Aeromotive 11542 Fuel Pump: Specs, Fit, Install, and Buying Guide

The Aeromotive 11542 fuel pump is a 340 LPH, in-tank, electric Stealth 340 pump made for gasoline and E85, with an offset inlet located in line with the outlet. It is a strong choice when a stock pump cannot support a turbo, supercharger, larger injectors, or an ethanol setup, but it is not a universal bolt-in part for every car. Before buying, confirm the pump body style, inlet position, outlet size, fuel type, pressure needs, wiring, and your vehicle’s hanger assembly. Aeromotive lists 11542 as an in-tank 340 LPH pump with an offset inlet and an applications guide for checking vehicle fit; some retailers also list it as replacing part number 11142.

For most U.S. buyers, the practical decision is simple: choose 11542 when your build needs more fuel flow than the factory pump can deliver and your existing pump module accepts this pump shape. Choose a complete vehicle-specific module assembly when you want a simpler replacement. Choose a lower-flow OEM-style pump when the engine is stock and you only need to restore normal operation. If the pump is being installed with an Aeromotive tank or pump assembly, follow the fuel line size, post-filter, rollover valve, and AN fitting instructions in the supplied manual, because those details affect both safety and pump life.

1. What the Aeromotive 11542 Fuel Pump Is

1.1 Product identity

Aeromotive part number 11542 belongs to the company’s Stealth 340 in-tank electric fuel pump line. Aeromotive describes it as a high-output pump for popular EFI applications, with an offset inlet that is in line with the outlet. The part is also sold as AER11542 or AEI-11542 by retailers, and Aeromotive’s own listing identifies the part number as 11542.

1.2 Main published specifications

The core published figures are consistent across manufacturer and retailer listings:

Flow: more than 340 liters per hour at 40 psi, also listed as 90 gallons per hour.
Fuel: gasoline and E85 compatibility are listed by multiple sources; diesel and methanol are not listed as compatible in one retailer’s specification table.
Mounting: in-tank electric pump, designed to bolt into many existing hanger assemblies.
Inlet: offset inlet, in line with the outlet.
Outlet: retailer listings show a 0.362 inch or 5/16 inch outlet, and one listing describes a hose barb style.
Electrical: 12 volts.
Body: some sellers describe an OEM-style 39 mm body.
Included parts: listings mention a universal filter sock and an install kit, while Summit Racing lists no sending unit and no fuel pressure regulator included.

1.3 What “Stealth 340” means in real use

The number 340 points to the flow class, not a horsepower rating that applies to every engine. Aeromotive’s horsepower chart varies by fuel system, fuel type, and power adder. Its published table lists up to 1,000 hp for carbureted naturally aspirated gasoline, 850 hp for carbureted forced induction gasoline, 850 hp for EFI naturally aspirated gasoline, and 700 hp for EFI forced induction gasoline. With E85, the listed maximums are lower: 700 hp for carbureted naturally aspirated, 595 hp for carbureted forced induction, 595 hp for EFI naturally aspirated, and 490 hp for EFI forced induction.

These numbers are planning figures for one pump under the listed conditions. They are not a promise for every car. Real results depend on base fuel pressure, boost pressure, line size, filter condition, injector size, voltage at the pump, regulator setup, and tuning.

2. When This Pump Makes Sense

2.1 A stock replacement may not be enough

Many factory fuel pumps are sized for factory power. When you add forced induction, increase injector size, switch to E85, or raise the rev limit, fuel demand can rise. The engine may still idle normally and drive well at light throttle, then lose pressure under load. That is the point where a higher-output in-tank pump becomes useful.

Aeromotive says the 340 Stealth is intended for applications requiring more flow while retaining factory lines and mounting provisions available in the original equipment hanger assembly. That makes the pump attractive to owners who want more capacity without building a completely new fuel system.

