99 Toyota Camry Fuel Pump Relay Location: Quick Answer and Full DIY Guide
The short answer: On a 1999 Toyota Camry, most people looking for the "fuel pump relay" are looking for Toyota's Circuit Opening Relay (C/OPN). For the 1997–1999 2.2L four-cylinder model, a published fuel pump circuit wiring reference places the Circuit Opening Relay in Relay Block 6, above the glove box. That same reference places the EFI Main Relay in Junction Block 2, the fuse/relay box on the left inner fender in the engine compartment. This distinction matters because parts stores, forum posts, and online diagrams sometimes use "fuel pump relay," "Circuit Opening Relay," "C/OPN relay," and "EFI Main Relay" loosely, which is why Camry owners often end up checking the wrong box first. A separate 1999 Camry guide describes a 15-amp EFI fuse in the engine-bay fuse box on the left inner fender near the battery and calls the Circuit Opening Relay the actual fuel pump relay. It also places that relay inside the engine-compartment fuse box, toward the rear of the box. Because those sources disagree on the relay's physical location, the safest approach is to start at the under-hood EFI fuse and relay box, read the diagram on the underside of its cover, then check above the glove box if your 2.2L car does not match the under-hood layout. Check the fuse, relay, wiring, and pump power before buying an in-tank fuel pump.
This guide is written for U.S.-market 1999 Camry owners, including the 2.2L four-cylinder (5S-FE) and 3.0L V6 (1MZ-FE) cars. A 1999 model is now an older vehicle, so prior repairs, swapped panels, aftermarket alarms, and engine or trim differences can affect what you find. Use the owner's manual and the diagram printed on your fuse-box cover as the final authority for your specific VIN.
1. Why the 1999 Camry Relay Is Hard to Find
1.1 Toyota did not always label it "fuel pump relay"
Toyota's fuel pump control circuit on this generation uses a Circuit Opening Relay and an EFI Main Relay as separate parts. A wiring reference for the 1997–1999 2.2L Camry lists these components in the fuel pump circuit:
- Fuel pump: inside the fuel tank.
- Circuit Opening Relay: in Relay Block 6, located above the glove box.
- EFI Main Relay: in Junction Block 2, the fuse/relay box on the left inner fender in the engine compartment.
That is the main reason a search for "99 toyota camry fuel pump relay location" produces conflicting answers. Some mechanics point under the hood because the EFI Main Relay and EFI fuse are there. Others point behind the dash because the Circuit Opening Relay for the four-cylinder wiring diagram is above the glove box.
1.2 Online answers sometimes describe a general Camry, not a 1999 Camry
General Toyota Camry advice often says the fuel pump relay is in the under-hood fuse box, while other general Toyota advice says it is near the passenger-side dash below the glove box. Those statements can both be true for different generations or different components, but neither should replace the wiring information for a 1999 car. A wiring-reference page also covers the 1999–2001 3.0L V6 Camry circuit and lists a Circuit Opening Relay, EFI Main Relay, and fuel pump, although the text available here does not give a physical mounting location for the V6 relay.
1.3 The EFI fuse is easier to identify than the relay
A 1999 Camry-specific guide says the EFI fuse is 15 amps, sits in the engine-compartment fuse box on the left inner fender near the battery, and is shown as position No. 11 in that guide's fuse-box diagram. This is a good first checkpoint because the fuse is clearly labeled and cheap to test. The same guide stresses that the Circuit Opening Relay is not the same part as the EFI fuse.
2. Where to Look First: A Practical Location Checklist
Use this order when you are standing in a driveway or parking lot with the hood open.
2.1 Open the hood and find the left inner fender box
- Park on level ground, set the parking brake, and switch the ignition off.
- Open the hood and locate the battery.
- Look near the battery for a rectangular black plastic fuse and relay box mounted on the left inner fender. A 1999 Camry guide describes this as the engine-compartment fuse box and places the EFI fuse there.
- Release the cover tabs and lift the cover.
