no RPM signal can crank all day with a perfectly good fuel pump fuse.

5. A practical diagnostic sequence for a driveway or small shop

Start with the least expensive checks and confirm power before replacing the pump. This is the same order used by many professional no-start charts: verify the complaint, check codes, test electrical feeds, command the pump, then measure pressure.

5. Tools that make the job more accurate:

  1. Owner’s manual and fuse cover diagram: Use them to confirm the label and amperage for your exact truck.
  2. Test light or digital multimeter: Use it to check both sides of fuses, battery voltage and grounds.
  3. OBD-II scan tool: A scan tool can read codes and, on supported vehicles, command the fuel pump ON.
  4. Fuel pressure gauge with the correct adapter: GM’s fuel system tests use a pressure gauge and, in some procedures, in-line shutoff adapters.
  5. Basic hand tools: Fuse puller, gloves, safety glasses, shop towels and a Class B fire extinguisher. GM’s service cautions call for proper ventilation, secure fuel fittings and a dry chemical Class B extinguisher during on-vehicle fuel service.
  6. Repair information for your VIN: Use it for wiring colors, connector views and pressure specifications.

6. Follow this test order:

  1. Confirm the basics. Check that the battery is charged, the engine cranks at normal speed, the tank has fuel and the fuel cap is fitted. GM’s no-start table starts with battery condition, cranking speed and adequate fuel.
  2. Scan for codes. Record all codes before clearing anything. A P0230 fuel pump circuit code is different from a crank sensor code or a theft-deterrent code.
  3. Listen for the key-on prime. Turn the key to ON without cranking. The pump may run for about two seconds. Do not cycle the key dozens of times without checking why the truck will not start.
  4. Test the fuses with the ignition ON. Probe both sides of the fuel-related and engine-control fuses. GM’s procedure checks both sides of underhood fuses with a test lamp connected to ground.
  5. Check the relay. Confirm the relay has the correct part number, is fully seated and has clean terminals. If an identical relay is available, swap it as a test, not as a permanent repair with the wrong part.
  6. Command the pump with a scan tool if possible. GM’s no-start procedure asks whether the pump operates when enabled with a scan tool; if not, it directs the technician to fuel pump electrical circuit diagnosis.
  7. Measure fuel pressure while the pump runs. For the 4.8L, 5.3L and 6.0L GMT800 no-start chart, the published range is 379–427 kPa, or 55–62 psi. For the 1999 C/K Central SFI fuel system diagnosis, GM lists 415–455 kPa, or 60–66 psi, with the pump running. Match the spec to the engine and fuel system.
  8. Watch pressure after shutdown. A quick drop can point to a check valve, regulator, injector or line leak. GM’s fuel system diagnosis includes pressure-hold tests and feed/return restrictions.
  9. Check voltage at the pump connector only after safe access. A pump with correct supply voltage and ground but no operation is a strong candidate for replacement. No voltage means the fault is upstream.
  10. Replace the pump only after the electrical circuit and pressure test support it. A new pump will not fix a bad relay feed, a broken wire, a security issue or a blocked filter.

7. Safety rules that matter on an older truck

Fuel vapor is flammable, and a 1999 truck may have brittle lines, corroded tank straps and old connectors. GM’s service information warns that the fuel pump can operate for two seconds after ignition off, requires secure fuel pipes and fittings, calls for ventilation in enclosed areas and says to place a dry chemical Class B extinguisher nearby during on-vehicle fuel service.

7. Use these precautions:

  1. Work outdoors or in a well-ventilated shop. No pilot lights, cigarettes, grinders or space heaters nearby.
  2. Wear eye protection and fuel-resistant gloves. Keep shop towels and an approved gasoline container ready.
  3. Relieve fuel pressure before opening a line. KEMSO’s replacement guide describes removing the fuel pump relay, running the engine until it stalls, cranking briefly and disconnecting the negative battery cable.
  4. Disconnect the negative battery cable before tank or wiring work. Reconnect it only after the system is assembled.
  5. Support the truck and tank correctly. KEMSO’s guide lists jack stands, a transmission jack, wheel chocks, fuel line disconnect tools, a siphon pump and an approved container for tank removal.
  6. Do not use jumper wires near fuel leaks. If you smell raw fuel or see a wet tank seam, stop the job.
  7. Get professional help for rusted lines, damaged wiring or repeated fuse failures. The cost of diagnosis is small compared with a fire or a repeat repair.