2.2 Common upgrade situations

1. Turbo or supercharger builds: Boost raises fuel pressure demand at the injector. The pump must maintain flow at higher system pressure, not only at free flow.
2. E85 conversions: Aeromotive’s published horsepower table shows reduced maximum horsepower figures on E85 compared with gasoline.
3. Larger injectors: Injectors need stable pressure to deliver the commanded fuel.
4. Older performance cars: Owners often want more flow while keeping the factory tank and hanger.
5. Track use: Sustained high load can expose weak voltage, clogged filters, poor wiring, or a tired pump.

2.3 When not to buy it

Do not buy 11542 only because it has a high flow number. A stock daily driver with no tuning changes usually does not need it. A very high horsepower E85 build may need more pump capacity, larger lines, a stronger electrical supply, or a different fuel system layout. A vehicle with a sealed plastic module may require a complete module assembly rather than a bare pump. A carbureted conversion also needs the correct regulator, return line, filtration, and safe routing.

3. Fitment: The Step Most Buyers Get Wrong

3.1 “Fits many hanger assemblies” does not mean “fits all vehicles”

Aeromotive’s wording is specific: the compact pump bolts into many existing hanger assemblies, and the company directs buyers to an applications guide. That is not the same as guaranteed fitment by year, make, and model. Retailers also label the pump as universal or as a drop-in upgrade for many OE applications, but the inlet layout still matters.

3.2 Check the inlet layout

P/N 11542 is listed as offset inlet, inline with outlet. If your factory pump uses a center inlet, a different bottom shape, or a different pickup location, the pump may not sit correctly in the module. That can cause fuel pickup problems at low tank levels, poor sealing, or an installation that never feels secure.

3.3 Check the pump body and bracket

One seller describes a 39 mm OEM-style body. Before ordering, measure the old pump body, compare bracket diameter, and look at the height from the pickup sock to the outlet. Compare those measurements with the listing photos and the vehicle application information. Do this before opening the fuel tank, because a wrong pump can leave the car disassembled while you wait for the correct part.

3.4 Check the outlet connection

Published listings show a 0.362 inch outlet on some pages and 5/16 inch on others; one listing also describes a 3/8 inch hose barb outlet. Sizes may be rounded differently by sellers, so use the Aeromotive part number, installation sheet, and your actual hose or module connection to confirm the fit. Do not force a hose onto a fitting. Fuel connections must seal correctly and remain secure under pressure.

3.5 Check the electrical connector

The pump is a 12-volt electric unit. Some installations require connector changes, wiring upgrades, or a proper fuel pump relay and harness. Poor voltage at the pump can reduce flow even when the pump itself is in good condition. If the factory wiring is old, overheated, corroded, or modified, inspect it before blaming the new pump.

4. Flow, Pressure, and Power: How to Read the Numbers

4.1 Flow at 40 psi is not the whole story

The headline figure is more than 340 LPH at 40 psi, described by Aeromotive as over 30 percent more flow than other popular aftermarket pumps at that pressure. That is useful information, but fuel pressure changes under boost and with regulator settings. Always look at the pump’s performance across the pressure range your engine will actually use.

4.2 EFI and carbureted systems are different

Fuel injection commonly uses higher base pressure than a carburetor. Return-style systems, returnless systems, pulse-modulated controls, and carbureted regulators all place different demands on the pump. Aeromotive’s official horsepower table splits ratings by CARB or EFI, power adder, and fuel type. Use that table as a starting point, then confirm the plan with your tuner or fuel system supplier.

4.3 Horsepower claims need context

A retailer description says the 340 Stealth can support up to 1,000 hp carbureted naturally aspirated on gasoline, 850 hp carbureted forced induction on gasoline, 850 hp EFI naturally aspirated on gasoline, 700 hp EFI forced induction on gasoline, and lower figures with E85. The same figures appear in Aeromotive’s published chart. A safe build leaves margin. If your target is close to the upper number, the rest of the fuel system needs careful review.

4.4 E85 requires extra planning

E85 compatibility is listed for 11542, but E85 often requires more fuel volume than gasoline. Aeromotive’s chart reflects this with lower maximum horsepower figures on E85. If you run E85, check injector duty cycle, fuel line size, filter rating, pump wiring, and tune. Also consider how often the vehicle sits, because fuel quality and storage habits matter.