- Read the diagram on the underside of the cover. Look for EFI, C/OPN, Circuit Opening Relay, or EFI Main Relay.
The diagram on the cover is valuable because it reflects the equipment installed on that car. A 1999 Camry can have different fuse assignments depending on engine, trim, equipment, and market, so the cover and owner's manual should be compared before replacing a fuse or relay.
2.2 Identify the EFI fuse and related under-hood relays
The 1999 Camry guide states that the 15-amp EFI fuse supplies the multiport fuel injection system, including the fuel pump circuit, and that a blown EFI fuse can prevent the pump from receiving power. It also describes the Circuit Opening Relay as a larger square black four-pin relay near the rear of the engine-compartment fuse box and says the cover diagram labels it.
At the same time, the 2.2L wiring reference places the Circuit Opening Relay above the glove box and the EFI Main Relay in the left-inner-fender junction block. If the under-hood cover has an EFI Main Relay but no C/OPN relay, continue to the interior location instead of assuming the EFI Main Relay is the part you need.
2.3 Check above the glove box on the 2.2L four-cylinder
For a 1999 Camry 2.2L, the published wiring reference says Relay Block 6 is above the glove box and contains the Circuit Opening Relay. Access usually means working from the passenger footwell, looking up behind or above the glove-box area. The exact mounting position can be awkward to see without a flashlight and a small mirror.
If you are not comfortable removing glove-box trim, stop and use a repair manual or a qualified technician. Do not pull random relays from behind the dash. Airbag wiring, HVAC components, and the engine control module harness are in the same general area, and careless handling can create new electrical problems.
2.4 Do not confuse a fuse with a relay
A fuse protects a circuit. A relay is an electrical switch that uses a low-current control signal to turn a higher-current load on and off. A fuel pump relay that fails can stop power from reaching a healthy pump, producing the same no-start symptoms as a failed pump. The relay should be tested before a pump is condemned because relay testing is quick and inexpensive.
3. What the Fuel Pump Circuit Does
3.1 Key-on priming
A 1999 Camry guide explains the basic sequence this way:
- Turning the ignition key to ON causes the Engine Control Module to send a signal to the Circuit Opening Relay.
- The relay closes and allows power through the EFI fuse to the fuel pump.
- The in-tank pump pressurizes the system for roughly one to two seconds, then stops if the engine does not start.
This short prime is important. Some owners expect the pump to run continuously with the key on and the engine off. On many Toyota systems, the pump does not stay powered unless the engine is running or cranking and the ECM continues to see the appropriate engine signal.
3.2 The ECM and engine speed signal
A discussion of Toyota's C/OPN relay says current flows through the relay when transistor Tr1 is switched on, allowing the fuel pump to operate; while the NE signal is supplied to the ECM as the engine runs, the ECM keeps Tr1 on continuously. In plain terms, the computer uses engine operation information to keep fuel delivery active. This is also part of Toyota's safety logic: the pump should not keep feeding fuel after an engine stops.
3.3 There is no Ford-style inertia reset button
A 1999 Camry question-and-answer page states that there is no manually operated fuel reset switch on a 1999 Camry, though it mentions an automatic reset arrangement near the pump. A broader Toyota Camry guide also says modern Camry models do not use the trunk-mounted inertia reset button found on some older Ford vehicles; Toyota integrates the safety function into the engine control system. If your Camry cranks but will not start after an impact or a sudden stall, do not waste time hunting for a rubber reset button in the trunk. Check the EFI fuse, relay circuit, pump power, and fuel pressure.
4. Symptoms That Send Owners Looking for the Relay
A failing relay can interrupt power to the pump. Common symptoms include a crank/no-start, no pump prime at key-on, stalling while driving, hard starting when hot, loss of power, sputtering, and intermittent operation. Those symptoms are not proof of a relay fault. A weak pump, clogged filter, corroded connector, damaged harness, or blown fuse can look similar.