8. How to replace a blown fuse correctly

A fuse replacement is simple only when the circuit is healthy. The 1999 Silverado owner’s manual says a broken or melted silver band means the fuse should be replaced with one of identical size and rating; in an emergency, a fuse of the same amperage can be borrowed from a nonessential feature, then replaced as soon as possible.

8. Do it this way:

  1. Turn off the ignition and remove the key.
  2. Find the correct slot from the cover diagram or owner’s manual.
  3. Pull the fuse with the fuse extractor or your fingers. The instrument panel block may have an extractor mounted on the access door.
  4. Inspect both blades. Look for a broken band, melted plastic, discoloration, loose blades or corrosion in the slot.
  5. Install a fuse with the same amperage number and physical size. Do not substitute a higher rating.
  6. Turn the ignition ON and listen for the pump prime. If the new fuse opens immediately or the truck still will not start, move to circuit testing.
  7. Record what happened. A fuse that blows at key-on, during cranking, after the pump starts or only on rough roads gives a technician useful information.

9. When the fuse is good but the pump is bad

A healthy fuse, relay and power supply with low fuel pressure point toward the pump module, filter, regulator or a restriction. GM’s diagnostic flow uses a fuel pressure gauge when the pump is operating and compares the result with the specified range. GM’s fuel system diagnosis also includes restrictions in the feed or return lines, leaks and pressure-hold checks. Published guidance for 1999–2006 Vortec V8 Silverado engines commonly lists 55–62 psi, while flex-fuel applications may use 48–54 psi. Always confirm the exact engine before using a number.

9. Parts and decisions before replacement:

  1. Replace the complete in-tank module when required. KEMSO’s 1999 Silverado guide says the pump is in the tank and the module is replaced as a unit.
  2. Replace the strainer and external fuel filter when appropriate. A clogged filter can make a new pump work harder and can leave old debris in the system.
  3. Inspect the tank. Clean the top of the tank before opening it, and check for dirt, rust, water or varnish inside.
  4. Use a new sealing ring. A reused or pinched seal can cause a fuel odor or leak.
  5. Check the connector and harness. Heat, chafing and corrosion near the tank are common on an older truck. Repair damaged terminals rather than forcing a new pump to work through a weak connection.
  6. Prime and leak-check the system. KEMSO’s guide recommends several key-on cycles before starting, then checking for leaks and verifying pressure at the rail.
  7. Expect a real labor job. KEMSO estimates 2–4 hours for a DIY pump replacement and $150–$300 for a quality pump, with tank removal or bed removal required. Local shop labor, rust and fuel level can change the final cost.

10. Common mistakes that waste time and money

Most bad repairs start with replacing the most expensive part first. These are the errors to avoid on a 1999 Silverado.

10. Avoid these ten mistakes:

  1. Using a fuse chart from the wrong Silverado generation. GMT800 and GMT400 labels are different.
  2. Installing a larger fuse. The owner’s manual calls for an identical size and rating.
  3. Assuming a silent pump is a dead pump. The two-second prime depends on module command, relay, wiring and reference pulses.
  4. Ignoring the relay. The GMT800 underhood center has a separate fuel pump relay.
  5. Skipping the pressure test. GM’s no-start procedure installs a fuel pressure gauge when the pump operates.
  6. Using one pressure spec for every 1999 engine. GM documentation lists 55–62 psi for the 4.8L/5.3L/6.0L no-start test and 60–66 psi for the C/K Central SFI pump-running test.
  7. Clearing codes before recording them. Theft deterrent, crank sensor, PCM and fuel pump circuit codes lead to different tests.
  8. Forgetting the basics. Low battery voltage, slow cranking, an empty tank or a bad MAF sensor can create similar symptoms.
  9. Replacing the pump without checking voltage and ground at the connector. A wiring fault can ruin the repair.
  10. Working around fuel without ventilation, a fire extinguisher and secure fittings. GM’s cautions are direct on this point.