5. Installation Planning

5.1 Tools and supplies to have ready

Have the Aeromotive instructions, a service manual for your vehicle, a fuel pressure gauge or scan tool capable of reading fuel pressure where applicable, new hose or sealing parts as needed, correct AN fittings if your system uses them, a clean work area, a fire extinguisher rated for fuel fires, eye protection, gloves, and a container approved for gasoline. Work outdoors or in a well-ventilated shop. Avoid sparks, open flames, and hot work surfaces.

5.2 Safety before tank access

1. Relieve fuel system pressure following the vehicle service procedure.
2. Disconnect the battery before working on wiring or the pump module.
3. Lower fuel level when possible. A full tank is heavy and increases spill risk.
4. Keep the area ventilated. Fuel vapor is hazardous.
5. Do not use incandescent drop lights or tools that can spark near the tank opening.

5.3 Remove and inspect the old parts

Clean the area around the tank opening before removing the module. Dirt that falls into the tank can clog the new filter sock or post-filter. Inspect the old sock, the inside of the tank, the hanger, the wiring, and the connector. If the tank has rust, sediment, or old fuel contamination, address that before installing a new pump.

5.4 Compare parts before installation

Set the old pump beside the new pump. Check inlet position, body diameter, outlet shape, length, wiring terminals, and mounting method. Install the supplied filter sock and kit parts only if they match your hanger and tank depth. A sock that sits too high, too low, or against the tank wall can cause fuel starvation.

5.5 Electrical connections

Use a secure connection with correct polarity. Loose terminals create heat and voltage drop. Route wiring away from exhaust, moving suspension parts, and sharp edges. If your build uses higher current than the factory circuit was designed for, install a proper relay and power circuit with the correct fuse and wire gauge. Do not twist wires together and cover them with tape.

5.6 Filtration and fittings

Aeromotive’s tank and pump assembly instructions for systems using the Stealth 340 recommend AN-06 EFI or AN-08 carb high-pressure fuel lines, fittings, and O-rings, along with a 10 micron post-filter such as P/N 12301 or 12321. Those instructions also state that the tank assembly feed, return, and vent ports use O-ring sealed AN-06 style connections and are not pipe thread; thread sealant should not be used on those ports. Follow the manual for your exact tank or hanger. Do not assume every fitting on every vehicle uses the same sealing method.

5.7 First start and leak check

Before starting the engine, cycle the pump several times if the vehicle allows it, then inspect every connection. Confirm fuel pressure. Start the engine and check again while it idles. If pressure is low, noisy operation changes, or the engine hesitates under load, stop and diagnose. Do not keep driving with unstable pressure.

6. Common Problems After Installation

6.1 Low fuel pressure

Check the filter, pump voltage, ground, regulator, hose restrictions, pickup sock position, and fuel level. A new high-flow pump cannot overcome a clogged filter, weak wiring, or a kinked line. Confirm pressure with a reliable gauge or data source before replacing more parts.

6.2 Pump noise

Some in-tank pumps are audible, especially outside the car or with a low fuel level. Loud buzzing, whining that changes sharply, or noise combined with pressure loss deserves inspection. Check mounting isolation, tank contact, sock position, and voltage.

6.3 Fuel starvation in corners or at low tank level

This often points to pickup position, baffling, or a sock that does not sit correctly. Make sure the pump and filter sock are located where the module was designed to hold fuel. If the vehicle sees track use, consider whether the factory tank baffling is adequate.

6.4 Hard starting

Look for pressure bleed-down, check valves, regulator behavior, injector leakage, and wiring during key-on. Hard starting after a pump swap is not always a pump defect.

6.5 Tuning problems

A higher-capacity pump does not replace a correct tune. If the engine was tuned around a failing pump, injector data, fuel pressure, and load calculations should be checked after the fuel system is repaired. Forced induction and E85 builds should be verified by a qualified tuner.