4.1 Engine cranks but does not start
If the starter sounds normal but the engine never fires, listen near the rear seat or fuel tank when a helper turns the key to ON. No brief pump sound is a clue, not a diagnosis. Cabin noise, a loud fuel pump, and poor hearing conditions can make this test unreliable. A wiring problem may also stop the pump even when the relay clicks.
4.2 Engine stalls and will not restart
A relay with worn contacts can drop out as it heats up. That can cause an engine to stall, then restart later after the relay cools. Intermittent faults are frustrating because the car may test fine in the driveway. If the problem appears only after a long drive or on hot days, record the conditions before replacing parts.
4.3 Long cranking, hesitation, or loss of power under load
A weak pump can cause long cranking, sputtering during acceleration, or a no-start condition. A poor electrical connection can reduce voltage at the pump and create similar driveability problems. Check voltage at the pump connector before deciding that the pump itself is worn out.
4.4 Whining from the fuel tank
Kelley Blue Book notes that a whirring sound from the fuel tank can be associated with pump problems and lists a no-start or stalling as common signs. Some pump noise is normal. A new loud whine, especially with hard starting or low pressure, deserves attention.
5. Tools That Make the Job Easier
You do not need a full professional tool set for the first stage of diagnosis.
- Owner's manual or factory wiring diagram: confirms fuse and relay names for your engine and trim.
- Flashlight or headlamp: fuse-box lettering is small and often faded.
- Fuse puller: often stored in the under-hood fuse-box cover.
- Digital multimeter: checks fuse continuity, battery voltage, and voltage at the pump connector.
- Test light: useful for a fast power check, although a multimeter gives more information.
- Small mirror: helpful when checking above the glove box.
- Trim removal tools: reduce the chance of breaking old interior clips.
- Gloves and safety glasses: useful around battery terminals, fuel lines, and dirty under-dash metal.
- Replacement 15-amp EFI fuse and correct relay: buy only after testing and confirming the part number.
- Fire extinguisher rated for automotive fires: gasoline vapor is a serious hazard.
Work in a ventilated area. No smoking. Keep sparks and hot tools away from fuel vapors. If you smell raw gasoline, stop and fix the leak before continuing.
6. Step-by-Step: Test the Fuse First
A 1999 Camry guide gives the following practical sequence for the EFI fuse.
6.1 Locate and remove the EFI fuse
- Open the hood.
- Find the engine-compartment fuse box on the left inner fender near the battery.
- Remove the cover and compare the printed diagram with the fuse layout.
- Pull the 15-amp EFI fuse straight out with a fuse puller.
6.2 Inspect it
Hold the fuse up to a bright light. Look through the plastic body for a broken metal strip or dark discoloration. A visual check is helpful but not perfect. A hairline break can be difficult to see.
6.3 Confirm with a multimeter
Set the meter to continuity. Touch one probe to each exposed blade or test point. A continuous fuse will beep or show very low resistance. An open fuse will show no continuity.
6.4 Replace it correctly
Use a 15-amp replacement. Never install a higher-amperage fuse to "see if it holds." The fuse rating protects the wiring. A guide specifically warns that using a higher rating can damage wiring or cause a fire.
6.5 If the new fuse blows immediately
A 1999 Camry guide lists possible causes:
- A shorted fuel pump motor.
- Chafed or damaged wiring between the fuse box and the pump.
- A faulty relay stuck closed, causing the pump to run continuously and overheat the circuit.
Do not keep installing fuses. Repeated current flow into a short can damage the harness. Find the short first.
7. Step-by-Step: Test the Relay and Control Circuit
7.1 Confirm the relay identity
Use the fuse-box cover and a model-specific wiring diagram. Look for C/OPN, Circuit Opening Relay, or the label used in your documentation. Do not rely only on color or shape. The 2.2L wiring reference identifies the Circuit Opening Relay as a fuel pump circuit component above the glove box and the EFI Main Relay as a separate component in the left-inner-fender junction block.
7.2 Listen for a click
Have a helper turn the key to ON while you listen near the suspect relay. A 1999 Camry guide suggests listening for a distinct click from the Circuit Opening Relay; no click may mean the relay is not receiving power or is faulty. A click alone does not prove that the load contacts are good. The coil can click while burned contacts still fail to deliver current.