11. Questions owners ask before ordering parts

11. Short answers to common questions:

  1. Is the fuel pump fuse inside the cab or under the hood? For the GMT800 diagram, the 20A F58 fuel pump-related fuse and fuel pump relay are in the underhood electrical center. For the GMT400 C/K diagram, the ECM B fuse is in the underhood fuse/relay center. The truck also has an instrument panel fuse block on the driver’s side.
  2. What size fuse should I use? Use the exact rating printed on the cover, in the owner’s manual and on the original fuse. Published GMT800 and GMT400 fuel pump circuit fuses are 20A, but do not assume that every related engine-control fuse is also 20A.
  3. Can I drive with the fuel pump fuse removed? No. The engine needs fuel pressure to run.
  4. Will a bad fuse cause low fuel pressure? A blown fuse can stop the pump completely. Low pressure while the pump runs is more often a pump, filter, regulator, line or leak issue.
  5. Does a 1999 Silverado have a fuel pump reset button? Do not plan your diagnosis around one. GM’s published 1999 fuel system description focuses on the VCM-controlled relay, pump, filter, regulator and return line.
  6. Why does the pump only run for a moment? GM says the control module shuts the pump off within about two seconds if it does not receive reference pulses.
  7. Can I test the pump by applying battery power directly? Direct power testing is risky around fuel vapor and can damage wiring. Use the vehicle connector, a scan tool command and a proper electrical test procedure.
  8. Should I replace the relay with the pump? If the relay is worn, corroded or failing, replacing it is reasonable. A relay swap is a test, not proof that the pump is good.
  9. Why does the new fuse keep blowing? There is likely an overcurrent or short condition. Check the pump current draw, harness, connector and grounds before another replacement.
  10. Can a clogged fuel filter look like a bad pump? Yes. GM’s system description places an in-line filter between the pump and the injection unit, and its diagnosis includes restrictions.

12. Recommended replacement: KEMSO Fuel Pump

If testing confirms that the pump is the problem, we recommend buying a KEMSO brand Fuel Pump. KEMSO Fuel Pump products are high-performance, OEM Replacement units, and the brand states that every KEMSO fuel pump comes with a lifetime warranty. KEMSO describes its pumps as direct replacements designed to meet or exceed factory specifications, with consistent fuel pressure and flow. For a 1999 Silverado, KEMSO’s own replacement guide also recommends checking the fuse and relay before installing a new pump, and it describes the in-tank module replacement as a 2–4 hour DIY job.

Shop by year, make, model and engine, and confirm fitment with your VIN before ordering. KEMSO’s online store carries fuel pumps for cars, trucks, motorcycles, ATVs/UTVs and personal watercraft, so choosing the correct Silverado application matters. Visit https://www.kemsoracing.com/ to review specifications, product fitment and warranty details before purchase.

13. Final checklist before you call it fixed

The repair is complete only when the truck starts, holds correct pressure and has no leaks or returning codes.

  1. Recheck all fuel-related fuses and confirm the correct amperage is installed.
  2. Verify the two-second prime or scan-tool pump command.
  3. Measure fuel pressure while the pump runs using the spec for your exact engine.
  4. Check pressure hold after shutdown if the original complaint was a hard start after sitting.
  5. Inspect every fuel connection, tank seal and line for wetness or odor.
  6. Clear codes only after recording them, then road-test the truck. Watch for hesitation on hills, hot restarts and stalling.
  7. Rescan for P0230, P0087 and other returned codes if the Check Engine Light comes back.
  8. Keep the receipt, part number and warranty information.

For replacement parts, fitment details and warranty information, visit https://www.kemsoracing.com/.