7. Maintenance Habits That Protect the Pump

1. Replace or inspect filters on schedule. A restricted filter makes the pump work harder.
2. Avoid running the tank very low. In-tank pumps rely on fuel around the pump for cooling and consistent pickup.
3. Keep the tank clean. Sediment and rust shorten pump life.
4. Use compatible fuel. Listings for 11542 state gasoline and E85 compatibility; one specification table lists diesel and methanol as not compatible.
5. Maintain wiring and grounds. Heat, corrosion, and loose connectors reduce voltage.
6. Check pressure after other fuel system work. Any change to injectors, regulator, lines, or tuning should be followed by a pressure check.

8. Aeromotive 11542 vs. Other Pump Choices

8.1 Versus a stock OEM replacement

A stock-style pump usually focuses on factory fit and factory flow. It is the right choice for many unmodified vehicles. The 11542 is aimed at higher flow while using many existing hanger assemblies. If your engine is stock, extra flow is not automatically better; the regulator and return system still have to manage it.

8.2 Versus a complete module assembly

A module assembly may include the sending unit, bucket, jets, regulator, and vehicle-specific connections. Summit Racing’s listing for 11542 says no sending unit and no regulator are included. If your original module is cracked, the fuel level sender is bad, or the wiring connector is brittle, a complete assembly may save labor and reduce risks.

8.3 Versus other 340 LPH pumps

The 11542’s published advantage is strong flow at 40 psi and a compact body that fits many existing hangers. When comparing other 340 LPH pumps, check inlet layout, body diameter, outlet style, pressure curve, fuel compatibility, included kit parts, warranty, and support. Do not compare only the biggest number on the box.

8.4 Versus external inline pumps

An external pump can suit custom race fuel systems, but it adds plumbing, mounting, noise, and exposure. The 11542 stays in the tank and is intended to work with many factory-style mounting provisions. For a street car, that can be simpler and cleaner.

9. U.S. Buyer Checklist

1. Confirm the part number. Look for 11542, AER11542, or AEI-11542, and match the Aeromotive description.
2. Confirm inlet layout. This part is offset inlet, in line with outlet.
3. Confirm vehicle fit. Use the manufacturer applications guide and your own module comparison.
4. Confirm fuel type. Published listings state gasoline and E85 compatibility.
5. Confirm pressure and flow needs. Use Aeromotive’s horsepower chart as a planning reference.
6. Confirm wiring condition. The pump is 12 volts, and voltage at the pump matters.
7. Confirm filtration. Aeromotive tank assembly instructions call for a 10 micron post-filter in that setup.
8. Confirm emissions and road-use rules. Some performance parts listings carry EPA or California warnings and may not be legal for use on public roads or highways. Check local rules before installation.

10. Practical Buying Advice

10.1 Buy from a source that provides full part details

Choose a seller that lists the exact part number, inlet style, fuel compatibility, included kit contents, return policy, and support contact. Product pages that only show a generic photo can lead to mistakes.

10.2 Do not ignore the install kit

Listings mention a universal filter sock and install kit, but universal does not mean every piece will match every vehicle. Compare the parts with your module before discarding the old hardware.

10.3 Budget for related parts

A pump upgrade may also require a post-filter, hose, clamps or AN fittings, wiring connector, relay harness, tank seal, pressure gauge use, and tuning. Planning for these items upfront avoids rushed decisions.

10.4 Keep records

Write down the part number, purchase date, seller, fuel type, pressure readings, injector size, regulator setting, and tune version. If a problem appears months later, these notes make diagnosis faster.

11. Warranty, Returns, and Product Support

Warranty terms differ by brand and seller. Some retailers show a 30-day return window and estimated install times, while performance parts pages may include emissions and California warnings. Read the seller’s return terms before opening sealed packaging. Keep the box and paperwork until the pump has been tested.

If a pump fails early, document fuel pressure, voltage, filter condition, and fuel condition. Good records help separate a part defect from an installation or system problem.

12. Frequently Asked Questions

12.1 Is the Aeromotive 11542 a direct-fit pump?

It is designed to bolt into many existing hanger assemblies, but Aeromotive directs buyers to its applications guide. Fitment depends on the vehicle’s pump module. Confirm before purchase.