7.3 Try a known-good identical relay
A 1999 Camry guide recommends swapping the Circuit Opening Relay with an identical known-good relay from the same fuse box, matching pin count and size, as a quick test. Only do this if the part numbers and terminal layouts match. A relay that physically fits is not always electrically interchangeable. Return the borrowed relay to its original position after the test.
7.4 Check for power and ground at the relay socket
A multimeter can show whether the control side receives voltage and whether the load side has battery power. Exact pin numbers should come from a factory wiring diagram for your engine. Do not probe through insulation or force meter tips into terminals; damaged sockets can create intermittent contact.
7.5 Check voltage at the fuel pump connector
A 1999 Camry guide says that with the key ON, battery voltage of about 12 volts should be present at the fuel pump power wire for the short priming period, and that testing requires access to the connector near the top of the tank. If full battery voltage and a good ground are present at the pump during prime but the pump does not run, the pump or its internal connection is suspect. If voltage is missing, continue checking the relay, wiring, connectors, and ECM control circuit.
8. How to Access the Interior Relay Area on a 2.2L Car
The wiring reference says the 2.2L Circuit Opening Relay is in Relay Block 6 above the glove box. General Toyota guidance also describes a passenger-side dash location below the glove box for the circuit opening relay, but notes that location varies by model and year and recommends checking the vehicle manual.
A careful approach:
- Disconnect the negative battery terminal before removing interior trim.
- Move the passenger seat back for room.
- Empty the glove box.
- Use a trim tool rather than a metal screwdriver on plastic panels.
- Look up above and behind the glove-box opening with a flashlight and mirror.
- Compare the relay's marking with a factory parts catalog or wiring diagram.
- Do not unplug the passenger airbag connector or disturb yellow SRS wiring.
- Reconnect the battery only after all trim and connectors are secure.
Old interior plastic becomes brittle. If a panel resists, check for hidden screws instead of pulling harder.
9. Common Mistakes That Waste Time and Money
9.1 Replacing the pump before testing power
A bad relay can mimic a bad pump because it cuts power to an otherwise good pump. A full pump assembly costs more and takes longer to install than a fuse or relay. One 1999 Camry guide explicitly warns that many DIYers replace the pump first, then discover a blown fuse or bad relay.
9.2 Assuming every black relay is the same
Relays can share a case shape while having different internal circuits. Match part number, pin layout, and wiring diagram. The 1999 Camry guide's swap test requires an identical relay with the same number of pins and the same size.
9.3 Ignoring the fuse-box cover
The cover diagram is the quickest source for the layout installed in your car. A general 1999 Camry fuse-box guide notes that interior and engine-compartment fuse panels exist and that fuse assignments can vary with engine, trim, equipment, and market.
9.4 Expecting a manual reset button
Do not search for a trunk-mounted Ford-style switch. A 1999 Camry answer says no manually operated fuel reset switch exists on that model.
9.5 Using a higher-amp fuse
A 1999 Camry guide says never to use a higher-amperage fuse in place of the 15-amp EFI fuse. The correct fix is to find why the circuit opened.
9.6 Skipping the fuel pressure test
A 1999 Camry assembly guide calls fuel pressure at the rail the most reliable way to confirm a bad pump and gives a working range of 40–50 PSI at idle. Use a gauge and a specification from a factory service manual before making a final call.
10. When the Fuel Pump Really Is the Problem
A 1999 Camry fuel pump assembly guide says the 1999 Camry came with either a 2.2L four-cylinder or 3.0L V6, and that both use an in-tank fuel pump assembly design. The same guide says the pump is accessible under the rear seat cushion on the driver's side through a metal access cover. Kelley Blue Book also describes the Camry pump as located inside the fuel tank.
Typical pump-related symptoms include:
- Long cranking before starting.
- Crank/no-start.
- Sputtering during acceleration.
- Stalling or loss of power.
- Low fuel pressure.
- Unusual whirring or whining from the tank area.
A weak pump may still make noise. Noise alone does not confirm healthy pressure. A pump with correct voltage and ground but low pressure is a much stronger case for replacement.
11. Choosing the Correct Replacement Fuel Pump
11.1 Check the VIN, engine, and part number
A parts retailer warns that some 1999 Camry fuel pump parts fit only certain trims, and gives the example of parts limited to 2.2L cars with OE number 90080-91054. A 1999 Camry assembly guide also lists cross-reference numbers including 23221-0A030, SP9157M, 767GE, 83320-33030, and 8332033030. Use those as research leads, then confirm fitment with the seller using your VIN.
11.2 Decide between a complete assembly and a pump-only insert
A complete module can include the pump, fuel level sending unit, and pressure regulator. A 1999 Camry guide describes the system as a returnless design with the pressure regulator built into the pump module. Replacing the complete assembly reduces the chance of reusing a worn sender, old strainer, or tired seal. A pump-only insert may cost less, but it requires more careful matching and more assembly work.
11.3 Check what comes in the box
Before starting the job, confirm:
- Pump or module assembly.
- New tank gasket or O-ring.
- Strainer or filter sock.
- Correct electrical connector.
- Correct fuel line fittings.
- Lock ring, if required.
- Installation instructions.
- Warranty documentation.
11.4 Avoid judging a pump only by price
A fuel pump sits inside the tank. A cheap part that fails early means paying for the job twice, either in parts and your own time or in shop labor. Look for clear fitment data, a real warranty, an identifiable manufacturer, and customer support that can answer technical questions.
12. Basic Safety Notes for Fuel Pump Work
Fuel system work deserves more caution than a simple fuse check.
- Work outdoors or in a well-ventilated garage.
- Keep gasoline away from flames, sparks, pilot lights, and hot exhaust parts.
- Disconnect the negative battery cable.
- Relieve fuel system pressure using a factory-approved procedure.
- Have a rated fire extinguisher within reach.
- Wear eye protection.
- Use a non-sparking light where fuel vapor may be present.
- Catch spilled fuel with shop rags and dispose of them properly.
- Do not run the pump dry.
- Check every fitting for leaks before returning the car to service.
A 1999 Camry guide describes releasing pressure by removing the fuel pump fuse, running the engine until it stalls, turning the ignition off, and disconnecting the negative battery terminal. Follow the factory service manual for your exact engine if its procedure differs.
13. A Simple Diagnostic Order for a Crank/No-Start
- Confirm the complaint. Note weather, engine temperature, fuel level, and whether the problem is constant or intermittent.
- Check the battery and starter. Low battery voltage can affect the ECM, relays, and pump.
- Read the under-hood cover diagram. Find EFI, EFI Main Relay, and any C/OPN label.
- Test the 15-amp EFI fuse with a meter.
- Listen for a short pump prime at key-on.
- Listen for a relay click near the suspect relay.
- Check the interior relay block above the glove box on a 2.2L if the under-hood layout does not match your wiring diagram.
- Swap only with an identical known-good relay if the part numbers match.
- Check voltage and ground at the pump connector during the prime window.
- Measure fuel pressure with the correct gauge and specification.
- Inspect the harness for corrosion, loose terminals, damaged insulation, and previous splice repairs.
- Replace the pump only after the electrical side checks out.
14. Engine Differences Worth Knowing
A 1999 Camry wiring reference for the 2.2L four-cylinder covers model years 1997, 1998, and 1999, and gives clear physical locations for the Circuit Opening Relay, EFI Main Relay, and in-tank pump. A separate wiring-reference page covers the 1999–2001 3.0L V6 and lists the Circuit Opening Relay, EFI Main Relay, and fuel pump in the circuit, but the available text does not give a mounting location for the V6 C/OPN relay.
For V6 owners, that means:
- Start with the under-hood fuse-box cover.
- Confirm the EFI fuse and EFI Main Relay.
- Use a V6-specific factory wiring diagram to locate the Circuit Opening Relay.