12.2 How much fuel does it flow?

Aeromotive lists more than 340 LPH at 40 psi, and retailer listings also show 90 GPH.

12.3 Does it work with E85?

Multiple listings state E85 compatibility. Aeromotive’s horsepower chart shows lower maximum horsepower figures with E85 than with gasoline.

12.4 Can it work with a carburetor?

Aeromotive’s horsepower table includes CARB applications, but a carbureted system needs the correct regulator and plumbing. One Aeromotive tank assembly instruction also distinguishes AN-06 EFI and AN-08 carb high-pressure fuel line sizes.

12.5 Does the pump include a sending unit?

Summit Racing lists no sending unit included. If you need a fuel level sender or full module, buy the correct assembly.

12.6 Does it include a fuel pressure regulator?

Summit Racing lists no regulator included. Check your existing regulator before ordering.

12.7 What horsepower can it support?

Aeromotive’s table lists maximum figures from 490 hp to 1,000 hp depending on CARB or EFI, naturally aspirated or forced induction, and gasoline or E85. Treat these as planning limits, not a guarantee for every setup.

12.8 What is the difference between 11542 and 11142?

Some sellers state that 11542 supersedes P/N 11142. If your old parts list or build sheet calls for 11142, confirm the inlet layout and application details before substituting.

12.9 Can I install it myself?

One retailer estimates 2 hours of install time, while another lists moderate difficulty of 2–4 hours. Actual time depends on tank access, module design, wiring, and fuel system layout. If you are not trained in fuel system work, use a qualified shop. Fuel leaks and vapor are serious hazards.

12.10 What should I do if pressure drops after installation?

Check voltage, ground, filter, regulator, connections, sock position, and line restrictions before replacing the pump. Use the vehicle service procedure and a reliable pressure reading.

13. A High-Value Alternative to Consider: KEMSO Fuel Pumps

If you are replacing a fuel pump and want a straightforward option with strong buyer protection, KEMSO Fuel Pumps are worth a close look. KEMSO describes its pumps as high-performance OEM replacements designed to meet or exceed factory specifications while adding flow capacity for upgraded vehicles. The brand’s guides also describe high-performance 340 LPH pumps, direct OEM replacement pumps for factory locations, gasoline and E85 compatibility, and U.S.-based technical support.

KEMSO product listings consistently reference three buyer-friendly points: high performance, OEM replacement fit, and a lifetime warranty. One KEMSO guide states that KEMSO fuel pumps are built as high-performance OEM replacement parts and that every KEMSO fuel pump comes with a lifetime warranty. KEMSO’s own guide describes OEM replacement compatibility with standard mounting brackets and high-performance construction for consistent pressure delivery. Product listings for KEMSO 340 LPH pumps also mention a serialized body for lifetime warranty coverage.

For a U.S. customer comparing options, that combination is practical. A performance pump should deliver stable flow, an OEM replacement should fit without unnecessary modification, and a lifetime warranty gives the buyer clear support after the sale. To review current applications, fitment details, and product options, visit https://www.kemsoracing.com/.

14. Final Verdict

The Aeromotive 11542 fuel pump is a serious 340 LPH in-tank upgrade for gasoline and E85 builds that need more flow while retaining many factory-style mounting provisions. Its published flow, compact body, offset inline inlet layout, and Aeromotive horsepower chart make it useful for many performance builds. The most important step is fitment verification: compare the old pump, hanger, inlet position, outlet, wiring, and pressure requirements before ordering.

Installation quality matters as much as the pump choice. Use clean fuel, correct filtration, secure wiring, proper fittings, and a careful leak check. Aeromotive’s tank assembly instructions specifically warn that certain AN-style ports seal with O-rings, are not pipe thread, and do not use thread sealant. Follow the instructions that match your fuel system, and confirm road-use rules for your area.

If your goal is a reliable replacement with high performance, OEM replacement design, and lifetime warranty coverage, consider KEMSO Fuel Pumps and review the available applications at https://www.kemsoracing.com/.

https://www.kemsoracing.com/