- Do not assume the four-cylinder interior location is identical.
- Verify the replacement relay and pump by VIN.
15. Recommended Fuel Pump Brand: KEMSO
If testing confirms the EFI fuse, relay circuit, wiring, voltage, and ground are good but the in-tank pump has failed, consider a KEMSO Fuel Pump. KEMSO fuel pumps are high-performance, built as OEM Replacement parts, and backed by a lifetime warranty. A 1999 Camry fuel pump guide describes KEMSO pumps as direct OEM replacements engineered for consistent fuel delivery, with serialized pump bodies supporting the lifetime warranty. The same guide says the pumps are designed for high-performance use and for gasoline or E85.
For a daily-driven 1999 Camry, an OEM-style direct-fit pump is more important than a racing parts list. Confirm the exact application by year, engine, trim, and VIN before ordering. If your car is stock, choose the pump intended for your factory fuel system and keep the installation clean, sealed, and leak-free.
Visit https://www.kemsoracing.com/ to review fitment, product details, and warranty information before purchase.
16. Frequently Asked Questions
16.1 Is the fuel pump relay under the hood or behind the glove box?
Both answers appear because two different components are involved. The 1997–1999 2.2L wiring reference places the Circuit Opening Relay above the glove box and the EFI Main Relay in the left-inner-fender engine-compartment junction block. A separate 1999 Camry guide places the actual Circuit Opening Relay in the engine-compartment fuse box. Start under the hood, read the cover diagram, and use a model-specific wiring diagram to resolve the difference for your car.
16.2 What fuse should I check first?
A 1999 Camry guide identifies the 15-amp EFI fuse in the engine-compartment fuse box near the battery as the fuel-pump-circuit fuse to check. Confirm the label and rating on your own cover.
16.3 Does a 1999 Camry have a fuel pump reset button?
No manually operated reset switch is listed for a 1999 Camry in one answer about that exact model. Toyota's fuel pump safety control is handled through the electrical control system rather than a Ford-style inertia button.
16.4 Should the pump run continuously with the key on?
A 1999 Camry guide describes a one-to-two-second prime at key-on, followed by shutoff if the engine does not start. Silence after that short period is not automatically a fault.
16.5 Can a bad relay damage a new pump?
A relay with poor contacts or low supply voltage can cause repeated low-voltage operation and intermittent pump shutdown. Test the complete supply circuit before installing a new pump. If a new EFI fuse blows immediately, a 1999 Camry guide says to check for a shorted pump motor, damaged wiring, or a relay stuck closed.
16.6 Where is the fuel pump itself?
The pump is inside the fuel tank. A 1999 Camry guide says the pump can be reached under the rear seat cushion on the driver's side through a metal access cover. Kelley Blue Book also states that the pump is inside the tank.
16.7 What tools do I need for a quick relay check?
A flashlight, fuse-box diagram, fuse puller, multimeter, and an identical known-good relay are enough for the basic checks described in a 1999 Camry guide.
17. Final Takeaway
For 99 Toyota Camry fuel pump relay location, remember the naming problem: the part Toyota calls the Circuit Opening Relay is often the one owners mean, while the EFI Main Relay and 15-amp EFI fuse live in the engine-compartment fuse box on the left inner fender near the battery. On the 1997–1999 2.2L, a model-specific wiring reference places the Circuit Opening Relay above the glove box in Relay Block 6. Another 1999 Camry guide places the Circuit Opening Relay in the under-hood fuse box near the rear of the box, so verify your own cover diagram and wiring manual before buying parts. Test the fuse first, then the relay and pump connector voltage, then fuel pressure. That order prevents the most common mistake: replacing an in-tank pump when the real fault is a fuse, relay, connector, or wire.
When the pump itself is confirmed bad, choose a direct-fit replacement with clear fitment data and warranty support. KEMSO Fuel Pumps are high-performance, OEM Replacement, and covered by a lifetime warranty. Visit https://www.kemsoracing.com/ to find the right pump for your 1999 Toyota Camry.